TY  - JOUR
AU  - Manasijević, Dragan
AU  - Balanović, Ljubiša
AU  - Marković, Ivana
AU  - Gorgievski, Milan
AU  - Stamenković, Uroš
AU  - Minić, Duško
AU  - Premović, Milena
AU  - Đorđević, Aleksandar
AU  - Ćosović, Vladan
PY  - 2022
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/4808
AB  - Microstructure, phase transitions and thermal properties including thermal diffusivity and thermal conductivity of four Ag–Ge alloys with 20, 40, 60 and 80 at % of Ge were experimentally investigated in this study. Observation and analysis of the alloy microstructures and morphologies of (Ge) phase in the hypereutectic alloys were carried out using optical microscopy and scanning electron microscopy with energy-dispersive X-ray spectrometry (SEM–EDS). Phase transitions of the alloys were studied using differential scanning calorimetry (DSC). Experimentally determined temperature of the eutectic reaction was 650.9 °C. The xenon flash method was used for thermal diffusivity measurements in the temperature range from 25 to 400 °C. Based on the measured values of thermal diffusivity, thermal conductivity of the solid Ag–Ge alloys was determined. It was found that both thermal diffusivity and thermal conductivity show a minimum at 20 at % Ge which is close to the eutectic composition. The obtained results were compared with the results of thermodynamic calculation and literature data, and a close agreement was observed.
PB  - Springer
T2  - Journal of Thermal Analysis and Calorimetry
T1  - Study of thermal properties and microstructure of the Ag–Ge alloys
VL  - 147
SP  - 1955
EP  - 1964
DO  - 10.1007/s10973-021-10664-y
ER  - 

@article{
author = "Manasijević, Dragan and Balanović, Ljubiša and Marković, Ivana and Gorgievski, Milan and Stamenković, Uroš and Minić, Duško and Premović, Milena and Đorđević, Aleksandar and Ćosović, Vladan",
year = "2022",
abstract = "Microstructure, phase transitions and thermal properties including thermal diffusivity and thermal conductivity of four Ag–Ge alloys with 20, 40, 60 and 80 at % of Ge were experimentally investigated in this study. Observation and analysis of the alloy microstructures and morphologies of (Ge) phase in the hypereutectic alloys were carried out using optical microscopy and scanning electron microscopy with energy-dispersive X-ray spectrometry (SEM–EDS). Phase transitions of the alloys were studied using differential scanning calorimetry (DSC). Experimentally determined temperature of the eutectic reaction was 650.9 °C. The xenon flash method was used for thermal diffusivity measurements in the temperature range from 25 to 400 °C. Based on the measured values of thermal diffusivity, thermal conductivity of the solid Ag–Ge alloys was determined. It was found that both thermal diffusivity and thermal conductivity show a minimum at 20 at % Ge which is close to the eutectic composition. The obtained results were compared with the results of thermodynamic calculation and literature data, and a close agreement was observed.",
publisher = "Springer",
journal = "Journal of Thermal Analysis and Calorimetry",
title = "Study of thermal properties and microstructure of the Ag–Ge alloys",
volume = "147",
pages = "1955-1964",
doi = "10.1007/s10973-021-10664-y"
}

Manasijević, D., Balanović, L., Marković, I., Gorgievski, M., Stamenković, U., Minić, D., Premović, M., Đorđević, A.,& Ćosović, V.. (2022). Study of thermal properties and microstructure of the Ag–Ge alloys. in Journal of Thermal Analysis and Calorimetry
Springer., 147, 1955-1964.
https://doi.org/10.1007/s10973-021-10664-y

Manasijević D, Balanović L, Marković I, Gorgievski M, Stamenković U, Minić D, Premović M, Đorđević A, Ćosović V. Study of thermal properties and microstructure of the Ag–Ge alloys. in Journal of Thermal Analysis and Calorimetry. 2022;147:1955-1964.
doi:10.1007/s10973-021-10664-y .

Manasijević, Dragan, Balanović, Ljubiša, Marković, Ivana, Gorgievski, Milan, Stamenković, Uroš, Minić, Duško, Premović, Milena, Đorđević, Aleksandar, Ćosović, Vladan, "Study of thermal properties and microstructure of the Ag–Ge alloys" in Journal of Thermal Analysis and Calorimetry, 147 (2022):1955-1964,
https://doi.org/10.1007/s10973-021-10664-y . .

