Search
Now showing items 1-10 of 10
Corrosion causes in thermal power plants and ways of prevention / Uzroci korozije u termoenergetskim postrojenjima i načini prevencije
(Belgrade, Serbia : Engineering Society for Corrosion, 2009)
Corrosion damages often exert considerable influence on outages number and hence on the loss of thermal power plant availability. In order to accomplish the aim of reducing the corrosion to it's minimum and prevent main ...
Fundamental aspects of copper electrodeposition in the hydrogen Co-deposition range
(Belgrade, Serbia : Engineering Society for Corrosion, 2010)
This a review paper considering fundamental aspects of copper electrodeposition at high overpotentials where parallel to copper electrodeposition, hydrogen evolution reaction occurs. The two types of copper deposits are ...
Electrolysis conditions for obtaining cupric oxide (CUO) / Uslovi dobijanja bakar (II) oksida elektrolitičkim putem
(Belgrade, Serbia : Engineering Society for Corrosion, 2009)
Conditions for obtaining copper powder with different regimes of electrolysis [potentiostatic, galvanostatic and programmed current-voltage regimes ( periodically changing rate)] and effects on it's morphology and ...
Characterization of electrochemically synthesized pani on graphite electrode for potential use in electrochemical power sources / Elektrohemijska sinteza i karakterizacija elektrode od polianilina za potencijalnu upotrebu u elektrohemijskim izvorima energije
(Belgrade, Serbia : Engineering Society for Corrosion, 2009)
Polyaniline (PANI) on graphite electrode was synthesized electrochemically under galvanostatic condition at current density of 2.0 mA cm-2 from aqueous solution of 1.0 moldm-3 HCl and 0.25 mol dm-3 aniline monomer. ...
Comparison of morphology of powder particles obtained by the constant and periodically changing regimes of electrolysis / Poređenje morfologije čestica praha dobijenih konstantnim i periodično promenljivim režimima elektrolize
(Belgrade, Serbia : Engineering Society for Corrosion, 2011)
Morphologies of copper powder particles obtained by both potentiostatic and pulsating overpotential (PO) regimes of electrolysis were analyzed using the technique of scanning electron microscopy (SEM). The parameters of ...
Catalytic effect of sulphuric acid in the process of deposition of chromium coatings / Katalitički uticaj sumporne kiseline u procesu taloženja prevlaka hroma
(Belgrade, Serbia : Engineering Society for Corrosion, 2011)
This paper analyzes the catalytic effect of sulphuric acid on current efficiency, the coating thickness and the rate of deposition of electrochemical chromium coatings. According to the properties of chrome, there are three ...
Hydroxyapatite coatings on TiO2 nanotubes / Prevlake hidroksiapatita na nanotubama oksida titana
(Belgrade, Serbia : Engineering Society for Corrosion, 2010)
The aim of this work was to obtain nanotubular TiO2 layer by anodization of titanium substrate, and to prepare hydroxyapatite (HAP) coatings by electrophoretic deposition over nanotubular TiO2 layer. The presence of fluoride ...
Water quality as one of the possible causative agents of corrosion in thermal power plants / Kvalitet vode kao jedan od mogućih uzročnika korozije u termoenergetskim postrojenjima
(Belgrade, Serbia : Engineering Society for Corrosion, 2010)
Damage and cancellations of thermal power plants in large numbers are caused due to an inadequate quality of feed water, which occur due to different types of corrosion processes. Water is a good solvent and its chemical ...
Morphology of Fe-Ni alloy powders electrodeposited from citrate-sulfate containing solutions / Morfologija prahova Fe-Ni legura elektrohemijski istaloženih iz citratno-sulfatnih rastvora
(Belgrade, Serbia : Engineering Society for Corrosion, 2011)
The electrochemical deposition of the Fe-Ni alloy powders from citrate-sulfate containing electrolytes of different Ni/Fe ions concentration ratios at pH 4.5 was examined by the polarization measurements. All polarization ...
The electrochemical deposition and corrosion stability of Zn-Mn alloy coatings / Elektrohemijsko taloženje i koroziona stabilnost prevlaka Zn-Mn legura
(Belgrade, Serbia : Engineering Society for Corrosion, 2010)
The influence of the type of the deposition solution on the current efficiency during electrodeposition of Zn-Mn alloys was examined. The Zn-Mn alloys were deposited on steel from chloride, sulphate and pyrophosphate plating ...