Претраживање
Приказ резултата 31-40 од 47
Production of rubber plasticizers based on waste PET: Techno-economical aspect / Sinteza plastifikatora iz otpadnog PET-a za primenu u gumenim proizvodima - tehno-ekonomska analiza
(Belgrade, Serbia : Engineering Society for Corrosion, 2017)
Production of rubber plasticizers, based on waste poly(ethylene terephthalate) (PET), and economic effectiveness of developed technologies are presented and discussed. Waste PET glycolyzates, named diisononyl terephthalate(DINTP), ...
Tailoring the corrosion resistance of Zn-Mn coating by electrodeposition from deep eutectic solvents / Poboljšanje korozione postojanosti Zn-Mn prevlake, elektrohemijskim taloženjem iz dubokih eutektičkih smeša
(Belgrade, Serbia : Engineering Society for Corrosion, 2018)
Well adhered, homogenous coatings were obtained from deep eutectic solvents (DES) based on choline chloride and urea, at current densities up to 20 mA cm-2. The coatings' morphology was analyzed by atomic force microscopy, ...
Chemical corrosion of metals and alloys / Hemijska korozija metala i legura
(Belgrade, Serbia : Engineering Society for Corrosion, 2016)
In this paper, phenomena of chemical corrosion of metals and alloys in electrolyte solutions are analyzed. It is shown that iron, chromium and other metals and alloys dissolve much faster than is the corrosion rate determined ...
Indentation behaviour of 'soft film on hard substrate' composite system type / Ponašanje kompozitnih sistema tipa 'mek film na tvrdom supstratu' na testu utiskivanja
(Belgrade, Serbia : Engineering Society for Corrosion, 2015)
This investigation has been carried out in order to analyse and compare the hardness response of different composite systems of the same type, named 'soft film on hard substrate' composite system. Composite systems of mono- ...
Corrosion characteristics of laser-cleaned surfaces on iron artefact / Koroziona svojstva laserski čišćenih površina na artefaktu od gvožđa
(Belgrade : Engineering Society for Corrosion, 2020)
Nd:YAG laser was used for cleaning surfaces of cultural heritage iron artefacts covered with
corrosion products. The corrosion products were removed without damaging the base material.
Three different electrochemical ...
Correlation between crystal orientation and morphology of electrolytically produced powder particles: Analysis of the limiting cases / Korelacija izmedju orijentacije kristala i morfologije elektrolitički proizvedenih praškastih čestica - analiza graničnih slučajeva
(Belgrade, Serbia : Engineering Society for Corrosion, 2018)
Lead and nickel powder particles were produced by the processes of electrolysis and characterized by scanning electron microscope (SEM). The X-ray diffraction (XRD) analysis of the produced particles was done. Morphologies ...
Water quality as one of the possible causative agents of corrosion in thermal power plants / Kvalitet vode kao jedan od mogućih uzročnika korozije u termoenergetskim postrojenjima
(Belgrade, Serbia : Engineering Society for Corrosion, 2010)
Damage and cancellations of thermal power plants in large numbers are caused due to an inadequate quality of feed water, which occur due to different types of corrosion processes. Water is a good solvent and its chemical ...
Influence of the synthesis procedures on pt catalyst activity for ethanol electrooxidation reaction / Uticaj postupka sinteze na aktivnost platinskih katalizatora za reakciju elektrooksidacije etanola
(Belgrade, Serbia : Engineering Society for Corrosion, 2016)
Carbon supported platinum catalysts for ethanol electrooxidation were synthesized by modified polyol synthesis method, assisted by microwave or reflux heating. Synthesized catalysts were characterized by XRD, STM and TGA ...
Morphology of Fe-Ni alloy powders electrodeposited from citrate-sulfate containing solutions / Morfologija prahova Fe-Ni legura elektrohemijski istaloženih iz citratno-sulfatnih rastvora
(Belgrade, Serbia : Engineering Society for Corrosion, 2011)
The electrochemical deposition of the Fe-Ni alloy powders from citrate-sulfate containing electrolytes of different Ni/Fe ions concentration ratios at pH 4.5 was examined by the polarization measurements. All polarization ...
Influence of welding current intensity on pitting corrosion resistance in welded joint of stainless steel X5CrNi18-10 / Uticaj jačine struje zavarivanja na otpornost prema piting koroziji zavarenog spoja nerđajućeg čelika X5CrNi18-10
(Belgrade, Serbia : Engineering Society for Corrosion, 2017)
The effect of welding current on the pitting corrosion resistance in the welded joint of austenitic stainless steel X5CrNi18-10 was tested. Welding was carried out using three different current intensity (110 A, 130 A and ...