TY  - JOUR
AU  - Manasijević, Dragan
AU  - Balanović, Ljubiša
AU  - Marković, Ivana
AU  - Ćosović, Vladan
AU  - Gorgievski, Milan
AU  - Stamenković, Uroš
AU  - Božinović, Kristina
PY  - 2022
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/5368
AB  - Thermal transport properties of solid Bi-Cu alloys have been investigated over a wide composition range and temperature range ranging from 25 to 250 °C. The flash method was used to determine thermal diffusivity. Thermal diffusivity was discovered to decrease continuously with increasing temperature and bismuth content. The indirect Archimedean method was used to determine the density of the Bi-Cu alloys at 25 °C. The obtained results show that the density of the studied alloys decreases slightly as the copper content increases. Thermal conductivity of the alloys was calculated using measured diffusivity, density, and a calculated specific heat capacity. The thermal conductivity of the studied Bi-Cu alloys decreases with increasing temperature and bismuth content, similar to thermal diffusivity. SEM with energy dispersive X-ray spectrometry (EDS) and differential scanning calorimetry (DSC) were used to examine the microstructure and melting behavior of Bi-Cu alloys, respectively. The eutectic temperature was measured to be 269.9±0.1 °C, and the measured phase transition temperatures and heat effects were compared to thermodynamic calculations using the CALPHAD method.
PB  - Belgrade : Association of Metallurgical Engineers of Serbia  ( AMES )
T2  - Metallurgical and Materials Engineering
T1  - Thermal transport properties and microstructure of the solid Bi-Cu alloys
VL  - 28
IS  - 3
SP  - 503
EP  - 514
DO  - 10.30544/841
ER  - 

@article{
author = "Manasijević, Dragan and Balanović, Ljubiša and Marković, Ivana and Ćosović, Vladan and Gorgievski, Milan and Stamenković, Uroš and Božinović, Kristina",
year = "2022",
abstract = "Thermal transport properties of solid Bi-Cu alloys have been investigated over a wide composition range and temperature range ranging from 25 to 250 °C. The flash method was used to determine thermal diffusivity. Thermal diffusivity was discovered to decrease continuously with increasing temperature and bismuth content. The indirect Archimedean method was used to determine the density of the Bi-Cu alloys at 25 °C. The obtained results show that the density of the studied alloys decreases slightly as the copper content increases. Thermal conductivity of the alloys was calculated using measured diffusivity, density, and a calculated specific heat capacity. The thermal conductivity of the studied Bi-Cu alloys decreases with increasing temperature and bismuth content, similar to thermal diffusivity. SEM with energy dispersive X-ray spectrometry (EDS) and differential scanning calorimetry (DSC) were used to examine the microstructure and melting behavior of Bi-Cu alloys, respectively. The eutectic temperature was measured to be 269.9±0.1 °C, and the measured phase transition temperatures and heat effects were compared to thermodynamic calculations using the CALPHAD method.",
publisher = "Belgrade : Association of Metallurgical Engineers of Serbia  ( AMES )",
journal = "Metallurgical and Materials Engineering",
title = "Thermal transport properties and microstructure of the solid Bi-Cu alloys",
volume = "28",
number = "3",
pages = "503-514",
doi = "10.30544/841"
}

Manasijević, D., Balanović, L., Marković, I., Ćosović, V., Gorgievski, M., Stamenković, U.,& Božinović, K.. (2022). Thermal transport properties and microstructure of the solid Bi-Cu alloys. in Metallurgical and Materials Engineering
Belgrade : Association of Metallurgical Engineers of Serbia  ( AMES )., 28(3), 503-514.
https://doi.org/10.30544/841

Manasijević D, Balanović L, Marković I, Ćosović V, Gorgievski M, Stamenković U, Božinović K. Thermal transport properties and microstructure of the solid Bi-Cu alloys. in Metallurgical and Materials Engineering. 2022;28(3):503-514.
doi:10.30544/841 .

Manasijević, Dragan, Balanović, Ljubiša, Marković, Ivana, Ćosović, Vladan, Gorgievski, Milan, Stamenković, Uroš, Božinović, Kristina, "Thermal transport properties and microstructure of the solid Bi-Cu alloys" in Metallurgical and Materials Engineering, 28, no. 3 (2022):503-514,
https://doi.org/10.30544/841 . .

