TY  - JOUR
AU  - Zarubica, Aleksandra
AU  - Krstić, Jugoslav
AU  - Popović, Dejan
AU  - Krstić, Aleksandra
AU  - Ljupković, Radomir
AU  - Ranđelović, Marjan
AU  - Matović, Branko
PY  - 2021
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/4802
AB  - New binary catalytic systems based on sulphated zirconia-alumina were synthesized by controlled hydrolysis of alkoxides using relative molar ratios of constituents 1:1, 1:2 and 1:3 in favour of zirconia. The obtained differences in the final catalytic material’s properties may be related to organic precursor memory effect, the applied calcinations temperatures and used alumina contents. The addition of alumina to zirconia affected the structural and surface properties stabilizing bare zirconia by means of slower phase transformation of tetragonal zirconia crystal phase into monoclinic one, further resulting in smaller crystallites sizes and higher surface density of acidic function (sulphates). The best alumina impact on physico-chemical properties was achieved when the highest amount of alumina (e.g. 50%) and lower calcination temperature (500°C) were used, causing relatively high steady-state activity in isomerization of n-hexane at reaction temperature 250 °C. On the other hand, higher calcination temperature (600 °C) played a role in the genesis of greater sulphate density. Catalytic activity and selectivity are expressed as a complex synergistic function of relative density of acid sites together with positive status of other optimized physico-chemical properties of the catalytic material (by activation and calcination temperatures).
PB  - Novi Sad : University of Novi Sad, Faculty of Technology
T2  - Processing and Application of Ceramics
T1  - Influence of alumina addition on structural and catalytic properties of sulphated zirconia in isomerization of n-hexane
VL  - 15
IS  - 2
SP  - 136
DO  - 10.2298/PAC2102111Z
ER  - 

@article{
author = "Zarubica, Aleksandra and Krstić, Jugoslav and Popović, Dejan and Krstić, Aleksandra and Ljupković, Radomir and Ranđelović, Marjan and Matović, Branko",
year = "2021",
abstract = "New binary catalytic systems based on sulphated zirconia-alumina were synthesized by controlled hydrolysis of alkoxides using relative molar ratios of constituents 1:1, 1:2 and 1:3 in favour of zirconia. The obtained differences in the final catalytic material’s properties may be related to organic precursor memory effect, the applied calcinations temperatures and used alumina contents. The addition of alumina to zirconia affected the structural and surface properties stabilizing bare zirconia by means of slower phase transformation of tetragonal zirconia crystal phase into monoclinic one, further resulting in smaller crystallites sizes and higher surface density of acidic function (sulphates). The best alumina impact on physico-chemical properties was achieved when the highest amount of alumina (e.g. 50%) and lower calcination temperature (500°C) were used, causing relatively high steady-state activity in isomerization of n-hexane at reaction temperature 250 °C. On the other hand, higher calcination temperature (600 °C) played a role in the genesis of greater sulphate density. Catalytic activity and selectivity are expressed as a complex synergistic function of relative density of acid sites together with positive status of other optimized physico-chemical properties of the catalytic material (by activation and calcination temperatures).",
publisher = "Novi Sad : University of Novi Sad, Faculty of Technology",
journal = "Processing and Application of Ceramics",
title = "Influence of alumina addition on structural and catalytic properties of sulphated zirconia in isomerization of n-hexane",
volume = "15",
number = "2",
pages = "136",
doi = "10.2298/PAC2102111Z"
}

Zarubica, A., Krstić, J., Popović, D., Krstić, A., Ljupković, R., Ranđelović, M.,& Matović, B.. (2021). Influence of alumina addition on structural and catalytic properties of sulphated zirconia in isomerization of n-hexane. in Processing and Application of Ceramics
Novi Sad : University of Novi Sad, Faculty of Technology., 15(2), 136.
https://doi.org/10.2298/PAC2102111Z

Zarubica A, Krstić J, Popović D, Krstić A, Ljupković R, Ranđelović M, Matović B. Influence of alumina addition on structural and catalytic properties of sulphated zirconia in isomerization of n-hexane. in Processing and Application of Ceramics. 2021;15(2):136.
doi:10.2298/PAC2102111Z .

Zarubica, Aleksandra, Krstić, Jugoslav, Popović, Dejan, Krstić, Aleksandra, Ljupković, Radomir, Ranđelović, Marjan, Matović, Branko, "Influence of alumina addition on structural and catalytic properties of sulphated zirconia in isomerization of n-hexane" in Processing and Application of Ceramics, 15, no. 2 (2021):136,
https://doi.org/10.2298/PAC2102111Z . .

TY  - CONF
AU  - Volkov Husović, Tatjana
AU  - Simić, Marko
AU  - Martinović, Sanja
AU  - Vlahović, Milica
PY  - 2021
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/5945
AB  - The objectives and effects of refractory materials recycling, as well as the potential
industries from which waste refractories suitable for recycling can be collected, will be
discussed in this paper. After the end of its service life, the refractory material is usually
disposed of at industrial landfills or recycled. The main motive for the reuse of refractories is the
sustainable conservation of natural resources and environmental protection by reducing
CO2 emissions and industrial landfills, reducing landfill costs and users’ costs. The effects
achieved by refractory materials recycling are the cost savings of raw materials and disposal,
the improvement of the environment, the product line expansion, and consequently the
opportunities for products' placement in hitherto unknown and inaccessible markets, as well
as closer cooperation between users and suppliers. Respecting recycling policies brings us
closer to the concept of zero waste.
PB  - Association for Promotion of Holistic Approach to Environment
C3  - Proceedings book - 2nd International Conference „The Holistic Approach to Environment“, May 28th, 2021, Virtual conference
T1  - Recycling refractories for steelmaking processes
SP  - 642
EP  - 652
UR  - https://hdl.handle.net/21.15107/rcub_cer_5945
ER  - 

@conference{
author = "Volkov Husović, Tatjana and Simić, Marko and Martinović, Sanja and Vlahović, Milica",
year = "2021",
abstract = "The objectives and effects of refractory materials recycling, as well as the potential
industries from which waste refractories suitable for recycling can be collected, will be
discussed in this paper. After the end of its service life, the refractory material is usually
disposed of at industrial landfills or recycled. The main motive for the reuse of refractories is the
sustainable conservation of natural resources and environmental protection by reducing
CO2 emissions and industrial landfills, reducing landfill costs and users’ costs. The effects
achieved by refractory materials recycling are the cost savings of raw materials and disposal,
the improvement of the environment, the product line expansion, and consequently the
opportunities for products' placement in hitherto unknown and inaccessible markets, as well
as closer cooperation between users and suppliers. Respecting recycling policies brings us
closer to the concept of zero waste.",
publisher = "Association for Promotion of Holistic Approach to Environment",
journal = "Proceedings book - 2nd International Conference „The Holistic Approach to Environment“, May 28th, 2021, Virtual conference",
title = "Recycling refractories for steelmaking processes",
pages = "642-652",
url = "https://hdl.handle.net/21.15107/rcub_cer_5945"
}

Volkov Husović, T., Simić, M., Martinović, S.,& Vlahović, M.. (2021). Recycling refractories for steelmaking processes. in Proceedings book - 2nd International Conference „The Holistic Approach to Environment“, May 28th, 2021, Virtual conference
Association for Promotion of Holistic Approach to Environment., 642-652.
https://hdl.handle.net/21.15107/rcub_cer_5945

Volkov Husović T, Simić M, Martinović S, Vlahović M. Recycling refractories for steelmaking processes. in Proceedings book - 2nd International Conference „The Holistic Approach to Environment“, May 28th, 2021, Virtual conference. 2021;:642-652.
https://hdl.handle.net/21.15107/rcub_cer_5945 .

Volkov Husović, Tatjana, Simić, Marko, Martinović, Sanja, Vlahović, Milica, "Recycling refractories for steelmaking processes" in Proceedings book - 2nd International Conference „The Holistic Approach to Environment“, May 28th, 2021, Virtual conference (2021):642-652,
https://hdl.handle.net/21.15107/rcub_cer_5945 .

TY  - JOUR
AU  - Savić, Aleksandar R.
AU  - Martinović, Sanja
AU  - Vlahović, Milica
AU  - Volkov Husović, Tatjana
PY  - 2020
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3763
AB  - Self-compacting concrete (SCC) contains fine mineral fillers such as limestone powder. The idea of this study was to partially replace limestone with waste sulfur since it is hydrophobic, insoluble in water and therefore chemically inert and to compare the properties of produced concrete samples. Fresh concrete properties included: slump-flow, t500, V-funnel time, L-box ratio, segregation ratio, density, and entrained air content. Hardened concrete was tested for compressive, flexural and bond strengths, ultrasonic velocity, dynamic elasticity modulus, dynamic Poisson’s ratio, and microstructure. Flowability and segregation increased, while bulk density, compressive and flexural strength, dynamic elasticity modulus and ultrasonic velocity slight declined. Times t500 and V-funnel time, L-box ratio and entrained air changed insignificantly. Considering that all properties should remain or improve in case of waste valorization and the criteria should set to satisfy requirements for SCC, this study proved that all mixtures can be used for structural applications.
AB  - Efectos del contenido de residuos de azufre en las propiedades del hormigón autocompactante. El 
hormigón autocompactante (SCC, del inglés Self-compacting concrete) contiene cargas (fillers) minerales finas como polvo de piedra caliza. La idea de este estudio fue reemplazar parcialmente la piedra caliza por contenido de residuos de azufre, ya que es hidrófobo, insoluble en agua y, por lo tanto, químicamente inerte, y comparar las propiedades de las muestras de hormigón producidas. Las propiedades analizadas en el hormigón fresco 
incluyeron: flujo de asentamiento, t500, tiempo del embudo en V (V-funnel time), relación de caja en L (L-box ratio), relación de segregación, densidad y contenido de aire ocluido. En el hormigón endurecido se analizó la resistencia a compresión, flexión y adherencia, velocidad ultrasónica, módulo dinámico de elasticidad, coefi ciente dinámico de Poisson y microestructura. La fluidez y la segregación aumentaron, mientras que la densidad aparente (bulk density), la resistencia a la compresión y la flexión, el módulo de elasticidad dinámica y la velocidad ultrasónica disminuyeron ligeramente. Los tiempos t500 y el tiempo del embudo V, la relación de la caja L y el aire ocluido cambiaron de manera insignificante. Considerando que al valorizar residuos, se deben conseguir propiedades similares o mejoradas, y que los criterios deben establecerse para satisfacer los requisitos de SCC, este estudio demostró que todas las mezclas se pueden utilizar para aplicaciones estructurales.
PB  - Consejo Superior de Investigaciones Cientificas - CSIC
T2  - Materiales de Construccion
T1  - Effects of waste sulfur content on properties of self-compacting concrete
VL  - 70
IS  - 338
SP  - e216
DO  - 10.3989/mc.2020.06919
ER  - 

@article{
author = "Savić, Aleksandar R. and Martinović, Sanja and Vlahović, Milica and Volkov Husović, Tatjana",
year = "2020",
abstract = "Self-compacting concrete (SCC) contains fine mineral fillers such as limestone powder. The idea of this study was to partially replace limestone with waste sulfur since it is hydrophobic, insoluble in water and therefore chemically inert and to compare the properties of produced concrete samples. Fresh concrete properties included: slump-flow, t500, V-funnel time, L-box ratio, segregation ratio, density, and entrained air content. Hardened concrete was tested for compressive, flexural and bond strengths, ultrasonic velocity, dynamic elasticity modulus, dynamic Poisson’s ratio, and microstructure. Flowability and segregation increased, while bulk density, compressive and flexural strength, dynamic elasticity modulus and ultrasonic velocity slight declined. Times t500 and V-funnel time, L-box ratio and entrained air changed insignificantly. Considering that all properties should remain or improve in case of waste valorization and the criteria should set to satisfy requirements for SCC, this study proved that all mixtures can be used for structural applications., Efectos del contenido de residuos de azufre en las propiedades del hormigón autocompactante. El 
hormigón autocompactante (SCC, del inglés Self-compacting concrete) contiene cargas (fillers) minerales finas como polvo de piedra caliza. La idea de este estudio fue reemplazar parcialmente la piedra caliza por contenido de residuos de azufre, ya que es hidrófobo, insoluble en agua y, por lo tanto, químicamente inerte, y comparar las propiedades de las muestras de hormigón producidas. Las propiedades analizadas en el hormigón fresco 
incluyeron: flujo de asentamiento, t500, tiempo del embudo en V (V-funnel time), relación de caja en L (L-box ratio), relación de segregación, densidad y contenido de aire ocluido. En el hormigón endurecido se analizó la resistencia a compresión, flexión y adherencia, velocidad ultrasónica, módulo dinámico de elasticidad, coefi ciente dinámico de Poisson y microestructura. La fluidez y la segregación aumentaron, mientras que la densidad aparente (bulk density), la resistencia a la compresión y la flexión, el módulo de elasticidad dinámica y la velocidad ultrasónica disminuyeron ligeramente. Los tiempos t500 y el tiempo del embudo V, la relación de la caja L y el aire ocluido cambiaron de manera insignificante. Considerando que al valorizar residuos, se deben conseguir propiedades similares o mejoradas, y que los criterios deben establecerse para satisfacer los requisitos de SCC, este estudio demostró que todas las mezclas se pueden utilizar para aplicaciones estructurales.",
publisher = "Consejo Superior de Investigaciones Cientificas - CSIC",
journal = "Materiales de Construccion",
title = "Effects of waste sulfur content on properties of self-compacting concrete",
volume = "70",
number = "338",
pages = "e216",
doi = "10.3989/mc.2020.06919"
}

Savić, A. R., Martinović, S., Vlahović, M.,& Volkov Husović, T.. (2020). Effects of waste sulfur content on properties of self-compacting concrete. in Materiales de Construccion
Consejo Superior de Investigaciones Cientificas - CSIC., 70(338), e216.
https://doi.org/10.3989/mc.2020.06919

Savić AR, Martinović S, Vlahović M, Volkov Husović T. Effects of waste sulfur content on properties of self-compacting concrete. in Materiales de Construccion. 2020;70(338):e216.
doi:10.3989/mc.2020.06919 .

