Претраживање
Приказ резултата 1-10 од 39
Chemical corrosion of metals and alloys / Hemijska korozija metala i legura
(Belgrade, Serbia : Engineering Society for Corrosion, 2016)
In this paper, phenomena of chemical corrosion of metals and alloys in electrolyte solutions are analyzed. It is shown that iron, chromium and other metals and alloys dissolve much faster than is the corrosion rate determined ...
Corrosion properties of an aluminium alloy 7000 series after a new two step precipitation hardening / Otpornost prema koroziji aluminijumske legure serije 7000 posle novog dvostepenog termičkog taloženja
(Belgrade, Serbia : Engineering Society for Corrosion, 2014)
Corrosion properties of an aluminium alloy 7000 series were investigated by different electrochemical methods. The alloy was subjected to the one-step and to a new two-step precipitation hardening. Polarization measurements ...
The resistance to general corrosion of series of zinc-aluminum alloys modified with silicon and strontiumloys modified with silicon and strontium / Otpornost na opštu koroziju serije legura cink-aluminijum koje su modifikovane silicijumom i stroncijumom
(Belgrade : Engineering Society for Corrosion, 2019)
The resistance to corrosion of the series of zinc-aluminum casting alloys modified with silicon and
strontium was studied in a sodium chloride solution. It was shown that general corrosion was the
main form of corrosion ...
Testing the protective ability of corrosion inhibitors in dilute chloride solutions / Ispitivanje zaštitne sposobnosti inhibitora korozije u razblaženim rastvorima hlorida
(Belgrade, Serbia : Engineering Society for Corrosion, 2017)
After sterilization of meat cans in a factory of meat and meat products in Serbia, occurence of corrosion on the can lids was observed. Sterilization of cans is usually performed in the presence of corrosion inhibitors. ...
Determination of the weld metal corrosion rate using electrochemical techniques / Određivanje brzine korozije metala šava u zavarenom spoju pomoću elektrohemijskih tehnika
(Belgrade, Serbia : Engineering Society for Corrosion, 2015)
To determine corrosion rate of the base metal and weld metal were applied electrochemical techniques: linear polarization resistance, linear sweep voltammetry and electrochemical impedance spectroscopy. The samples were ...
Influence of welding current intensity on pitting corrosion resistance in welded joint of stainless steel X5CrNi18-10 / Uticaj jačine struje zavarivanja na otpornost prema piting koroziji zavarenog spoja nerđajućeg čelika X5CrNi18-10
(Belgrade, Serbia : Engineering Society for Corrosion, 2017)
The effect of welding current on the pitting corrosion resistance in the welded joint of austenitic stainless steel X5CrNi18-10 was tested. Welding was carried out using three different current intensity (110 A, 130 A and ...
Direct synthesis of noble metal nanostructures on carbon support by hydrothermal process / Direktna sinteza nanostrukturnog plemenitog metala na ugljeničnoj osnovi pomoću hidrotermalnog procesa
(Belgrade, Serbia : Engineering Society for Corrosion, 2015)
Nanostructures of noble metals (Pt and Ag) on carbon support were prepared from fructose and solution of the Nobel metal salts (H2PtCl6 x 6H2O or AgNO3) under hydrothermal conditions. Commercial fructose (C6H12O6) acts as ...
Influence of the synthesis procedures on pt catalyst activity for ethanol electrooxidation reaction / Uticaj postupka sinteze na aktivnost platinskih katalizatora za reakciju elektrooksidacije etanola
(Belgrade, Serbia : Engineering Society for Corrosion, 2016)
Carbon supported platinum catalysts for ethanol electrooxidation were synthesized by modified polyol synthesis method, assisted by microwave or reflux heating. Synthesized catalysts were characterized by XRD, STM and TGA ...
Correlation between crystal orientation and morphology of electrolytically produced powder particles: Analysis of the limiting cases / Korelacija izmedju orijentacije kristala i morfologije elektrolitički proizvedenih praškastih čestica - analiza graničnih slučajeva
(Belgrade, Serbia : Engineering Society for Corrosion, 2018)
Lead and nickel powder particles were produced by the processes of electrolysis and characterized by scanning electron microscope (SEM). The X-ray diffraction (XRD) analysis of the produced particles was done. Morphologies ...
Molecular descriptors as proxies for the modeling of the materials and their environmental impact / Računarski generisani molekulski deskriptori kao proxi-ji za modelovanje materijala i njihovog uticaja
(Belgrade : Engineering Society for Corrosion, 2016)
For the prediction of material's properties and of interaction of molecules with the surroundings, one needs to know their properties. Usually, the molecular properties are revealed through experimental measurements. It ...