Претраживање
Приказ резултата 181-190 од 223
Bio-renewable membranes based on modified cellulose, lignin, and tannic acid for difenoconazole and thiophanate-methyl removal
(Zvornik : Faculty of Technology, 2021)
Aquatic pollution caused by pesticides as a consequence through run-off, leaching, and subsurface drainage, may pose a serious health hazard for living being and ecosystems due to
pesticides persistent nature and ...
Structurally modified three-dimensionally ordered (3DOM) alumina linked to subgleba of Handkea utriformis for Pb2+ removal
(Faculty of Technology Leskovac, 2021)
Water pollution is a consequence of permanent technological development, urbanization and industrialization, having a huge impact on human health and the environment. Thus, metal oxides received considerable scientific ...
FTIR spectroscopy analysis of mechanochemically activated Na2CO3 during relaxation time
(University of Belgrade, Faculty of Mechanical EngineeringSerbian Tribology Society, 2021)
Sodium carbonate was mechanically activated for 7 minutes in a vibro mill at a frequency of 3000 oscillations per minute. Activated samples were stored in the air at room conditions for 31 days. To monitor the kinetics of ...
Cysteine and modified cysteine as green inhibitors of aluminum alloy corrosion
(Faculty of Technology Zvornik – University of East Sarajevo, 2021)
In its pure form, aluminum is easy to process and has a high level of corrosion resistance. However, due to its low strength the possibility of application of pure aluminum is reduced. When alloyed, aluminum alloys are ...
Synthesis and pharmacology evaluation of novel 1-benzyl-n-(4-(4-arylpiperazin-1-yl)phenyl)piperidin-4-carboxamides, as potential acetylcholinesterase inhibitors
(Division of Medicinal Chemistry and Chemical Biology of the Swiss Chemical SocietyEuropean Federation for Medicinal Chemistry and Chemical Biology (EFMC), 2021)
Alzheimer’s disease (AD) is a neurodegenerative disease which affects over 50 milion people worldwide.1) AD
mainly affects people ages 65 and above. Symptoms are memory loss, decline in learning capacity, and language
problems. ...
The influence of the addition of brushite on the mechanical properties of geopolymer binder
(Belgrade: Vinča Institute of Nuclear Sciences-National Institute of the Republic of Serbia, 2021)
The growing need to protect the environment and reuse abandoned raw materials is increasingly used in the construction industry to make in addition to cementitious materials and geopolymer materials. Geopolymers are ...
Effect of different cobalt loadings on the electrochemical performance of aluminum pillared clay-supported cobalt towards glucose oxidation
(Belgrade : Institute of Technical Sciences of SASABelgrade : Materials Research Society of Serbia, 2021)
This work is focused on our further efforts to improve the electrochemical performance of cobalt oxide supported on aluminum pillared clay (CoAP) towards glucose oxidation [1]. To this end, the effect of different cobalt ...
Ft-IR spectroscopy as a simple tool for rapid solution of various problems
(Societat Catalana de Química (SCQ) (Catalan Chemical Society)EuChemS Divison of Organic Chemistry, 2021)
FTIR spectroscopy is non-destructive and simple analytical technique that requires
small sample amounts for providing information about functional groups in molecules. In
certain cases, it is indispensable for structure ...
Antibacterial and Antibiofilm Activity of Flavonoid and Saponin Derivatives from Atriplex tatarica against Pseudomonas aeruginosa
(Portugal : PROTEOMASS Scientific Society, 2021)
A new flavonoid glucoside derivative, patuletin 3-O-(2-O-feruloyl)-β-D-glucuronopyranosyl-(1→2)-β-Dglucopyranoside, named atriplexin IV (1), and three new triterpenoid saponin derivatives, two sulfonylated, β-
D-glucopy ...
Primer realizacije uzorka pomoću 3D štampe i analiza problema u kvalitetu
(Beograd : JUSK - Jedinstveno Udruženje Srbije za Kvalitet / Belgrade : UASQ - United Association of Serbia for Quality, 2021)
Iako 3D štampa verovatno neće preuzeti mnoge konvencionalne metode proizvodnje, 3D štampač može brzo da isporuči složeni dizajn sa velikom tačnošću. Međutim, aditivna proizvodnja takođe pokazuje određene slabosti. Ako ...