Savić, Aleksandar R., Martinović, Sanja, Vlahović, Milica, Volkov Husović, Tatjana, "Effects of waste sulfur content on properties of self-compacting concrete" in Materiales de Construccion, 70, no. 338 (2020):e216,
https://doi.org/10.3989/mc.2020.06919 . .

TY  - JOUR
AU  - Maksimović, Vesna M.
AU  - Kusigerski, Vladan B.
AU  - Stoiljković, Milovan
AU  - Maletaškić, Jelena
AU  - Nikolić, Nebojša D.
PY  - 2020
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3575
AB  - Nickel−cobalt (Ni−Co) alloy powders were produced galvanostatically by using sulphate electrolytes with
various ratios of Ni2+/Co2+ (mole ratios). The morphology, phase structure, chemical composition and magnetic
properties were examined by scanning electron microscope (SEM), X-ray diffractometer (XRD), atomic emission
spectrometer (AES), and SQUID-based magnetometer, respectively. Morphology of the particles changed from
cauliflower-like and dendritic to coral-like and spongy-like ones with increasing Ni2+/Co2+ ratio from 0.25 to 4.0. XRD
analysis of the Ni−Co powders revealed that the decrease of Ni2+/Co2+ ratios (the increase of Co content) caused a
change of structure from face centered cubic (FCC) obtained for the ratios of 4.0, 1.5 and 0.67 to a mixture of FCC and
hexagonal closed-packed (HCP) phases for the ratio of 0.25. The increasing content of nickel led to change of
mechanism of electrolysis from irregular (up to ~40 wt.% Ni in the electrolytes) to close to equilibrium (between
~40 and 60 wt.% Ni in the electrolytes) and anomalous co-deposition (over 60 wt.% Ni in the electrolytes) type. All of
the obtained Ni−Co alloy samples behaved as soft magnetic materials while their magnetic parameters showed
immediate composition dependence since both coercivity and saturation magnetization almost linearly increased with
increase of the Co content.
PB  - Elsevier
T2  - Transactions of Nonferrows Metals Society of China
T1  - Influence of Ni2+/Co2+ ratio in electrolyte on morphology, structure and magnetic properties of electrolytically produced Ni−Co alloy powders
VL  - 30
IS  - 4
SP  - 1046
EP  - 1057
DO  - 10.1016/S1003-6326(20)65276-1
ER  - 

@article{
author = "Maksimović, Vesna M. and Kusigerski, Vladan B. and Stoiljković, Milovan and Maletaškić, Jelena and Nikolić, Nebojša D.",
year = "2020",
abstract = "Nickel−cobalt (Ni−Co) alloy powders were produced galvanostatically by using sulphate electrolytes with
various ratios of Ni2+/Co2+ (mole ratios). The morphology, phase structure, chemical composition and magnetic
properties were examined by scanning electron microscope (SEM), X-ray diffractometer (XRD), atomic emission
spectrometer (AES), and SQUID-based magnetometer, respectively. Morphology of the particles changed from
cauliflower-like and dendritic to coral-like and spongy-like ones with increasing Ni2+/Co2+ ratio from 0.25 to 4.0. XRD
analysis of the Ni−Co powders revealed that the decrease of Ni2+/Co2+ ratios (the increase of Co content) caused a
change of structure from face centered cubic (FCC) obtained for the ratios of 4.0, 1.5 and 0.67 to a mixture of FCC and
hexagonal closed-packed (HCP) phases for the ratio of 0.25. The increasing content of nickel led to change of
mechanism of electrolysis from irregular (up to ~40 wt.% Ni in the electrolytes) to close to equilibrium (between
~40 and 60 wt.% Ni in the electrolytes) and anomalous co-deposition (over 60 wt.% Ni in the electrolytes) type. All of
the obtained Ni−Co alloy samples behaved as soft magnetic materials while their magnetic parameters showed
immediate composition dependence since both coercivity and saturation magnetization almost linearly increased with
increase of the Co content.",
publisher = "Elsevier",
journal = "Transactions of Nonferrows Metals Society of China",
title = "Influence of Ni2+/Co2+ ratio in electrolyte on morphology, structure and magnetic properties of electrolytically produced Ni−Co alloy powders",
volume = "30",
number = "4",
pages = "1046-1057",
doi = "10.1016/S1003-6326(20)65276-1"
}

Maksimović, V. M., Kusigerski, V. B., Stoiljković, M., Maletaškić, J.,& Nikolić, N. D.. (2020). Influence of Ni2+/Co2+ ratio in electrolyte on morphology, structure and magnetic properties of electrolytically produced Ni−Co alloy powders. in Transactions of Nonferrows Metals Society of China
Elsevier., 30(4), 1046-1057.
https://doi.org/10.1016/S1003-6326(20)65276-1

Maksimović VM, Kusigerski VB, Stoiljković M, Maletaškić J, Nikolić ND. Influence of Ni2+/Co2+ ratio in electrolyte on morphology, structure and magnetic properties of electrolytically produced Ni−Co alloy powders. in Transactions of Nonferrows Metals Society of China. 2020;30(4):1046-1057.
doi:10.1016/S1003-6326(20)65276-1 .

Maksimović, Vesna M., Kusigerski, Vladan B., Stoiljković, Milovan, Maletaškić, Jelena, Nikolić, Nebojša D., "Influence of Ni2+/Co2+ ratio in electrolyte on morphology, structure and magnetic properties of electrolytically produced Ni−Co alloy powders" in Transactions of Nonferrows Metals Society of China, 30, no. 4 (2020):1046-1057,
https://doi.org/10.1016/S1003-6326(20)65276-1 . .

TY  - JOUR
AU  - Kazasidis, Marios
AU  - Yin, Shuo
AU  - Cassidy, Jonathan
AU  - Volkov-Husović, Tatjana
AU  - Vlahović, Milica
AU  - Martinović, Sanja
AU  - Kyriakopoulou, Elena
AU  - Lupoi, Rocco
PY  - 2020
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3387
AB  - The cold spray technique was employed in this study to produce pure nickel (Ni) and nickel-Inconel 718 powder deposits on duplex stainless steel substrates. High quality coatings were manufactured using nitrogen as the propellant gas. The coatings exhibited satisfactory Inconel 718 (In718) retention within the Ni matrix due to the highly ductile binder phase necessary for fabrication. The characterization of the coating microstructures was implemented by means of X-ray diffraction, electron microscopy, energy-dispersive X-ray spectroscopy, and microhardness testing. In addition, the erosion resistance of both coatings was evaluated by performing cavitation erosion tests, with the analysis of the eroded surfaces revealing different erosion mechanisms for each coating. The results demonstrated the efficiency of the cold spray technique for use in the production of metal-metal matrix composite coatings and the potential of In718 use in applications which demand enhanced cavitation erosion resistance.
PB  - Elsevier
T2  - Surface and Coatings Technology
T1  - Microstructure and cavitation erosion performance of nickel-Inconel 718 composite coatings produced with cold spray
VL  - 382
SP  - 125195
DO  - 10.1016/j.surfcoat.2019.125195
ER  - 

@article{
author = "Kazasidis, Marios and Yin, Shuo and Cassidy, Jonathan and Volkov-Husović, Tatjana and Vlahović, Milica and Martinović, Sanja and Kyriakopoulou, Elena and Lupoi, Rocco",
year = "2020",
abstract = "The cold spray technique was employed in this study to produce pure nickel (Ni) and nickel-Inconel 718 powder deposits on duplex stainless steel substrates. High quality coatings were manufactured using nitrogen as the propellant gas. The coatings exhibited satisfactory Inconel 718 (In718) retention within the Ni matrix due to the highly ductile binder phase necessary for fabrication. The characterization of the coating microstructures was implemented by means of X-ray diffraction, electron microscopy, energy-dispersive X-ray spectroscopy, and microhardness testing. In addition, the erosion resistance of both coatings was evaluated by performing cavitation erosion tests, with the analysis of the eroded surfaces revealing different erosion mechanisms for each coating. The results demonstrated the efficiency of the cold spray technique for use in the production of metal-metal matrix composite coatings and the potential of In718 use in applications which demand enhanced cavitation erosion resistance.",
publisher = "Elsevier",
journal = "Surface and Coatings Technology",
title = "Microstructure and cavitation erosion performance of nickel-Inconel 718 composite coatings produced with cold spray",
volume = "382",
pages = "125195",
doi = "10.1016/j.surfcoat.2019.125195"
}

Kazasidis, M., Yin, S., Cassidy, J., Volkov-Husović, T., Vlahović, M., Martinović, S., Kyriakopoulou, E.,& Lupoi, R.. (2020). Microstructure and cavitation erosion performance of nickel-Inconel 718 composite coatings produced with cold spray. in Surface and Coatings Technology
Elsevier., 382, 125195.
https://doi.org/10.1016/j.surfcoat.2019.125195

Kazasidis M, Yin S, Cassidy J, Volkov-Husović T, Vlahović M, Martinović S, Kyriakopoulou E, Lupoi R. Microstructure and cavitation erosion performance of nickel-Inconel 718 composite coatings produced with cold spray. in Surface and Coatings Technology. 2020;382:125195.
doi:10.1016/j.surfcoat.2019.125195 .

Kazasidis, Marios, Yin, Shuo, Cassidy, Jonathan, Volkov-Husović, Tatjana, Vlahović, Milica, Martinović, Sanja, Kyriakopoulou, Elena, Lupoi, Rocco, "Microstructure and cavitation erosion performance of nickel-Inconel 718 composite coatings produced with cold spray" in Surface and Coatings Technology, 382 (2020):125195,
https://doi.org/10.1016/j.surfcoat.2019.125195 . .

TY  - JOUR
AU  - Kazasidis, Marios
AU  - Yin, Shuo
AU  - Cassidy, Jonathan
AU  - Volkov-Husović, Tatjana
AU  - Vlahović, Milica
AU  - Martinović, Sanja
AU  - Kyriakopoulou, Elena
AU  - Lupoi, Rocco
PY  - 2020
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3274
AB  - The cold spray technique was employed in this study to produce pure nickel (Ni) and nickel-Inconel 718 powder deposits on duplex stainless steel substrates. High quality coatings were manufactured using nitrogen as the propellant gas. The coatings exhibited satisfactory Inconel 718 (In718) retention within the Ni matrix due to the highly ductile binder phase necessary for fabrication. The characterization of the coating microstructures was implemented by means of X-ray diffraction, electron microscopy, energy-dispersive X-ray spectroscopy, and microhardness testing. In addition, the erosion resistance of both coatings was evaluated by performing cavitation erosion tests, with the analysis of the eroded surfaces revealing different erosion mechanisms for each coating. The results demonstrated the efficiency of the cold spray technique for use in the production of metal-metal matrix composite coatings and the potential of In718 use in applications which demand enhanced cavitation erosion resistance.
PB  - Elsevier
T2  - Surface and Coatings Technology
T1  - Microstructure and cavitation erosion performance of nickel-Inconel 718 composite coatings produced with cold spray
VL  - 382
SP  - 125195
DO  - 10.1016/j.surfcoat.2019.125195
ER  - 

@article{
author = "Kazasidis, Marios and Yin, Shuo and Cassidy, Jonathan and Volkov-Husović, Tatjana and Vlahović, Milica and Martinović, Sanja and Kyriakopoulou, Elena and Lupoi, Rocco",
year = "2020",
abstract = "The cold spray technique was employed in this study to produce pure nickel (Ni) and nickel-Inconel 718 powder deposits on duplex stainless steel substrates. High quality coatings were manufactured using nitrogen as the propellant gas. The coatings exhibited satisfactory Inconel 718 (In718) retention within the Ni matrix due to the highly ductile binder phase necessary for fabrication. The characterization of the coating microstructures was implemented by means of X-ray diffraction, electron microscopy, energy-dispersive X-ray spectroscopy, and microhardness testing. In addition, the erosion resistance of both coatings was evaluated by performing cavitation erosion tests, with the analysis of the eroded surfaces revealing different erosion mechanisms for each coating. The results demonstrated the efficiency of the cold spray technique for use in the production of metal-metal matrix composite coatings and the potential of In718 use in applications which demand enhanced cavitation erosion resistance.",
publisher = "Elsevier",
journal = "Surface and Coatings Technology",
title = "Microstructure and cavitation erosion performance of nickel-Inconel 718 composite coatings produced with cold spray",
volume = "382",
pages = "125195",
doi = "10.1016/j.surfcoat.2019.125195"
}

Kazasidis, M., Yin, S., Cassidy, J., Volkov-Husović, T., Vlahović, M., Martinović, S., Kyriakopoulou, E.,& Lupoi, R.. (2020). Microstructure and cavitation erosion performance of nickel-Inconel 718 composite coatings produced with cold spray. in Surface and Coatings Technology
Elsevier., 382, 125195.
https://doi.org/10.1016/j.surfcoat.2019.125195

Kazasidis M, Yin S, Cassidy J, Volkov-Husović T, Vlahović M, Martinović S, Kyriakopoulou E, Lupoi R. Microstructure and cavitation erosion performance of nickel-Inconel 718 composite coatings produced with cold spray. in Surface and Coatings Technology. 2020;382:125195.
doi:10.1016/j.surfcoat.2019.125195 .

