Претраживање
Приказ резултата 1-10 од 19
Electrochemical and structural properties of Ni(II)-alumina composites as an annealing temperature function
(International Institute for the Science of Sintering, Beograd, 2019)
Alumina powders, pure and doped with nickel, were synthetized by sol-gel method and calcined at 500, 900 and 1100°C in order to obtain mesoporous structures with a high specific surface area, well adapTab. to catalytic ...
Structural characterization of the nickel thin film deposited by glad technique
(International Institute for the Science of Sintering, Beograd, 2013)
In this work, a columnar structure of nickel thin film has been obtained using an advanced deposition technique known as Glancing Angle Deposition. Nickel thin film was deposited on glass sample at the constant emission ...
Thermal diffusivity of single crystal Bi0.9Sb0.1
(International Institute for the Science of Sintering, Beograd, 2010)
A single crystal Bi0.9Sb0.1 ingot was synthesized using the Bridgman technique. Thermal diffusivity and electronic transport properties of single crystal cleaved plates (00l) were determined from PA photoacoustic phase and ...
Synthesis of Highly Porous Al2O3-YAG Composite Ceramics
(International Institute for the Science of Sintering, Beograd, 2016)
Al2O3-YAG composite was obtained by sintering of porous Al2O3 preforms infiltrated with water solution of aluminium nitrate nonahydrate, Al(NO3)(3)center dot 9H(2)O and yttrium nitrate hexahydrate, Y(NO3)(3)center dot ...
Methanol electrooxidation on PtRu modified zeolite X
(International Institute for the Science of Sintering, Beograd, 2013)
Zeolite NaX (faujasite type) was used as a support for platinum-ruthenium catalyst. A procedure for thermal decomposition of noble metal acetylacetonates to deposit noble metal clusters on the surface of solid support was ...
State of the Art and Challenges in Development of Electrical Contact Materials in the Light of the RoHS Directive
(International Institute for the Science of Sintering, Beograd, 2012)
The article surveys current state of the art and challenges in the development of the electrical contact materials in the light of the EU Directive on Restriction of Hazardous Substances (RoHS). The focus was placed on ...
Two Step Sintering of ZnTiO3 nanopowder
(International Institute for the Science of Sintering, Beograd, 2017)
Metastable nanopowder ZnTiO3 was pressed into cylindrical compacts at 200 MPa. Compacts were treated by conventional heating with isothermal holding at 931 degrees C for 10 minutes, 25 minutes and 40 minutes. ZnTiO3 compacts ...
Microstructure refinement and physical properties of Ag-SnO2 based contact materials prepared by high-energy ball milling
(International Institute for the Science of Sintering, Beograd, 2013)
High energy ball milling was used in order to improve dispersion of metal oxide in Ag-SnO2 electrical contact materials. The processed Ag-SnO2 (92:8) and Ag-SnO2In2O3 (87.8:9.30:2.9) powder mixtures were subsequently ...
Formation of Magnetic Microstructure of the Nanosized NiFe2O4 Synthesized Via Solid-State Reaction
(International Institute for the Science of Sintering, Beograd, 2012)
Magnetic NiFe2O4 structure formation was studied through structural, compositional and magnetic characterization of obtained reaction products of a simple, high yielding and low-cost solid-state reaction. Initial annealing ...
Impact of Alumina Particles on the Morphology and Mechanics of Hybrid Wood Plastic Composite Materials
(Belgrade : Association for ETRAN Society, 2019)
Hybrid composite panels of Wood-Plastic Composites (WPC) consisting of wood and
poly (methyl methacrylate) (PMMA) were reinforced with alumina particles and made by
“hot pressing” method. Alumina-based particles were ...