Претраживање
Приказ резултата 1-10 од 14
Testing of intergranular and pitting corrosion in sensitized welded joints of austenitic stainless steel
(Serbia : Association of Metallurgical Engineers of Serbia, 2017)
Pitting corrosion resistance and intergranular corrosion of the austenitic stainless steel X5Cr Ni18-10 were tested on the base metal, heat affected zone and weld metal. Testing of pitting corrosion was performed by the ...
The influence of chemical composition on microstructure, hardness and electrical conductivity of Ag-Bi-In alloys at 100 degrees C
(Serbia : Association of Metallurgical Engineers of Serbia AMES, 2017)
Considering possible applications and scarceness of literature data, Ag-Bi-In system was investigated in terms of microstructure, mechanical and electrical properties of ternary alloys from an isothermal section at 100 °C. ...
Vertical accuracy of data on the topographic maps and their application in mining
(Institut za rudarstvo i metalurgiju Bor, 2017)
The paper describes some experiences and the methodology used for evaluation the vertical accuracy of data on the official (state) topographic maps. The vertical accuracy is an important element of quality 3D representation ...
How to review a scientific paper / Kako recenzirati naučni rad
(Belgrade, Serbia : Engineering Society for Corrosion, 2017)
A review process is a key factor which ensures reliable and accurate presentation of new, useful, and original scientific knowledge to the public. Despite of many shortcomings which this evaluation of scientific work has, ...
Ternary Bi-Cu-Ni alloys – thermodynamics, characterization, mechanical and electrical properties
(Serbia : Association of Metallurgical Engineers of Serbia, 2017)
The Bi–Cu–Ni ternary system belongs to the group of potential Cu-Ni-based advanced lead-free solder materials for high temperature application. The paper shows results of the thermodynamic calculations using general solution ...
Mechanical and electrical properties of ternary Ag-Bi-Ga system at 250 °C
(Serbia : Association of Metallurgical Engineers of Serbia, 2017)
This paper presents a comparative review of the experimental and thermodynamic assessment of a ternary Ag-Bi-Ga system. An isothermal section at 250 °C was calculated using optimized thermodynamic data for the constitutive ...
Wear resistance improvement of thermal plant fan mill impact plates based on numerical flow simulation
(Society for Structural Integrity and Life, Institute for Material Testing, 2017)
Numerical simulation of 3D multiphase flow is performed to determine the velocity field in the fan mill. The mixture model of the Euler-Euler approach is used. Recirculating gas is a primary phase that carries granular ...
The model for improving the manufacturing process in Serbian small-scale production enterprises / Model za unapređenje procesa proizvodnje u srpskim preduzećima sa maloserijskim tipom proizvodnje
(Economics institute, Belgrade, 2017)
The paper presents a theoretic model for improving the manufacturing process that was developed and tested in small-scale production enterprises. The model also represents a new organizational model which enables a complete ...
Production of rubber plasticizers based on waste PET: Techno-economical aspect / Sinteza plastifikatora iz otpadnog PET-a za primenu u gumenim proizvodima - tehno-ekonomska analiza
(Belgrade, Serbia : Engineering Society for Corrosion, 2017)
Production of rubber plasticizers, based on waste poly(ethylene terephthalate) (PET), and economic effectiveness of developed technologies are presented and discussed. Waste PET glycolyzates, named diisononyl terephthalate(DINTP), ...
Influence of welding current intensity on pitting corrosion resistance in welded joint of stainless steel X5CrNi18-10 / Uticaj jačine struje zavarivanja na otpornost prema piting koroziji zavarenog spoja nerđajućeg čelika X5CrNi18-10
(Belgrade, Serbia : Engineering Society for Corrosion, 2017)
The effect of welding current on the pitting corrosion resistance in the welded joint of austenitic stainless steel X5CrNi18-10 was tested. Welding was carried out using three different current intensity (110 A, 130 A and ...