Kazasidis, Marios, Yin, Shuo, Cassidy, Jonathan, Volkov-Husović, Tatjana, Vlahović, Milica, Martinović, Sanja, Kyriakopoulou, Elena, Lupoi, Rocco, "Microstructure and cavitation erosion performance of nickel-Inconel 718 composite coatings produced with cold spray" in Surface and Coatings Technology, 382 (2020):125195,
https://doi.org/10.1016/j.surfcoat.2019.125195 . .

TY  - JOUR
AU  - Kokunešoski, Maja
AU  - Stanković, Miroslav
AU  - Vuković, Marina
AU  - Majstorović, Jelena
AU  - Šaponjić, Djordje
AU  - Ilić, Svetlana
AU  - Šaponjić, Aleksandra
PY  - 2020
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/4047
AB  - Macroporous silica ceramic was obtained using clay and diatomite. Boric acid as a low-cost additive in the amount of 1 wt% was used. These porous materials were obtained at low forming pressure (40-80 MPa) and lower sintering temperature (850-1300 ºC) for 4h in air. The influence of boric acid, forming pressure, and sintering temperature on the microstructure, porosity parameters, and mechanical properties of obtained porous monoliths were investigated. As-received and the modified samples were characterized by X-ray diffraction, FTIR, SEM, and mercury porosimetry measurements. As for modified clay and diatomite, they were pressed at 60 MPa and then sintered at 1150 ºC, obtaining porosities of about 10 % and 60 %, respectively. Both of the analyzed samples had the pore diameter in the range of macroporous materials. The pore diameters of clay samples are ranging from 0.1-10 μm, whereas the pore diameter of diatomite samples was slightly lower with values ranging from 0.05-5 μm. Modified diatomite samples have a lower Young modulus in comparison to modified clay samples.
PB  - Belgrade : Association for ETRAN Society
T2  - Science of Sintering
T1  - Macroporous monoliths based оn natural mineral sources, clay аnd diatomite
VL  - 52
IS  - 3
SP  - 339
EP  - 348
DO  - 10.2298/SOS2003339K
ER  - 

@article{
author = "Kokunešoski, Maja and Stanković, Miroslav and Vuković, Marina and Majstorović, Jelena and Šaponjić, Djordje and Ilić, Svetlana and Šaponjić, Aleksandra",
year = "2020",
abstract = "Macroporous silica ceramic was obtained using clay and diatomite. Boric acid as a low-cost additive in the amount of 1 wt% was used. These porous materials were obtained at low forming pressure (40-80 MPa) and lower sintering temperature (850-1300 ºC) for 4h in air. The influence of boric acid, forming pressure, and sintering temperature on the microstructure, porosity parameters, and mechanical properties of obtained porous monoliths were investigated. As-received and the modified samples were characterized by X-ray diffraction, FTIR, SEM, and mercury porosimetry measurements. As for modified clay and diatomite, they were pressed at 60 MPa and then sintered at 1150 ºC, obtaining porosities of about 10 % and 60 %, respectively. Both of the analyzed samples had the pore diameter in the range of macroporous materials. The pore diameters of clay samples are ranging from 0.1-10 μm, whereas the pore diameter of diatomite samples was slightly lower with values ranging from 0.05-5 μm. Modified diatomite samples have a lower Young modulus in comparison to modified clay samples.",
publisher = "Belgrade : Association for ETRAN Society",
journal = "Science of Sintering",
title = "Macroporous monoliths based оn natural mineral sources, clay аnd diatomite",
volume = "52",
number = "3",
pages = "339-348",
doi = "10.2298/SOS2003339K"
}

Kokunešoski, M., Stanković, M., Vuković, M., Majstorović, J., Šaponjić, D., Ilić, S.,& Šaponjić, A.. (2020). Macroporous monoliths based оn natural mineral sources, clay аnd diatomite. in Science of Sintering
Belgrade : Association for ETRAN Society., 52(3), 339-348.
https://doi.org/10.2298/SOS2003339K

Kokunešoski M, Stanković M, Vuković M, Majstorović J, Šaponjić D, Ilić S, Šaponjić A. Macroporous monoliths based оn natural mineral sources, clay аnd diatomite. in Science of Sintering. 2020;52(3):339-348.
doi:10.2298/SOS2003339K .

Kokunešoski, Maja, Stanković, Miroslav, Vuković, Marina, Majstorović, Jelena, Šaponjić, Djordje, Ilić, Svetlana, Šaponjić, Aleksandra, "Macroporous monoliths based оn natural mineral sources, clay аnd diatomite" in Science of Sintering, 52, no. 3 (2020):339-348,
https://doi.org/10.2298/SOS2003339K . .

TY  - CONF
AU  - Vlahović, Milica
AU  - Martinović, Sanja
AU  - Stević, Zoran
AU  - Savić, Aleksandar R.
AU  - Volkov Husović, Tatjana
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/5948
AB  - Establishing a wind park presents a complex enterprise, which involves numerous activities, often impossible to synchronize and drive into the appropriate time-frame. Therefore, in some cases, based on reasonable suspicion, a concern rises regarding the quality of already built components of structures. In such cases, the launch of suitable assessment procedures is required. Stand-ards then define proper methods of in-situ assessment of concrete quality. Statistical methods are implemented in the analysis of the concrete components following the strict rules which, if executed correctly by the well-trained personnel of accredited institutions, provide exact and valid insight in the situation. This paper aspires to describe such procedure on the basis of thorough in-situ investigation and subsequent analysis. In this study, a large number of 255 core samples were taken from 17 wind tower concrete structure elements – foundations (out of 57 wind towers in total), and the compressive strength of already placed concrete was evaluated based on this set of results. The compressive strength is proved to be a good parameter for evaluating other aspects of concrete quality, mechanical properties, and durability.
PB  - Beograd : Savez mašinskih i elektrotehničkih inženjera i tehničara Srbije - SMEITS
PB  - Beograd : Društvo za obnovljive izvore električne energije
C3  - Proceedings - 7th International Conference on Renewable Electrical Power Sources-MKOIEE, October 17–18, 2019, Belgrade, Serbia
T1  - Examining erosion resistance of ceramics for electrical engineering applications
SP  - 25
EP  - 30
UR  - https://hdl.handle.net/21.15107/rcub_cer_5948
ER  - 

@conference{
author = "Vlahović, Milica and Martinović, Sanja and Stević, Zoran and Savić, Aleksandar R. and Volkov Husović, Tatjana",
year = "2019",
abstract = "Establishing a wind park presents a complex enterprise, which involves numerous activities, often impossible to synchronize and drive into the appropriate time-frame. Therefore, in some cases, based on reasonable suspicion, a concern rises regarding the quality of already built components of structures. In such cases, the launch of suitable assessment procedures is required. Stand-ards then define proper methods of in-situ assessment of concrete quality. Statistical methods are implemented in the analysis of the concrete components following the strict rules which, if executed correctly by the well-trained personnel of accredited institutions, provide exact and valid insight in the situation. This paper aspires to describe such procedure on the basis of thorough in-situ investigation and subsequent analysis. In this study, a large number of 255 core samples were taken from 17 wind tower concrete structure elements – foundations (out of 57 wind towers in total), and the compressive strength of already placed concrete was evaluated based on this set of results. The compressive strength is proved to be a good parameter for evaluating other aspects of concrete quality, mechanical properties, and durability.",
publisher = "Beograd : Savez mašinskih i elektrotehničkih inženjera i tehničara Srbije - SMEITS, Beograd : Društvo za obnovljive izvore električne energije",
journal = "Proceedings - 7th International Conference on Renewable Electrical Power Sources-MKOIEE, October 17–18, 2019, Belgrade, Serbia",
title = "Examining erosion resistance of ceramics for electrical engineering applications",
pages = "25-30",
url = "https://hdl.handle.net/21.15107/rcub_cer_5948"
}

Vlahović, M., Martinović, S., Stević, Z., Savić, A. R.,& Volkov Husović, T.. (2019). Examining erosion resistance of ceramics for electrical engineering applications. in Proceedings - 7th International Conference on Renewable Electrical Power Sources-MKOIEE, October 17–18, 2019, Belgrade, Serbia
Beograd : Savez mašinskih i elektrotehničkih inženjera i tehničara Srbije - SMEITS., 25-30.
https://hdl.handle.net/21.15107/rcub_cer_5948

Vlahović M, Martinović S, Stević Z, Savić AR, Volkov Husović T. Examining erosion resistance of ceramics for electrical engineering applications. in Proceedings - 7th International Conference on Renewable Electrical Power Sources-MKOIEE, October 17–18, 2019, Belgrade, Serbia. 2019;:25-30.
https://hdl.handle.net/21.15107/rcub_cer_5948 .

Vlahović, Milica, Martinović, Sanja, Stević, Zoran, Savić, Aleksandar R., Volkov Husović, Tatjana, "Examining erosion resistance of ceramics for electrical engineering applications" in Proceedings - 7th International Conference on Renewable Electrical Power Sources-MKOIEE, October 17–18, 2019, Belgrade, Serbia (2019):25-30,
https://hdl.handle.net/21.15107/rcub_cer_5948 .

TY  - CONF
AU  - Savić, Aleksandar R.
AU  - Stević, Zoran
AU  - Martinović, Sanja
AU  - Vlahović, Milica
AU  - Volkov Husović, Tatjana
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/5947
AB  - In this research, two non-destructive testing (NDT) methods, thermal vision analysis and image analysis, were implemented for monitoring the surface changes- erosion of mullite-based ceramic samples in conditions of cavitation exposure. Thermal imaging analysis was focused on determining the temperature line profile at the end of the cavitation experiment. Image analysis is a powerful tool for the quantification of degradation level caused by different impacts and conditions. Based on the results of the image analysis, the degradation level during the testing was determined, as well as number of formed pits with their characteristics (average diameter and area). The results performed by both methods were discussed in order to obtain the optimal procedure that should be followed for estimating degradation caused by cavitation erosion.
PB  - Beograd : Savez mašinskih i elektrotehničkih inženjera i tehničara Srbije - SMEITS
PB  - Beograd : Društvo za obnovljive izvore električne energije
C3  - Proceedings - 7th International Conference on Renewable Electrical Power Sources-MKOIEE, October 17–18, 2019, Belgrade, Serbia
T1  - Quantitative and qualitative analysis of concrete elements in wind park
SP  - 15
EP  - 24
UR  - https://hdl.handle.net/21.15107/rcub_cer_5947
ER  - 

@conference{
author = "Savić, Aleksandar R. and Stević, Zoran and Martinović, Sanja and Vlahović, Milica and Volkov Husović, Tatjana",
year = "2019",
abstract = "In this research, two non-destructive testing (NDT) methods, thermal vision analysis and image analysis, were implemented for monitoring the surface changes- erosion of mullite-based ceramic samples in conditions of cavitation exposure. Thermal imaging analysis was focused on determining the temperature line profile at the end of the cavitation experiment. Image analysis is a powerful tool for the quantification of degradation level caused by different impacts and conditions. Based on the results of the image analysis, the degradation level during the testing was determined, as well as number of formed pits with their characteristics (average diameter and area). The results performed by both methods were discussed in order to obtain the optimal procedure that should be followed for estimating degradation caused by cavitation erosion.",
publisher = "Beograd : Savez mašinskih i elektrotehničkih inženjera i tehničara Srbije - SMEITS, Beograd : Društvo za obnovljive izvore električne energije",
journal = "Proceedings - 7th International Conference on Renewable Electrical Power Sources-MKOIEE, October 17–18, 2019, Belgrade, Serbia",
title = "Quantitative and qualitative analysis of concrete elements in wind park",
pages = "15-24",
url = "https://hdl.handle.net/21.15107/rcub_cer_5947"
}

Savić, A. R., Stević, Z., Martinović, S., Vlahović, M.,& Volkov Husović, T.. (2019). Quantitative and qualitative analysis of concrete elements in wind park. in Proceedings - 7th International Conference on Renewable Electrical Power Sources-MKOIEE, October 17–18, 2019, Belgrade, Serbia
Beograd : Savez mašinskih i elektrotehničkih inženjera i tehničara Srbije - SMEITS., 15-24.
https://hdl.handle.net/21.15107/rcub_cer_5947

Savić AR, Stević Z, Martinović S, Vlahović M, Volkov Husović T. Quantitative and qualitative analysis of concrete elements in wind park. in Proceedings - 7th International Conference on Renewable Electrical Power Sources-MKOIEE, October 17–18, 2019, Belgrade, Serbia. 2019;:15-24.
https://hdl.handle.net/21.15107/rcub_cer_5947 .

Savić, Aleksandar R., Stević, Zoran, Martinović, Sanja, Vlahović, Milica, Volkov Husović, Tatjana, "Quantitative and qualitative analysis of concrete elements in wind park" in Proceedings - 7th International Conference on Renewable Electrical Power Sources-MKOIEE, October 17–18, 2019, Belgrade, Serbia (2019):15-24,
https://hdl.handle.net/21.15107/rcub_cer_5947 .

