Претраживање
Приказ резултата 1-10 од 99
Study of microstructure and magnetic properties of optimally annealed R/Q Nd4.5Fe77B18.5 alloy
(Metalurgija, 2009)
The rapid-quenched (R/Q) and subsequently optimally annealed Nd-Fe-B alloy with 12 wt% Nd was characterized using the X-Ray diffractometry (XRD), transmission electron microscopy (TEM), high resolution transmission electron ...
Ternary Bi-Cu-Ni alloys – thermodynamics, characterization, mechanical and electrical properties
(Serbia : Association of Metallurgical Engineers of Serbia, 2017)
The Bi–Cu–Ni ternary system belongs to the group of potential Cu-Ni-based advanced lead-free solder materials for high temperature application. The paper shows results of the thermodynamic calculations using general solution ...
Hydrogen production by biomass gasification / Proizvodnja vodonika gasifikacijom biomase
(Inženjersko društvo za koroziju, 2017)
Hydrogen could be the important energy sources of the next period provided that its production,
transportation, and storage are solved. In this paper review of the production of hydrogen from
lignocellulosic feedstock ...
Field applicable methods for intergranular corrosion testing of stainless steels structures / Metode ispitivanja interkristalne korozije na konstrukcijama od nerđajućh čelika na terenu
(Society for Structural Integrity and Life, 2016)
Determination of the susceptibility of austenitic stainless steel X5CrNi18-10 to intergranular corrosion (IGC) is performed by measuring the corrosion potential Ecorr in a drop of a test solution with specific chemical ...
Effect of chemical composition on microstructure, hardness and electrical conductivity profiles of the Bi-Cu-Ga alloys at 100 °C
(Serbia : Association of Metallurgical Engineers of Serbia, 2016)
Theoretical calculation and experimental investigation of the isothermal section of a ternary Bi-Cu-Ga system at 100 oC are presented in this paper. Thermodynamic binary-based calculation of the isothermal section was ...
On the properties of hot forged Ti-6Al-4V alloy aimed for surgical implants
(Belgrade : Association of Metallurgical Engineers of Serbia, 2019)
The investigation here is aimed to examine the structural and mechanical changes that might have occurred during the hot forging process, a process to obtain a surgical hip implant, and the subsequent heat treatment. ...
Parallel-strip line stub resonator for permittivity characterization
(Niš : University of Niš, 2020)
A new type of a microwave permittivity sensor with a short open stub as a resonator is introduced. The open stub is realized as a double-sided parallel-strip line without a substrate and can be totally immersed into the ...
Testing of intergranular and pitting corrosion in sensitized welded joints of austenitic stainless steel
(Serbia : Association of Metallurgical Engineers of Serbia, 2017)
Pitting corrosion resistance and intergranular corrosion of the austenitic stainless steel X5Cr Ni18-10 were tested on the base metal, heat affected zone and weld metal. Testing of pitting corrosion was performed by the ...
The influence of chemical composition on microstructure, hardness and electrical conductivity of Ag-Bi-In alloys at 100 degrees C
(Serbia : Association of Metallurgical Engineers of Serbia AMES, 2017)
Considering possible applications and scarceness of literature data, Ag-Bi-In system was investigated in terms of microstructure, mechanical and electrical properties of ternary alloys from an isothermal section at 100 °C. ...
Wear resistance improvement of thermal plant fan mill impact plates based on numerical flow simulation
(Society for Structural Integrity and Life, Institute for Material Testing, 2017)
Numerical simulation of 3D multiphase flow is performed to determine the velocity field in the fan mill. The mixture model of the Euler-Euler approach is used. Recirculating gas is a primary phase that carries granular ...