TY  - JOUR
AU  - Živković, Ljiljana S.
AU  - Jegdić, Bore
AU  - Andrić, Velibor
AU  - Rhee, Kyong-Yop
AU  - Bajat, Jelena
AU  - Mišković-Stanković, Vesna
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3060
AB  - In this work an attempt was made to produce epoxy coating doped with ceria (CeO2) and/or zirconia (ZrO2) nanoparticles, in single step electrophoretric deposition process. Deposition was carried out on AA6060 cataforetically from epoxy resin suspension containing synthesized stable aqueous colloidal dispersions (sols) of CeO2 and ZrO2. The influence of ceria and zirconia nanoparticles on the physicochemical characteristics of epoxy coatings was evaluated by energy dispersive X-ray fluorescence spectroscopy, X-ray photoelectron spectroscopy, field-emission scanning electron microscopy, Fourier-transform infrared spectroscopy, thermogravimetric analysis and adhesion measurements, while their corrosion stability during immersion in 0.5 M NaCl solution was monitored by electrochemical impedance spectroscopy. All ceria and/or zirconia containing coatings showed better corrosion stability and adhesion than pure epoxy coating, while between doped epoxy coatings one with CeO2/ZrO2 exhhibited the greatest values of charge-transfer resistance due to synergetic effect of both types of added nanoparticles.
PB  - Elsevier
T2  - Progress in Organic Coatings
T1  - The effect of ceria and zirconia nanoparticles on the corrosion behaviour of cataphoretic epoxy coatings on AA6060 alloy
SP  - 105219
DO  - 10.1016/j.porgcoat.2019.105219
ER  - 

@article{
author = "Živković, Ljiljana S. and Jegdić, Bore and Andrić, Velibor and Rhee, Kyong-Yop and Bajat, Jelena and Mišković-Stanković, Vesna",
year = "2019",
abstract = "In this work an attempt was made to produce epoxy coating doped with ceria (CeO2) and/or zirconia (ZrO2) nanoparticles, in single step electrophoretric deposition process. Deposition was carried out on AA6060 cataforetically from epoxy resin suspension containing synthesized stable aqueous colloidal dispersions (sols) of CeO2 and ZrO2. The influence of ceria and zirconia nanoparticles on the physicochemical characteristics of epoxy coatings was evaluated by energy dispersive X-ray fluorescence spectroscopy, X-ray photoelectron spectroscopy, field-emission scanning electron microscopy, Fourier-transform infrared spectroscopy, thermogravimetric analysis and adhesion measurements, while their corrosion stability during immersion in 0.5 M NaCl solution was monitored by electrochemical impedance spectroscopy. All ceria and/or zirconia containing coatings showed better corrosion stability and adhesion than pure epoxy coating, while between doped epoxy coatings one with CeO2/ZrO2 exhhibited the greatest values of charge-transfer resistance due to synergetic effect of both types of added nanoparticles.",
publisher = "Elsevier",
journal = "Progress in Organic Coatings",
title = "The effect of ceria and zirconia nanoparticles on the corrosion behaviour of cataphoretic epoxy coatings on AA6060 alloy",
pages = "105219",
doi = "10.1016/j.porgcoat.2019.105219"
}

Živković, L. S., Jegdić, B., Andrić, V., Rhee, K., Bajat, J.,& Mišković-Stanković, V.. (2019). The effect of ceria and zirconia nanoparticles on the corrosion behaviour of cataphoretic epoxy coatings on AA6060 alloy. in Progress in Organic Coatings
Elsevier., 105219.
https://doi.org/10.1016/j.porgcoat.2019.105219

Živković LS, Jegdić B, Andrić V, Rhee K, Bajat J, Mišković-Stanković V. The effect of ceria and zirconia nanoparticles on the corrosion behaviour of cataphoretic epoxy coatings on AA6060 alloy. in Progress in Organic Coatings. 2019;:105219.
doi:10.1016/j.porgcoat.2019.105219 .

Živković, Ljiljana S., Jegdić, Bore, Andrić, Velibor, Rhee, Kyong-Yop, Bajat, Jelena, Mišković-Stanković, Vesna, "The effect of ceria and zirconia nanoparticles on the corrosion behaviour of cataphoretic epoxy coatings on AA6060 alloy" in Progress in Organic Coatings (2019):105219,
https://doi.org/10.1016/j.porgcoat.2019.105219 . .

TY  - JOUR
AU  - Čairović, Aleksandra D.
AU  - Stanimirović, Dragan D.
AU  - Krajnović, Tamara T.
AU  - Dojčinović, Biljana
AU  - Maksimović, Vesna M.
AU  - Cvijović-Alagić, Ivana Lj.
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/2993
AB  - The biological quality and chemical composition of alloys used in dental practice change during heat treatment.
Often the residues of the previous cast are not disposed of but are reused and recycled until consumed. Thus, manufactured dental restorations have modified biological quality and chemical composition, and compromised biocompatibility. The aim of this study was to investigate the influence of repeated casting on the cytotoxicity of the silver-palladium (Ag-Pd) alloy. Our results showed that repeated casting of the Ag-Pd dental alloy affected its biocompatibility by promoting toxicity against transformed fibroblasts in a contact-independent manner. A strong decrease in cell proliferation, induction of senescence and massive cell death were observed in cultures exposed only to a medium previously incubated with dental alloy samples. The obtained data indicated that toxicity mediated by the accumulation of the Ag, Pd, Cu and Zn cations released from the Ag-Pd material was enhanced by recasting. The induction of cell senescence and subsequent apoptotic
and necrotic death were accompanied by amplified intracellular production of reactive oxygen and nitrogen species, suggesting their involvement in the cell destruction process. Therefore, compromised biocompatibility after recasting with the Ag-Pd alloy can be the cause of serious local cell destruction, as observed in clinical practice.
PB  - Serbian Biological Society
T2  - Archives of Biological Sciences
T1  - Recasting as a booster of Ag-Pd alloy cytotoxicity: induction of cell senescence prior to mass cell death
VL  - 71
IS  - 2
SP  - 347
EP  - 356
DO  - 10.2298/ABS190305017C
ER  - 

@article{
author = "Čairović, Aleksandra D. and Stanimirović, Dragan D. and Krajnović, Tamara T. and Dojčinović, Biljana and Maksimović, Vesna M. and Cvijović-Alagić, Ivana Lj.",
year = "2019",
abstract = "The biological quality and chemical composition of alloys used in dental practice change during heat treatment.
Often the residues of the previous cast are not disposed of but are reused and recycled until consumed. Thus, manufactured dental restorations have modified biological quality and chemical composition, and compromised biocompatibility. The aim of this study was to investigate the influence of repeated casting on the cytotoxicity of the silver-palladium (Ag-Pd) alloy. Our results showed that repeated casting of the Ag-Pd dental alloy affected its biocompatibility by promoting toxicity against transformed fibroblasts in a contact-independent manner. A strong decrease in cell proliferation, induction of senescence and massive cell death were observed in cultures exposed only to a medium previously incubated with dental alloy samples. The obtained data indicated that toxicity mediated by the accumulation of the Ag, Pd, Cu and Zn cations released from the Ag-Pd material was enhanced by recasting. The induction of cell senescence and subsequent apoptotic
and necrotic death were accompanied by amplified intracellular production of reactive oxygen and nitrogen species, suggesting their involvement in the cell destruction process. Therefore, compromised biocompatibility after recasting with the Ag-Pd alloy can be the cause of serious local cell destruction, as observed in clinical practice.",
publisher = "Serbian Biological Society",
journal = "Archives of Biological Sciences",
title = "Recasting as a booster of Ag-Pd alloy cytotoxicity: induction of cell senescence prior to mass cell death",
volume = "71",
number = "2",
pages = "347-356",
doi = "10.2298/ABS190305017C"
}

Čairović, A. D., Stanimirović, D. D., Krajnović, T. T., Dojčinović, B., Maksimović, V. M.,& Cvijović-Alagić, I. Lj.. (2019). Recasting as a booster of Ag-Pd alloy cytotoxicity: induction of cell senescence prior to mass cell death. in Archives of Biological Sciences
Serbian Biological Society., 71(2), 347-356.
https://doi.org/10.2298/ABS190305017C

Čairović AD, Stanimirović DD, Krajnović TT, Dojčinović B, Maksimović VM, Cvijović-Alagić IL. Recasting as a booster of Ag-Pd alloy cytotoxicity: induction of cell senescence prior to mass cell death. in Archives of Biological Sciences. 2019;71(2):347-356.
doi:10.2298/ABS190305017C .

Čairović, Aleksandra D., Stanimirović, Dragan D., Krajnović, Tamara T., Dojčinović, Biljana, Maksimović, Vesna M., Cvijović-Alagić, Ivana Lj., "Recasting as a booster of Ag-Pd alloy cytotoxicity: induction of cell senescence prior to mass cell death" in Archives of Biological Sciences, 71, no. 2 (2019):347-356,
https://doi.org/10.2298/ABS190305017C . .

TY  - JOUR
AU  - Matović, Ljiljana
AU  - Vukelić, Nikola
AU  - Jovanović, Uroš D.
AU  - Kumrić, Ksenija
AU  - Krstić, Jugoslav
AU  - Babić, Biljana M.
AU  - Đukić, Anđelka B.
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3858
AB  - Modified activated carbon cloth is prepared by mechanochemical modification of viscose rayon carbon cloth. The effects of different milling atmospheres, in the air and inert conditions, were investigated. Changes in kind and number of acidic and basic surface groups on the surface of activated carbon cloth, upon modification, as well as before and after the sorption of arsenic were determined. Higher number of basic groups responsible for the removal of arsenic ions was achieved by modification under inert conditions. Breakage and collapse of cylindrical fibers, decrease of particle sizes, change in the shape and consistency of the particles, as well as increase of microstructural disorder i.e. the loss of turbostratic structure occurred upon milling. pHPZC values increased from 4.46 to 5.04 and 5.77 after the air and inert milling, respectively. Adsorption followed pseudo second order kinetics with chemisorption as rate-controlling step. Langmuir isotherm best fit the equilibrium data and maximum adsorption capacity is 5.5 mg g−1 at a pH value close to 7.0, typical for groundwater. The mechanism of arsenic adsorption onto activated carbon cloth milled in inert atmosphere involved electrostatic and dispersive interactions between arsenic ions and carbon particles in wide pH range (from 2 to 10).
PB  - Elsevier
T2  - Arabian Journal of Chemistry
T1  - Mechanochemically improved surface properties of activated carbon cloth for the removal of As(V) from aqueous solutions
VL  - 12
IS  - 8
SP  - 4446
EP  - 4457
DO  - 10.1016/j.arabjc.2016.07.004
ER  - 

@article{
author = "Matović, Ljiljana and Vukelić, Nikola and Jovanović, Uroš D. and Kumrić, Ksenija and Krstić, Jugoslav and Babić, Biljana M. and Đukić, Anđelka B.",
year = "2019",
abstract = "Modified activated carbon cloth is prepared by mechanochemical modification of viscose rayon carbon cloth. The effects of different milling atmospheres, in the air and inert conditions, were investigated. Changes in kind and number of acidic and basic surface groups on the surface of activated carbon cloth, upon modification, as well as before and after the sorption of arsenic were determined. Higher number of basic groups responsible for the removal of arsenic ions was achieved by modification under inert conditions. Breakage and collapse of cylindrical fibers, decrease of particle sizes, change in the shape and consistency of the particles, as well as increase of microstructural disorder i.e. the loss of turbostratic structure occurred upon milling. pHPZC values increased from 4.46 to 5.04 and 5.77 after the air and inert milling, respectively. Adsorption followed pseudo second order kinetics with chemisorption as rate-controlling step. Langmuir isotherm best fit the equilibrium data and maximum adsorption capacity is 5.5 mg g−1 at a pH value close to 7.0, typical for groundwater. The mechanism of arsenic adsorption onto activated carbon cloth milled in inert atmosphere involved electrostatic and dispersive interactions between arsenic ions and carbon particles in wide pH range (from 2 to 10).",
publisher = "Elsevier",
journal = "Arabian Journal of Chemistry",
title = "Mechanochemically improved surface properties of activated carbon cloth for the removal of As(V) from aqueous solutions",
volume = "12",
number = "8",
pages = "4446-4457",
doi = "10.1016/j.arabjc.2016.07.004"
}

Matović, L., Vukelić, N., Jovanović, U. D., Kumrić, K., Krstić, J., Babić, B. M.,& Đukić, A. B.. (2019). Mechanochemically improved surface properties of activated carbon cloth for the removal of As(V) from aqueous solutions. in Arabian Journal of Chemistry
Elsevier., 12(8), 4446-4457.
https://doi.org/10.1016/j.arabjc.2016.07.004

Matović L, Vukelić N, Jovanović UD, Kumrić K, Krstić J, Babić BM, Đukić AB. Mechanochemically improved surface properties of activated carbon cloth for the removal of As(V) from aqueous solutions. in Arabian Journal of Chemistry. 2019;12(8):4446-4457.
doi:10.1016/j.arabjc.2016.07.004 .

Matović, Ljiljana, Vukelić, Nikola, Jovanović, Uroš D., Kumrić, Ksenija, Krstić, Jugoslav, Babić, Biljana M., Đukić, Anđelka B., "Mechanochemically improved surface properties of activated carbon cloth for the removal of As(V) from aqueous solutions" in Arabian Journal of Chemistry, 12, no. 8 (2019):4446-4457,
https://doi.org/10.1016/j.arabjc.2016.07.004 . .

TY  - CHAP
AU  - Vlahović, Milica
AU  - Martinović, Sanja
AU  - Volkov Husović, Tatjana
PY  - 2019
UR  - https://novapublishers.com/shop/advances-in-chemistry-research-volume-58/
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/5955
AB  - Refractory castables, like all ceramic materials, contain numerous structural defects in the form of flaws, pores, microcracks, and impurities. These materials are often used in conditions of exposure to sudden and cyclical temperature changes, that is, to thermal shock. Such conditions can cause the creation of cracks in the material structure. Namely, the formation of new microcracks and the growth of those that already existed take place as a consequence of thermal shock. The decrease of mechanical strength as well as a general weakening and degradation of the material are also happening. This research evaluates the effects of thermal shock on high alumina low cement castable. The synthesized samples of one castable composition, based on alumina as an aggregate and calcium-aluminate cement, with the same cure conditions, were sintered at three different temperatures (1100°C, 1300°C, and 1600°C) with a dwell time of 3 hours. A water quench test was applied as an experimental method for thermal shock resistance testing. Morphological analysis of the samples before and during the testing was done. The changes in the material during thermal shock testing were monitored by destructive and non-destructive methods. Image analysis of the photographs of the samples' surfaces and SEM microphotographs of the sample cross-sections were applied to monitor degradation at the surface and inside the bulk. Ultrasonic measurements were used for monitoring internal degradation and elastic properties. Both non-destructive methods also served for homogeneity analysis. Overall material degradation was determined by measuring the mechanical strength of the samples using a classic method according to the standardized procedure. According to the results of performed experiments and analyses, it is evident that during the thermal shock, the surface and interior of the samples sintered at 1600°C behave differently compared with those sintered at 1100°C and 1300°C. The investigations have revealed that all three series of the obtained alumina-based refractory castables displayed high resistance to thermal shock since they withstood more than 40 thermal shock cycles without cracking and with a level of degradation below 50%, even under 25%. The samples sintered at 1300°C exhibited the best thermal shock resistance with more than 110 cycles without cracking. This behavior recommends that all three series of high alumina low cement castables can be effectively used in conditions that require good thermal stability.
PB  - Nova Science
T2  - Advances in Chemistry Research
T1  - Investigation of thermal shock resistance in alumina based refractory castables
VL  - 58
SP  - 183
EP  - 241
UR  - https://hdl.handle.net/21.15107/rcub_cer_5955
ER  - 

@inbook{
author = "Vlahović, Milica and Martinović, Sanja and Volkov Husović, Tatjana",
year = "2019",
abstract = "Refractory castables, like all ceramic materials, contain numerous structural defects in the form of flaws, pores, microcracks, and impurities. These materials are often used in conditions of exposure to sudden and cyclical temperature changes, that is, to thermal shock. Such conditions can cause the creation of cracks in the material structure. Namely, the formation of new microcracks and the growth of those that already existed take place as a consequence of thermal shock. The decrease of mechanical strength as well as a general weakening and degradation of the material are also happening. This research evaluates the effects of thermal shock on high alumina low cement castable. The synthesized samples of one castable composition, based on alumina as an aggregate and calcium-aluminate cement, with the same cure conditions, were sintered at three different temperatures (1100°C, 1300°C, and 1600°C) with a dwell time of 3 hours. A water quench test was applied as an experimental method for thermal shock resistance testing. Morphological analysis of the samples before and during the testing was done. The changes in the material during thermal shock testing were monitored by destructive and non-destructive methods. Image analysis of the photographs of the samples' surfaces and SEM microphotographs of the sample cross-sections were applied to monitor degradation at the surface and inside the bulk. Ultrasonic measurements were used for monitoring internal degradation and elastic properties. Both non-destructive methods also served for homogeneity analysis. Overall material degradation was determined by measuring the mechanical strength of the samples using a classic method according to the standardized procedure. According to the results of performed experiments and analyses, it is evident that during the thermal shock, the surface and interior of the samples sintered at 1600°C behave differently compared with those sintered at 1100°C and 1300°C. The investigations have revealed that all three series of the obtained alumina-based refractory castables displayed high resistance to thermal shock since they withstood more than 40 thermal shock cycles without cracking and with a level of degradation below 50%, even under 25%. The samples sintered at 1300°C exhibited the best thermal shock resistance with more than 110 cycles without cracking. This behavior recommends that all three series of high alumina low cement castables can be effectively used in conditions that require good thermal stability.",
publisher = "Nova Science",
journal = "Advances in Chemistry Research",
booktitle = "Investigation of thermal shock resistance in alumina based refractory castables",
volume = "58",
pages = "183-241",
url = "https://hdl.handle.net/21.15107/rcub_cer_5955"
}

Vlahović, M., Martinović, S.,& Volkov Husović, T.. (2019). Investigation of thermal shock resistance in alumina based refractory castables. in Advances in Chemistry Research
Nova Science., 58, 183-241.
https://hdl.handle.net/21.15107/rcub_cer_5955

Vlahović M, Martinović S, Volkov Husović T. Investigation of thermal shock resistance in alumina based refractory castables. in Advances in Chemistry Research. 2019;58:183-241.
https://hdl.handle.net/21.15107/rcub_cer_5955 .

Vlahović, Milica, Martinović, Sanja, Volkov Husović, Tatjana, "Investigation of thermal shock resistance in alumina based refractory castables" in Advances in Chemistry Research, 58 (2019):183-241,
https://hdl.handle.net/21.15107/rcub_cer_5955 .

TY  - JOUR
AU  - Mićović, Dragana
AU  - Pagnacco, Maja
AU  - Banković, Predrag
AU  - Maletaškić, Jelena
AU  - Matović, Branko
AU  - Djokič, Veljko
AU  - Stojmenović, Marija
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3246
AB  - Potential non-toxic pink and red ceramic pigments based on CeO2 were successfully synthesized by selfpropagating room temperaturemethod and thermally treated at 600, 900 and 1200°C for 15min. The structure, morphology and optical properties, as well as thermal stability of Ce1-xErxO2-δ and Ce1-xPrxO2-δ(x = 0.05) were examined. Single-phase composition of all obtained CeO2 pigments was confirmed using XRPD method and Raman spectroscopy and it was not dependent on temperature. The mechanism of structural behaviour was thoroughly examined using Raman and FTIR spectroscopy. Nanometric dimensions of the crystallites of all pigments were confirmed using XRPD, TEM and FE-SEM analysis. Colour properties were dependent on the temperature treatment, and their position in the chromaticity diagram was studied using UV/VIS spectrophotometry. Colour efficiency measurements were supplemented by colorimetric analysis. It is proved that all samples are thermally stable in the investigated temperature range (up to 1200°C), and their potential application as environmentally friendly pigments of desired colour is confirmed.
PB  - Faculty of Technology, University of Novi Sad
T2  - Processing and Application of Ceramics
T1  - The influence of short thermal treatment on structure, morphology and optical properties of Er and Pr doped ceria pigments: Comparative study
VL  - 13
IS  - 3
SP  - 310
EP  - 321
DO  - 10.2298/PAC1903310M
ER  - 

@article{
author = "Mićović, Dragana and Pagnacco, Maja and Banković, Predrag and Maletaškić, Jelena and Matović, Branko and Djokič, Veljko and Stojmenović, Marija",
year = "2019",
abstract = "Potential non-toxic pink and red ceramic pigments based on CeO2 were successfully synthesized by selfpropagating room temperaturemethod and thermally treated at 600, 900 and 1200°C for 15min. The structure, morphology and optical properties, as well as thermal stability of Ce1-xErxO2-δ and Ce1-xPrxO2-δ(x = 0.05) were examined. Single-phase composition of all obtained CeO2 pigments was confirmed using XRPD method and Raman spectroscopy and it was not dependent on temperature. The mechanism of structural behaviour was thoroughly examined using Raman and FTIR spectroscopy. Nanometric dimensions of the crystallites of all pigments were confirmed using XRPD, TEM and FE-SEM analysis. Colour properties were dependent on the temperature treatment, and their position in the chromaticity diagram was studied using UV/VIS spectrophotometry. Colour efficiency measurements were supplemented by colorimetric analysis. It is proved that all samples are thermally stable in the investigated temperature range (up to 1200°C), and their potential application as environmentally friendly pigments of desired colour is confirmed.",
publisher = "Faculty of Technology, University of Novi Sad",
journal = "Processing and Application of Ceramics",
title = "The influence of short thermal treatment on structure, morphology and optical properties of Er and Pr doped ceria pigments: Comparative study",
volume = "13",
number = "3",
pages = "310-321",
doi = "10.2298/PAC1903310M"
}

Mićović, D., Pagnacco, M., Banković, P., Maletaškić, J., Matović, B., Djokič, V.,& Stojmenović, M.. (2019). The influence of short thermal treatment on structure, morphology and optical properties of Er and Pr doped ceria pigments: Comparative study. in Processing and Application of Ceramics
Faculty of Technology, University of Novi Sad., 13(3), 310-321.
https://doi.org/10.2298/PAC1903310M

Mićović D, Pagnacco M, Banković P, Maletaškić J, Matović B, Djokič V, Stojmenović M. The influence of short thermal treatment on structure, morphology and optical properties of Er and Pr doped ceria pigments: Comparative study. in Processing and Application of Ceramics. 2019;13(3):310-321.
doi:10.2298/PAC1903310M .

Mićović, Dragana, Pagnacco, Maja, Banković, Predrag, Maletaškić, Jelena, Matović, Branko, Djokič, Veljko, Stojmenović, Marija, "The influence of short thermal treatment on structure, morphology and optical properties of Er and Pr doped ceria pigments: Comparative study" in Processing and Application of Ceramics, 13, no. 3 (2019):310-321,
https://doi.org/10.2298/PAC1903310M . .

TY  - CONF
AU  - Volkov Husović, Tatjana
AU  - Martinović, Sanja
AU  - Vlahović, Milica
AU  - Savić, Aleksandar R.
AU  - Stević, Zoran
PY  - 2018
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/5951
AB  - The quantities of component materials used for production of concrete are high on the
global scale, therefore alternative materials are experimented on, in order to replace the
natural ones. The possibility of using ground waste sulfur from the oil refining (petroleum)
industry as a filling component of self-compacting concrete is presented in the paper, based
on common concrete laboratory tests. The physical and mechanical properties of selfcompacting
concrete decrease to some extend due to use of ground sulfur, but this concrete
remains useful for some building applications.
PB  - Association for Promotion of Holistic Approach to Environment
C3  - Proceedings book - 1st International Conference “The Holistic Approach to Environment”, 13-14 September, 2018, Sisak, Croatia
T1  - Possible use of ground sulfur as petroleum industry byproduct in self-compacting concrete production
SP  - 784
EP  - 791
UR  - https://hdl.handle.net/21.15107/rcub_cer_5951
ER  - 

@conference{
author = "Volkov Husović, Tatjana and Martinović, Sanja and Vlahović, Milica and Savić, Aleksandar R. and Stević, Zoran",
year = "2018",
abstract = "The quantities of component materials used for production of concrete are high on the
global scale, therefore alternative materials are experimented on, in order to replace the
natural ones. The possibility of using ground waste sulfur from the oil refining (petroleum)
industry as a filling component of self-compacting concrete is presented in the paper, based
on common concrete laboratory tests. The physical and mechanical properties of selfcompacting
concrete decrease to some extend due to use of ground sulfur, but this concrete
remains useful for some building applications.",
publisher = "Association for Promotion of Holistic Approach to Environment",
journal = "Proceedings book - 1st International Conference “The Holistic Approach to Environment”, 13-14 September, 2018, Sisak, Croatia",
title = "Possible use of ground sulfur as petroleum industry byproduct in self-compacting concrete production",
pages = "784-791",
url = "https://hdl.handle.net/21.15107/rcub_cer_5951"
}

Volkov Husović, T., Martinović, S., Vlahović, M., Savić, A. R.,& Stević, Z.. (2018). Possible use of ground sulfur as petroleum industry byproduct in self-compacting concrete production. in Proceedings book - 1st International Conference “The Holistic Approach to Environment”, 13-14 September, 2018, Sisak, Croatia
Association for Promotion of Holistic Approach to Environment., 784-791.
https://hdl.handle.net/21.15107/rcub_cer_5951

Volkov Husović T, Martinović S, Vlahović M, Savić AR, Stević Z. Possible use of ground sulfur as petroleum industry byproduct in self-compacting concrete production. in Proceedings book - 1st International Conference “The Holistic Approach to Environment”, 13-14 September, 2018, Sisak, Croatia. 2018;:784-791.
https://hdl.handle.net/21.15107/rcub_cer_5951 .

Volkov Husović, Tatjana, Martinović, Sanja, Vlahović, Milica, Savić, Aleksandar R., Stević, Zoran, "Possible use of ground sulfur as petroleum industry byproduct in self-compacting concrete production" in Proceedings book - 1st International Conference “The Holistic Approach to Environment”, 13-14 September, 2018, Sisak, Croatia (2018):784-791,
https://hdl.handle.net/21.15107/rcub_cer_5951 .

TY  - CONF
AU  - Vlahović, Milica
AU  - Martinović, Sanja
AU  - Savić, Aleksandar R.
AU  - Stević, Zoran
AU  - Volkov Husović, Tatjana
PY  - 2018
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/5952
AB  - Mainly due to the strict global environmental regulations regarding the oil and gas
refining processes, which limit the maximum quantity of sulfur in combustibles, the
availability of waste sulfur has been considerably growing during the last decades and it is
evident that there will be a continuous abundant supply of waste sulfur in the future. Finding
new ways for waste sulfur consumption thus becomes very important. In this research,
possibility of using waste sulfur as a binding agent in concrete was analyzed and the
properties of the obtained sulfur polymer concrete in aggressive environments were examined
using destructive and non-destructive testing methods. Compressive strength changes were
insignificant. Ultrasonic measurements indicated significant homogeneity changes and slight
internal degradation. Based on the obtained results, the material with satisfying quality for
possible application in corrosive environment was produced.
PB  - Association for Promotion of Holistic Approach to Environment
C3  - Proceedings book - 1st International Conference “The Holistic Approach to Environment”, 13-14 September, 2018, Sisak, Croatia
T1  - Reuse of waste sulfur as a binding agent in concrete
SP  - 776
EP  - 783
UR  - https://hdl.handle.net/21.15107/rcub_cer_5952
ER  - 

@conference{
author = "Vlahović, Milica and Martinović, Sanja and Savić, Aleksandar R. and Stević, Zoran and Volkov Husović, Tatjana",
year = "2018",
abstract = "Mainly due to the strict global environmental regulations regarding the oil and gas
refining processes, which limit the maximum quantity of sulfur in combustibles, the
availability of waste sulfur has been considerably growing during the last decades and it is
evident that there will be a continuous abundant supply of waste sulfur in the future. Finding
new ways for waste sulfur consumption thus becomes very important. In this research,
possibility of using waste sulfur as a binding agent in concrete was analyzed and the
properties of the obtained sulfur polymer concrete in aggressive environments were examined
using destructive and non-destructive testing methods. Compressive strength changes were
insignificant. Ultrasonic measurements indicated significant homogeneity changes and slight
internal degradation. Based on the obtained results, the material with satisfying quality for
possible application in corrosive environment was produced.",
publisher = "Association for Promotion of Holistic Approach to Environment",
journal = "Proceedings book - 1st International Conference “The Holistic Approach to Environment”, 13-14 September, 2018, Sisak, Croatia",
title = "Reuse of waste sulfur as a binding agent in concrete",
pages = "776-783",
url = "https://hdl.handle.net/21.15107/rcub_cer_5952"
}

Vlahović, M., Martinović, S., Savić, A. R., Stević, Z.,& Volkov Husović, T.. (2018). Reuse of waste sulfur as a binding agent in concrete. in Proceedings book - 1st International Conference “The Holistic Approach to Environment”, 13-14 September, 2018, Sisak, Croatia
Association for Promotion of Holistic Approach to Environment., 776-783.
https://hdl.handle.net/21.15107/rcub_cer_5952

Vlahović M, Martinović S, Savić AR, Stević Z, Volkov Husović T. Reuse of waste sulfur as a binding agent in concrete. in Proceedings book - 1st International Conference “The Holistic Approach to Environment”, 13-14 September, 2018, Sisak, Croatia. 2018;:776-783.
https://hdl.handle.net/21.15107/rcub_cer_5952 .

Vlahović, Milica, Martinović, Sanja, Savić, Aleksandar R., Stević, Zoran, Volkov Husović, Tatjana, "Reuse of waste sulfur as a binding agent in concrete" in Proceedings book - 1st International Conference “The Holistic Approach to Environment”, 13-14 September, 2018, Sisak, Croatia (2018):776-783,
https://hdl.handle.net/21.15107/rcub_cer_5952 .

TY  - CONF
AU  - Savić, Aleksandar R.
AU  - Martinović, Sanja
AU  - Vlahović, Milica
AU  - Stević, Zoran
AU  - Volkov Husović, Tatjana
PY  - 2018
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/5965
AB  - Self-compacting concrete (SCC) typically contains a certain content of very fine mineral fillers such as limestone powder. The idea of this study was to partially replace limestone with elemental waste sulfur since it is hydrophobic, insoluble in water and therefore chemically inert in concrete mixtures. Properties of conventional SCC with limestone and several compositions with different sulfur content were compared. Hardened concrete was tested for compressive, flexural, and adhesion strengths, dynamic elasticity modulus, specific electrical resistance, density, microstructure, and infra-red thermography. Results showed a slight decline in compressive, flexural, and adhesion strengths as well as in dynamic elasticity modulus. Specific electrical resistance and density were higher for samples with sulfur. SEM analysis indicated a slight porosity increase for the sample with sulfur. Infrared thermography was applied as a fast method for detecting internal deformations. Having in mind that all properties should remain or improve in case of waste valorization and the criteria should be set to satisfy requirements for SCC, this study proved that all mixtures can be used for certain structural applications.
PB  - Union of Mechanical and Electrical Engineers and Technicains of Serbia
PB  - Society for Renewable Electrical Power Sources
C3  - Proceedings - 6th International Conference on Renewable Electrical Power Sources-MKOIEE, October 11-12, 2018, Belgrade, Serbia
T1  - Valorization of waste sulfur in synthesis of eco-friendly self-compacting concrete
SP  - 221
EP  - 228
UR  - https://hdl.handle.net/21.15107/rcub_cer_5965
ER  - 

@conference{
author = "Savić, Aleksandar R. and Martinović, Sanja and Vlahović, Milica and Stević, Zoran and Volkov Husović, Tatjana",
year = "2018",
abstract = "Self-compacting concrete (SCC) typically contains a certain content of very fine mineral fillers such as limestone powder. The idea of this study was to partially replace limestone with elemental waste sulfur since it is hydrophobic, insoluble in water and therefore chemically inert in concrete mixtures. Properties of conventional SCC with limestone and several compositions with different sulfur content were compared. Hardened concrete was tested for compressive, flexural, and adhesion strengths, dynamic elasticity modulus, specific electrical resistance, density, microstructure, and infra-red thermography. Results showed a slight decline in compressive, flexural, and adhesion strengths as well as in dynamic elasticity modulus. Specific electrical resistance and density were higher for samples with sulfur. SEM analysis indicated a slight porosity increase for the sample with sulfur. Infrared thermography was applied as a fast method for detecting internal deformations. Having in mind that all properties should remain or improve in case of waste valorization and the criteria should be set to satisfy requirements for SCC, this study proved that all mixtures can be used for certain structural applications.",
publisher = "Union of Mechanical and Electrical Engineers and Technicains of Serbia, Society for Renewable Electrical Power Sources",
journal = "Proceedings - 6th International Conference on Renewable Electrical Power Sources-MKOIEE, October 11-12, 2018, Belgrade, Serbia",
title = "Valorization of waste sulfur in synthesis of eco-friendly self-compacting concrete",
pages = "221-228",
url = "https://hdl.handle.net/21.15107/rcub_cer_5965"
}

Savić, A. R., Martinović, S., Vlahović, M., Stević, Z.,& Volkov Husović, T.. (2018). Valorization of waste sulfur in synthesis of eco-friendly self-compacting concrete. in Proceedings - 6th International Conference on Renewable Electrical Power Sources-MKOIEE, October 11-12, 2018, Belgrade, Serbia
Union of Mechanical and Electrical Engineers and Technicains of Serbia., 221-228.
https://hdl.handle.net/21.15107/rcub_cer_5965

Savić AR, Martinović S, Vlahović M, Stević Z, Volkov Husović T. Valorization of waste sulfur in synthesis of eco-friendly self-compacting concrete. in Proceedings - 6th International Conference on Renewable Electrical Power Sources-MKOIEE, October 11-12, 2018, Belgrade, Serbia. 2018;:221-228.
https://hdl.handle.net/21.15107/rcub_cer_5965 .

Savić, Aleksandar R., Martinović, Sanja, Vlahović, Milica, Stević, Zoran, Volkov Husović, Tatjana, "Valorization of waste sulfur in synthesis of eco-friendly self-compacting concrete" in Proceedings - 6th International Conference on Renewable Electrical Power Sources-MKOIEE, October 11-12, 2018, Belgrade, Serbia (2018):221-228,
https://hdl.handle.net/21.15107/rcub_cer_5965 .

TY  - CONF
AU  - Majstorović, Jelena
AU  - Martinović, Sanja
AU  - Vlahović, Milica
AU  - Dojčinović, Marina
AU  - Pavlović, Marko
AU  - Volkov Husović, Tatjana
PY  - 2018
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/6012
AB  - Samples based on talc with 15 % of zeolite from Zlatokop, Serbia, sintered at 1200 ºC were prepared and tested in condition of cavitation erosion. The ultrasonic vibratory cavitation set up with a stationary specimen was used. Mass loss was measured and degradation level of the samples using image analysis and Young modulus of elasticity was monitored. Obtained results showed good resistance to the cavitation erosion giving the possibility of future application in different conditions where cavitation erosion is expected.
PB  - Bosnia and Herzegovina : University of Zenica,  Faculty of metallurgy and technology
C3  - Proceedings - 12th Scientific/Research Symposium With International Participation “Metallic and Nonmetallic Materials: Production-properties-application“, , April 19th – 20th 2018., Vlašić, Bosnia and Herzegovina
T1  - Cavitation of refractory samples based on talc and zeolite from Zlatokop
SP  - 230
EP  - 233
UR  - https://hdl.handle.net/21.15107/rcub_cer_6012
ER  - 

@conference{
author = "Majstorović, Jelena and Martinović, Sanja and Vlahović, Milica and Dojčinović, Marina and Pavlović, Marko and Volkov Husović, Tatjana",
year = "2018",
abstract = "Samples based on talc with 15 % of zeolite from Zlatokop, Serbia, sintered at 1200 ºC were prepared and tested in condition of cavitation erosion. The ultrasonic vibratory cavitation set up with a stationary specimen was used. Mass loss was measured and degradation level of the samples using image analysis and Young modulus of elasticity was monitored. Obtained results showed good resistance to the cavitation erosion giving the possibility of future application in different conditions where cavitation erosion is expected.",
publisher = "Bosnia and Herzegovina : University of Zenica,  Faculty of metallurgy and technology",
journal = "Proceedings - 12th Scientific/Research Symposium With International Participation “Metallic and Nonmetallic Materials: Production-properties-application“, , April 19th – 20th 2018., Vlašić, Bosnia and Herzegovina",
title = "Cavitation of refractory samples based on talc and zeolite from Zlatokop",
pages = "230-233",
url = "https://hdl.handle.net/21.15107/rcub_cer_6012"
}

Majstorović, J., Martinović, S., Vlahović, M., Dojčinović, M., Pavlović, M.,& Volkov Husović, T.. (2018). Cavitation of refractory samples based on talc and zeolite from Zlatokop. in Proceedings - 12th Scientific/Research Symposium With International Participation “Metallic and Nonmetallic Materials: Production-properties-application“, , April 19th – 20th 2018., Vlašić, Bosnia and Herzegovina
Bosnia and Herzegovina : University of Zenica,  Faculty of metallurgy and technology., 230-233.
https://hdl.handle.net/21.15107/rcub_cer_6012

Majstorović J, Martinović S, Vlahović M, Dojčinović M, Pavlović M, Volkov Husović T. Cavitation of refractory samples based on talc and zeolite from Zlatokop. in Proceedings - 12th Scientific/Research Symposium With International Participation “Metallic and Nonmetallic Materials: Production-properties-application“, , April 19th – 20th 2018., Vlašić, Bosnia and Herzegovina. 2018;:230-233.
https://hdl.handle.net/21.15107/rcub_cer_6012 .

Majstorović, Jelena, Martinović, Sanja, Vlahović, Milica, Dojčinović, Marina, Pavlović, Marko, Volkov Husović, Tatjana, "Cavitation of refractory samples based on talc and zeolite from Zlatokop" in Proceedings - 12th Scientific/Research Symposium With International Participation “Metallic and Nonmetallic Materials: Production-properties-application“, , April 19th – 20th 2018., Vlašić, Bosnia and Herzegovina (2018):230-233,
https://hdl.handle.net/21.15107/rcub_cer_6012 .

TY  - JOUR
AU  - Majstorović-Necković, Jelena B.
AU  - Pavlović, Marko D.
AU  - Dojčinović, Marina
AU  - Martinović, Sanja
AU  - Vlahović, Milica
AU  - Volkov-Husović, Tatjana
PY  - 2018
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/2281
AB  - Using domestic zeolite from Igroš as row material for ceramic samples for application in condition of cavitation erosion. Samples based on talc with 15 % of zeolite, from Igroš, sintered at 1200oC were used in this investigation. The ultrasonic vibratory cavitation set up with stacionary specimen was used. Mass loss was measured and degradation level of the samples using image analysis and Young modulus of elasticity. Obtained results showed good resistance of the sample to the cavitation erosion, which give the possibility for possible future application of ceramic samples based on talc and yeolite in different conditions where cavitation erosion is expected.
AB  - U radu su prezentirani rezultati istraživanja korišćenja domaćeg zeolita sa ležišta 'Igroš' za izradu keramičkih uzoraka i primenu u uslovima dejstva kavitacije. Za ispitivanja su korišćeni uzorci talka sa 15% zeolita iz domaćeg ležišta IGROŠ (Brus) sinterovani na 1200oC. Za određivanje otpornosti na dejstvo kavitacije korišćena je ultrazvučna vibraciona metoda sa stacionarnim uzorkom. Gubitak mase i nivo degradacije površine uzoraka praćeni su primenom analize slike i Jungovog modula elastičnosti. Rezultati ispitivanja pokazali su dobru otpornost keramike na dejstvo kavitacije na bazi talka i zeolita što ukazuje na mogućnost primene u različitim oblastima industrije gde se očekuje prisustvo razaranja pod dejstvom kavitacije.
PB  - Srbija : Savez inženjera i tehničara Srbije
T2  - Tehnika
T1  - Cavitation of refratory samples based on talc and domestic zeolite
T1  - Ispitivanje vatrostalnih uzoraka na bazi talka i domaćeg zeolita na dejstvo kavitacije
VL  - 73
IS  - 3
SP  - 364
EP  - 369
DO  - 10.5937/tehnika1803364M
ER  - 

@article{
author = "Majstorović-Necković, Jelena B. and Pavlović, Marko D. and Dojčinović, Marina and Martinović, Sanja and Vlahović, Milica and Volkov-Husović, Tatjana",
year = "2018",
abstract = "Using domestic zeolite from Igroš as row material for ceramic samples for application in condition of cavitation erosion. Samples based on talc with 15 % of zeolite, from Igroš, sintered at 1200oC were used in this investigation. The ultrasonic vibratory cavitation set up with stacionary specimen was used. Mass loss was measured and degradation level of the samples using image analysis and Young modulus of elasticity. Obtained results showed good resistance of the sample to the cavitation erosion, which give the possibility for possible future application of ceramic samples based on talc and yeolite in different conditions where cavitation erosion is expected., U radu su prezentirani rezultati istraživanja korišćenja domaćeg zeolita sa ležišta 'Igroš' za izradu keramičkih uzoraka i primenu u uslovima dejstva kavitacije. Za ispitivanja su korišćeni uzorci talka sa 15% zeolita iz domaćeg ležišta IGROŠ (Brus) sinterovani na 1200oC. Za određivanje otpornosti na dejstvo kavitacije korišćena je ultrazvučna vibraciona metoda sa stacionarnim uzorkom. Gubitak mase i nivo degradacije površine uzoraka praćeni su primenom analize slike i Jungovog modula elastičnosti. Rezultati ispitivanja pokazali su dobru otpornost keramike na dejstvo kavitacije na bazi talka i zeolita što ukazuje na mogućnost primene u različitim oblastima industrije gde se očekuje prisustvo razaranja pod dejstvom kavitacije.",
publisher = "Srbija : Savez inženjera i tehničara Srbije",
journal = "Tehnika",
title = "Cavitation of refratory samples based on talc and domestic zeolite, Ispitivanje vatrostalnih uzoraka na bazi talka i domaćeg zeolita na dejstvo kavitacije",
volume = "73",
number = "3",
pages = "364-369",
doi = "10.5937/tehnika1803364M"
}

Majstorović-Necković, J. B., Pavlović, M. D., Dojčinović, M., Martinović, S., Vlahović, M.,& Volkov-Husović, T.. (2018). Cavitation of refratory samples based on talc and domestic zeolite. in Tehnika
Srbija : Savez inženjera i tehničara Srbije., 73(3), 364-369.
https://doi.org/10.5937/tehnika1803364M

Majstorović-Necković JB, Pavlović MD, Dojčinović M, Martinović S, Vlahović M, Volkov-Husović T. Cavitation of refratory samples based on talc and domestic zeolite. in Tehnika. 2018;73(3):364-369.
doi:10.5937/tehnika1803364M .

Majstorović-Necković, Jelena B., Pavlović, Marko D., Dojčinović, Marina, Martinović, Sanja, Vlahović, Milica, Volkov-Husović, Tatjana, "Cavitation of refratory samples based on talc and domestic zeolite" in Tehnika, 73, no. 3 (2018):364-369,
https://doi.org/10.5937/tehnika1803364M . .

TY  - JOUR
AU  - Martinović, Sanja
AU  - Vlahović, Milica
AU  - Dojčinović, Marina
AU  - Pavlović, Marko
AU  - Volkov-Husović, Tatjana
PY  - 2018
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/2343
AB  - In this study the resistance of cordierite and zircon to the cavitation erosion was investigated with the aim of possible spreading their application. Cavitation erosion test was applied using standard ultrasonic vibratory set up with stationary sample. Weight loss and image analysis measurements including morphological analysis of the formed pits were used for monitoring degradation during the cavitation erosion testing. The obtained results were discussed in order to compare and analyze degradation mechanism and the resistance of the investigated materials to cavitation erosion. Cordierite sample underwent less serious degradation, characterized by continual forming of new pits, while zircon degradation progressed by growth and merging of already formed pits.
PB  - Elsevier
T2  - Materials Letters
T1  - Comparison of cavitation erosion behavior of cordierite and zircon based samples using image and morphological analyses
VL  - 220
SP  - 136
EP  - 139
DO  - 10.1016/j.matlet.2018.03.029
ER  - 

@article{
author = "Martinović, Sanja and Vlahović, Milica and Dojčinović, Marina and Pavlović, Marko and Volkov-Husović, Tatjana",
year = "2018",
abstract = "In this study the resistance of cordierite and zircon to the cavitation erosion was investigated with the aim of possible spreading their application. Cavitation erosion test was applied using standard ultrasonic vibratory set up with stationary sample. Weight loss and image analysis measurements including morphological analysis of the formed pits were used for monitoring degradation during the cavitation erosion testing. The obtained results were discussed in order to compare and analyze degradation mechanism and the resistance of the investigated materials to cavitation erosion. Cordierite sample underwent less serious degradation, characterized by continual forming of new pits, while zircon degradation progressed by growth and merging of already formed pits.",
publisher = "Elsevier",
journal = "Materials Letters",
title = "Comparison of cavitation erosion behavior of cordierite and zircon based samples using image and morphological analyses",
volume = "220",
pages = "136-139",
doi = "10.1016/j.matlet.2018.03.029"
}

Martinović, S., Vlahović, M., Dojčinović, M., Pavlović, M.,& Volkov-Husović, T.. (2018). Comparison of cavitation erosion behavior of cordierite and zircon based samples using image and morphological analyses. in Materials Letters
Elsevier., 220, 136-139.
https://doi.org/10.1016/j.matlet.2018.03.029

Martinović S, Vlahović M, Dojčinović M, Pavlović M, Volkov-Husović T. Comparison of cavitation erosion behavior of cordierite and zircon based samples using image and morphological analyses. in Materials Letters. 2018;220:136-139.
doi:10.1016/j.matlet.2018.03.029 .

Martinović, Sanja, Vlahović, Milica, Dojčinović, Marina, Pavlović, Marko, Volkov-Husović, Tatjana, "Comparison of cavitation erosion behavior of cordierite and zircon based samples using image and morphological analyses" in Materials Letters, 220 (2018):136-139,
https://doi.org/10.1016/j.matlet.2018.03.029 . .

TY  - JOUR
AU  - Milenkovic, Ivana
AU  - Radotić, Ksenija
AU  - Matović, Branko
AU  - Prekajski, Marija
AU  - Živković, Ljiljana S.
AU  - Jakovljević, Dragica
AU  - Gojgić-Cvijović, Gordana
AU  - Beškoski, Vladimir
PY  - 2018
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/2447
AB  - Cerium oxide (CeO2) nanoparticles (CONPs) are interesting biomaterials with various applications in biomedicine, cosmetics and the pharmaceutical industry, but with limited practical application because of their low stability in aqueous media. The aim of this study was to obtain CONPs with increased stability by coating the particles. Microbial exopolysaccharides (levan, pullulan) and glucose were used to prepare CONPs under different synthesis conditions. Coating was attempted by adding the carbohydrates during (direct coating) or after (subsequent coating) the synthesis of CONPs. The obtained nanoparticles were characterized by X-Ray diffraction analysis, Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The suspension stability of the uncoated and coated CONPs in aqueous media was evaluated by measuring the hydrodynamic size, zeta potential and turbidity. The FT-IR spectra revealed the differences between coated CONPs and showed the success of subsequent coating with carbohydrates. Coating with carbohydrates improved the stability the CONP suspension by decreasing the size of aggregated particles. The suspensions of levan- and glucose-coated CONPs had the best stability. In this study, CONPs were prepared using non-toxic materials, which were completely environmentally friendly. The obtained results open new horizons for CONP synthesis, improving their biological applications.
PB  - Serbian Chemical Soc, Belgrade
T2  - Journal of the Serbian Chemical Society
T1  - Improving stability of cerium oxide nanoparticles by microbial polysaccharides coating
VL  - 83
IS  - 6
SP  - 745
EP  - 757
DO  - 10.2298/JSC171205031M
ER  - 

@article{
author = "Milenkovic, Ivana and Radotić, Ksenija and Matović, Branko and Prekajski, Marija and Živković, Ljiljana S. and Jakovljević, Dragica and Gojgić-Cvijović, Gordana and Beškoski, Vladimir",
year = "2018",
abstract = "Cerium oxide (CeO2) nanoparticles (CONPs) are interesting biomaterials with various applications in biomedicine, cosmetics and the pharmaceutical industry, but with limited practical application because of their low stability in aqueous media. The aim of this study was to obtain CONPs with increased stability by coating the particles. Microbial exopolysaccharides (levan, pullulan) and glucose were used to prepare CONPs under different synthesis conditions. Coating was attempted by adding the carbohydrates during (direct coating) or after (subsequent coating) the synthesis of CONPs. The obtained nanoparticles were characterized by X-Ray diffraction analysis, Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The suspension stability of the uncoated and coated CONPs in aqueous media was evaluated by measuring the hydrodynamic size, zeta potential and turbidity. The FT-IR spectra revealed the differences between coated CONPs and showed the success of subsequent coating with carbohydrates. Coating with carbohydrates improved the stability the CONP suspension by decreasing the size of aggregated particles. The suspensions of levan- and glucose-coated CONPs had the best stability. In this study, CONPs were prepared using non-toxic materials, which were completely environmentally friendly. The obtained results open new horizons for CONP synthesis, improving their biological applications.",
publisher = "Serbian Chemical Soc, Belgrade",
journal = "Journal of the Serbian Chemical Society",
title = "Improving stability of cerium oxide nanoparticles by microbial polysaccharides coating",
volume = "83",
number = "6",
pages = "745-757",
doi = "10.2298/JSC171205031M"
}

Milenkovic, I., Radotić, K., Matović, B., Prekajski, M., Živković, L. S., Jakovljević, D., Gojgić-Cvijović, G.,& Beškoski, V.. (2018). Improving stability of cerium oxide nanoparticles by microbial polysaccharides coating. in Journal of the Serbian Chemical Society
Serbian Chemical Soc, Belgrade., 83(6), 745-757.
https://doi.org/10.2298/JSC171205031M

Milenkovic I, Radotić K, Matović B, Prekajski M, Živković LS, Jakovljević D, Gojgić-Cvijović G, Beškoski V. Improving stability of cerium oxide nanoparticles by microbial polysaccharides coating. in Journal of the Serbian Chemical Society. 2018;83(6):745-757.
doi:10.2298/JSC171205031M .

Milenkovic, Ivana, Radotić, Ksenija, Matović, Branko, Prekajski, Marija, Živković, Ljiljana S., Jakovljević, Dragica, Gojgić-Cvijović, Gordana, Beškoski, Vladimir, "Improving stability of cerium oxide nanoparticles by microbial polysaccharides coating" in Journal of the Serbian Chemical Society, 83, no. 6 (2018):745-757,
https://doi.org/10.2298/JSC171205031M . .

TY  - JOUR
AU  - Srećković, Milesa Ž.
AU  - Pantelić, Slađana N.
AU  - Stanković, Srboljub J.
AU  - Polić, Suzana R.
AU  - Ivanović, Nenad B.
AU  - Bugarinović, Aleksandar R.
AU  - Ostojić, Stanko M.
PY  - 2017
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/6047
AB  - The paper presents a brief overview of contemporary ELION techniques with stress on their use for material modification and dozimetry. In the attempt to avoid some common misjudges of irradiation effects, special attention is paid to exact definition of irradiation geometry and careful adjustment of dose rates, which en able a proper elaboration of experimental results. In particular, effects of γ -rays irradiation on properties of commercial optical fibres, splitters, connectors, and fibre joints are examined, which enables monitoring of irradiation effects in complex configurations made of materials with different radiation hardness (resistance). It has been established that γ -rays irradiation of the investigated elements influences, in different ways, the transmission of laser beam signals of various wavelengths, under different modulation regimes. After irradiation, the signal attenuation is noticeably larger, both in optical connectors and optical splitter, than be fore it, and the effect in creases in time. The effects are more pronounced at the 99 % than at the 1 % Y-splitter out put at both measured wave lengths, and are more pronounced at 1310 nm than at 1550 nm.
AB  - Rad predstavlja kratak osvrt na elionske tehnike sa akcentom na njihovoj upotrebi za modifikaciju materijala i dozimetriju. U pokušaju da se izbegnu neka uobičajena, pogrešna mišljenja o efektima zračenja, posebna pažnja je posvećena tačnoj definiciji geometrije zračenja i pažljivom prilagođavanju jačine doze, koji omogućavaju pravilnu obradu eksperimentalnih rezultata. Posebno su ispitivani efekti ozračivanja gama zracima komercijalnih optičkih vlakana, optičkih račvi, konektora i spojeva fibera, što omogućuje praćenje efekta ozračivanja na kompleksne konfiguracije uređaja od materijala sa različitom radijacionom otpornošću. Nađeno je da ozračivanje ispitivanih elemenata gama zracima na razne načine utiče na transmisiju signala – laserskih snopova različitih talasnih dužina i pod raznim efektima modulacije. Posle ozračivanja, slabljenje signala je znatno veće i kod optičkih konektora i kod optičke račve, nego pre njega, a efekat raste sa vremenom. Efekti su mnogo izraženiji kod 99 %, nego kod 1 % izlaza Y račve na obe merene talasne dužine, i više su izraženi na 1310 nm, nego na 1550 nm.
PB  - Vinča Institute of Nuclear Sciences
T2  - Nuclear Technology & Radiation Protection
T1  - Gamma irradiation effects in optical fibres, splitters, and connectors
T1  - Efekti gama zračenja na optička vlakna, račve i konektore
VL  - 32
IS  - 4
SP  - 375
EP  - 380
DO  - 10.2298/NTRP1704375S
ER  - 

@article{
author = "Srećković, Milesa Ž. and Pantelić, Slađana N. and Stanković, Srboljub J. and Polić, Suzana R. and Ivanović, Nenad B. and Bugarinović, Aleksandar R. and Ostojić, Stanko M.",
year = "2017",
abstract = "The paper presents a brief overview of contemporary ELION techniques with stress on their use for material modification and dozimetry. In the attempt to avoid some common misjudges of irradiation effects, special attention is paid to exact definition of irradiation geometry and careful adjustment of dose rates, which en able a proper elaboration of experimental results. In particular, effects of γ -rays irradiation on properties of commercial optical fibres, splitters, connectors, and fibre joints are examined, which enables monitoring of irradiation effects in complex configurations made of materials with different radiation hardness (resistance). It has been established that γ -rays irradiation of the investigated elements influences, in different ways, the transmission of laser beam signals of various wavelengths, under different modulation regimes. After irradiation, the signal attenuation is noticeably larger, both in optical connectors and optical splitter, than be fore it, and the effect in creases in time. The effects are more pronounced at the 99 % than at the 1 % Y-splitter out put at both measured wave lengths, and are more pronounced at 1310 nm than at 1550 nm., Rad predstavlja kratak osvrt na elionske tehnike sa akcentom na njihovoj upotrebi za modifikaciju materijala i dozimetriju. U pokušaju da se izbegnu neka uobičajena, pogrešna mišljenja o efektima zračenja, posebna pažnja je posvećena tačnoj definiciji geometrije zračenja i pažljivom prilagođavanju jačine doze, koji omogućavaju pravilnu obradu eksperimentalnih rezultata. Posebno su ispitivani efekti ozračivanja gama zracima komercijalnih optičkih vlakana, optičkih račvi, konektora i spojeva fibera, što omogućuje praćenje efekta ozračivanja na kompleksne konfiguracije uređaja od materijala sa različitom radijacionom otpornošću. Nađeno je da ozračivanje ispitivanih elemenata gama zracima na razne načine utiče na transmisiju signala – laserskih snopova različitih talasnih dužina i pod raznim efektima modulacije. Posle ozračivanja, slabljenje signala je znatno veće i kod optičkih konektora i kod optičke račve, nego pre njega, a efekat raste sa vremenom. Efekti su mnogo izraženiji kod 99 %, nego kod 1 % izlaza Y račve na obe merene talasne dužine, i više su izraženi na 1310 nm, nego na 1550 nm.",
publisher = "Vinča Institute of Nuclear Sciences",
journal = "Nuclear Technology & Radiation Protection",
title = "Gamma irradiation effects in optical fibres, splitters, and connectors, Efekti gama zračenja na optička vlakna, račve i konektore",
volume = "32",
number = "4",
pages = "375-380",
doi = "10.2298/NTRP1704375S"
}

Srećković, M. Ž., Pantelić, S. N., Stanković, S. J., Polić, S. R., Ivanović, N. B., Bugarinović, A. R.,& Ostojić, S. M.. (2017). Gamma irradiation effects in optical fibres, splitters, and connectors. in Nuclear Technology & Radiation Protection
Vinča Institute of Nuclear Sciences., 32(4), 375-380.
https://doi.org/10.2298/NTRP1704375S

Srećković MŽ, Pantelić SN, Stanković SJ, Polić SR, Ivanović NB, Bugarinović AR, Ostojić SM. Gamma irradiation effects in optical fibres, splitters, and connectors. in Nuclear Technology & Radiation Protection. 2017;32(4):375-380.
doi:10.2298/NTRP1704375S .

Srećković, Milesa Ž., Pantelić, Slađana N., Stanković, Srboljub J., Polić, Suzana R., Ivanović, Nenad B., Bugarinović, Aleksandar R., Ostojić, Stanko M., "Gamma irradiation effects in optical fibres, splitters, and connectors" in Nuclear Technology & Radiation Protection, 32, no. 4 (2017):375-380,
https://doi.org/10.2298/NTRP1704375S . .

TY  - CONF
AU  - Pavlović, Marko
AU  - Martinović, Sanja
AU  - Dojčinović, Marina
AU  - Vlahović, Milica
AU  - Stević, Zoran
AU  - Volkov Husović, Tatjana
PY  - 2017
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/7259
AB  - This study is focused on monitoring the degradation level of zircon based ceramic materials during exposure to cavitation. In addition to conventional degradation monitoring methods, weight loss measuring, the emphasis is on monitoring the changes occurring at the surface of the sample by taking the photos and analyzing of these images. In this paper, several parameters are monitored by image analysis: the level of surface degradation, the number of pits, and the average area of the pits. This method proved to be very fast and useful for a quantification of damage which could improve the prediction of the material lifetime.
PB  - Bor : University of Belgrade - Technical Faculty in Bor
C3  - Proceedings - 49th International October Conference on Mining and Metallurgy-IOC-2017, October 18-21 2017, Bor Lake, Serbia
T1  - Damage level evaluation of zircon samples caused by cavitation erosion using image analysis
SP  - 594
EP  - 597
UR  - https://hdl.handle.net/21.15107/rcub_cer_7259
ER  - 

@conference{
author = "Pavlović, Marko and Martinović, Sanja and Dojčinović, Marina and Vlahović, Milica and Stević, Zoran and Volkov Husović, Tatjana",
year = "2017",
abstract = "This study is focused on monitoring the degradation level of zircon based ceramic materials during exposure to cavitation. In addition to conventional degradation monitoring methods, weight loss measuring, the emphasis is on monitoring the changes occurring at the surface of the sample by taking the photos and analyzing of these images. In this paper, several parameters are monitored by image analysis: the level of surface degradation, the number of pits, and the average area of the pits. This method proved to be very fast and useful for a quantification of damage which could improve the prediction of the material lifetime.",
publisher = "Bor : University of Belgrade - Technical Faculty in Bor",
journal = "Proceedings - 49th International October Conference on Mining and Metallurgy-IOC-2017, October 18-21 2017, Bor Lake, Serbia",
title = "Damage level evaluation of zircon samples caused by cavitation erosion using image analysis",
pages = "594-597",
url = "https://hdl.handle.net/21.15107/rcub_cer_7259"
}

Pavlović, M., Martinović, S., Dojčinović, M., Vlahović, M., Stević, Z.,& Volkov Husović, T.. (2017). Damage level evaluation of zircon samples caused by cavitation erosion using image analysis. in Proceedings - 49th International October Conference on Mining and Metallurgy-IOC-2017, October 18-21 2017, Bor Lake, Serbia
Bor : University of Belgrade - Technical Faculty in Bor., 594-597.
https://hdl.handle.net/21.15107/rcub_cer_7259

Pavlović M, Martinović S, Dojčinović M, Vlahović M, Stević Z, Volkov Husović T. Damage level evaluation of zircon samples caused by cavitation erosion using image analysis. in Proceedings - 49th International October Conference on Mining and Metallurgy-IOC-2017, October 18-21 2017, Bor Lake, Serbia. 2017;:594-597.
https://hdl.handle.net/21.15107/rcub_cer_7259 .

Pavlović, Marko, Martinović, Sanja, Dojčinović, Marina, Vlahović, Milica, Stević, Zoran, Volkov Husović, Tatjana, "Damage level evaluation of zircon samples caused by cavitation erosion using image analysis" in Proceedings - 49th International October Conference on Mining and Metallurgy-IOC-2017, October 18-21 2017, Bor Lake, Serbia (2017):594-597,
https://hdl.handle.net/21.15107/rcub_cer_7259 .

TY  - CONF
AU  - Pavlović, Marko
AU  - Martinović, Sanja
AU  - Vlahović, Milica
AU  - Dojčinović, Marina
AU  - Stević, Zoran
AU  - Volkov Husović, Tatjana
AU  - Bondarenko, Olexander
PY  - 2017
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/6917
AB  - Cavitation erosion of mullite samples was monitored using vibratory cavitation set up with stationary sample. The level of degradation of the sample was monitored using weight loss and image analysis. Thermal imaging analysis was focused on determination of temperature line profile and histogram of temperature distribution at the end of the experiment. The results of image analysis were compared with infrared thermography results.
PB  - ПП Полiтexперiодика
C3  - Proceedings - XVIII International scientific-practical conference, Modern information and electronic technologies
T1  - Implementation of infrared thermography on defects monitoring during cavitation erosion of mullite ceramic
SP  - 48
EP  - 51
UR  - https://hdl.handle.net/21.15107/rcub_cer_6917
ER  - 

@conference{
author = "Pavlović, Marko and Martinović, Sanja and Vlahović, Milica and Dojčinović, Marina and Stević, Zoran and Volkov Husović, Tatjana and Bondarenko, Olexander",
year = "2017",
abstract = "Cavitation erosion of mullite samples was monitored using vibratory cavitation set up with stationary sample. The level of degradation of the sample was monitored using weight loss and image analysis. Thermal imaging analysis was focused on determination of temperature line profile and histogram of temperature distribution at the end of the experiment. The results of image analysis were compared with infrared thermography results.",
publisher = "ПП Полiтexперiодика",
journal = "Proceedings - XVIII International scientific-practical conference, Modern information and electronic technologies",
title = "Implementation of infrared thermography on defects monitoring during cavitation erosion of mullite ceramic",
pages = "48-51",
url = "https://hdl.handle.net/21.15107/rcub_cer_6917"
}

Pavlović, M., Martinović, S., Vlahović, M., Dojčinović, M., Stević, Z., Volkov Husović, T.,& Bondarenko, O.. (2017). Implementation of infrared thermography on defects monitoring during cavitation erosion of mullite ceramic. in Proceedings - XVIII International scientific-practical conference, Modern information and electronic technologies
ПП Полiтexперiодика., 48-51.
https://hdl.handle.net/21.15107/rcub_cer_6917

Pavlović M, Martinović S, Vlahović M, Dojčinović M, Stević Z, Volkov Husović T, Bondarenko O. Implementation of infrared thermography on defects monitoring during cavitation erosion of mullite ceramic. in Proceedings - XVIII International scientific-practical conference, Modern information and electronic technologies. 2017;:48-51.
https://hdl.handle.net/21.15107/rcub_cer_6917 .

Pavlović, Marko, Martinović, Sanja, Vlahović, Milica, Dojčinović, Marina, Stević, Zoran, Volkov Husović, Tatjana, Bondarenko, Olexander, "Implementation of infrared thermography on defects monitoring during cavitation erosion of mullite ceramic" in Proceedings - XVIII International scientific-practical conference, Modern information and electronic technologies (2017):48-51,
https://hdl.handle.net/21.15107/rcub_cer_6917 .

TY  - JOUR
AU  - Pavlović, Marko D.
AU  - Dojčinović, Marina
AU  - Martinović, Sanja
AU  - Vlahović, Milica
AU  - Stević, Zoran
AU  - Jovanović, Marina N.
AU  - Volkov-Husović, Tatjana
PY  - 2017
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/2056
AB  - Mechanical shock of zircon based ceramic induced by cavitation erosion testing was investigated in this study. Several parameters were followed in order to determine level of material degradation during the cavitation erosion testing. Mass loss was taken as a conventional criterion for material degradation, while the level of surface degradation was evaluated by image and thermal imaging analyses. Results show high cavitation resistance of zircon ceramics and their suitability when vigorous cavitation erosion environment is expected.
PB  - Belgrade : International Institute for the Science of Sintering
T2  - Science of Sintering
T1  - Determination of Degradation Level during Cavitation Erosion of Zircon Based Ceramic
VL  - 49
IS  - 2
SP  - 175
EP  - 185
DO  - 10.2298/SOS1702175P
ER  - 

@article{
author = "Pavlović, Marko D. and Dojčinović, Marina and Martinović, Sanja and Vlahović, Milica and Stević, Zoran and Jovanović, Marina N. and Volkov-Husović, Tatjana",
year = "2017",
abstract = "Mechanical shock of zircon based ceramic induced by cavitation erosion testing was investigated in this study. Several parameters were followed in order to determine level of material degradation during the cavitation erosion testing. Mass loss was taken as a conventional criterion for material degradation, while the level of surface degradation was evaluated by image and thermal imaging analyses. Results show high cavitation resistance of zircon ceramics and their suitability when vigorous cavitation erosion environment is expected.",
publisher = "Belgrade : International Institute for the Science of Sintering",
journal = "Science of Sintering",
title = "Determination of Degradation Level during Cavitation Erosion of Zircon Based Ceramic",
volume = "49",
number = "2",
pages = "175-185",
doi = "10.2298/SOS1702175P"
}

Pavlović, M. D., Dojčinović, M., Martinović, S., Vlahović, M., Stević, Z., Jovanović, M. N.,& Volkov-Husović, T.. (2017). Determination of Degradation Level during Cavitation Erosion of Zircon Based Ceramic. in Science of Sintering
Belgrade : International Institute for the Science of Sintering., 49(2), 175-185.
https://doi.org/10.2298/SOS1702175P

Pavlović MD, Dojčinović M, Martinović S, Vlahović M, Stević Z, Jovanović MN, Volkov-Husović T. Determination of Degradation Level during Cavitation Erosion of Zircon Based Ceramic. in Science of Sintering. 2017;49(2):175-185.
doi:10.2298/SOS1702175P .

Pavlović, Marko D., Dojčinović, Marina, Martinović, Sanja, Vlahović, Milica, Stević, Zoran, Jovanović, Marina N., Volkov-Husović, Tatjana, "Determination of Degradation Level during Cavitation Erosion of Zircon Based Ceramic" in Science of Sintering, 49, no. 2 (2017):175-185,
https://doi.org/10.2298/SOS1702175P . .