TY  - JOUR
AU  - Manasijević, Dragan
AU  - Balanović, Ljubiša
AU  - Holjevac Grgurić, Tamara
AU  - Gorgievski, Milan
AU  - Marković, Ivana
AU  - Ćosović, Vladan
AU  - Premović, Milena
AU  - Minić, Duško
PY  - 2020
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3781
AB  - Low-melting alloys, based on bismuth and indium, have found commercial use in soldering, safety devices, coatings, and bonding applications. In this respect, the accurate knowledge  of  their  thermal  properties  such  as  melting  and  solidification  temperatures, latent heat of melting, supercooling tendency, etc. is of large importance. In the present research,   low-melting   alloy   with   nominal   composition   Bi40In40Pb20(at.   %)   was investigated by means of scanning electron microscopy(SEM) with energy dispersive X-ray spectrometry (EDS) and by differential scanning calorimetry (DSC). Microstructural and chemical (SEM-EDS) analysis has revealed the existence of two coexisting phases in the  prepared  alloy,  which  was  identified  as  BiInand  (Pb).  Melting  and  solidification temperatures  and  the  related  heat  effects  were  measured  by  the  DSC  technique.  The solidus temperature obtained from the DSC heating curves was 76.3 °C and the solidus temperature  obtained  from  the  corresponding  DSC  cooling  runs  was  61.2  °C.  The experimentally  obtained  results  were  compared  with  the  results  of  thermodynamic calculation according to CALPHAD (calculation of phase diagram) approach, and a close agreement was noticed.
PB  - Association of Metallurgical Engineers of Serbia (AMES)
T2  - Metallurgical and Materials Engineering
T1  - Thermal and microstructural analysis of the low-melting Bi-In-Pb alloy
VL  - 26
IS  - 4
SP  - 385
EP  - 394
DO  - 10.30544/564
ER  - 

@article{
author = "Manasijević, Dragan and Balanović, Ljubiša and Holjevac Grgurić, Tamara and Gorgievski, Milan and Marković, Ivana and Ćosović, Vladan and Premović, Milena and Minić, Duško",
year = "2020",
abstract = "Low-melting alloys, based on bismuth and indium, have found commercial use in soldering, safety devices, coatings, and bonding applications. In this respect, the accurate knowledge  of  their  thermal  properties  such  as  melting  and  solidification  temperatures, latent heat of melting, supercooling tendency, etc. is of large importance. In the present research,   low-melting   alloy   with   nominal   composition   Bi40In40Pb20(at.   %)   was investigated by means of scanning electron microscopy(SEM) with energy dispersive X-ray spectrometry (EDS) and by differential scanning calorimetry (DSC). Microstructural and chemical (SEM-EDS) analysis has revealed the existence of two coexisting phases in the  prepared  alloy,  which  was  identified  as  BiInand  (Pb).  Melting  and  solidification temperatures  and  the  related  heat  effects  were  measured  by  the  DSC  technique.  The solidus temperature obtained from the DSC heating curves was 76.3 °C and the solidus temperature  obtained  from  the  corresponding  DSC  cooling  runs  was  61.2  °C.  The experimentally  obtained  results  were  compared  with  the  results  of  thermodynamic calculation according to CALPHAD (calculation of phase diagram) approach, and a close agreement was noticed.",
publisher = "Association of Metallurgical Engineers of Serbia (AMES)",
journal = "Metallurgical and Materials Engineering",
title = "Thermal and microstructural analysis of the low-melting Bi-In-Pb alloy",
volume = "26",
number = "4",
pages = "385-394",
doi = "10.30544/564"
}

Manasijević, D., Balanović, L., Holjevac Grgurić, T., Gorgievski, M., Marković, I., Ćosović, V., Premović, M.,& Minić, D.. (2020). Thermal and microstructural analysis of the low-melting Bi-In-Pb alloy. in Metallurgical and Materials Engineering
Association of Metallurgical Engineers of Serbia (AMES)., 26(4), 385-394.
https://doi.org/10.30544/564

Manasijević D, Balanović L, Holjevac Grgurić T, Gorgievski M, Marković I, Ćosović V, Premović M, Minić D. Thermal and microstructural analysis of the low-melting Bi-In-Pb alloy. in Metallurgical and Materials Engineering. 2020;26(4):385-394.
doi:10.30544/564 .

Manasijević, Dragan, Balanović, Ljubiša, Holjevac Grgurić, Tamara, Gorgievski, Milan, Marković, Ivana, Ćosović, Vladan, Premović, Milena, Minić, Duško, "Thermal and microstructural analysis of the low-melting Bi-In-Pb alloy" in Metallurgical and Materials Engineering, 26, no. 4 (2020):385-394,
https://doi.org/10.30544/564 . .

TY  - JOUR
AU  - Manasijević, Dragan
AU  - Balanović, Ljubiša
AU  - Holjevac Grgurić, Tamara
AU  - Gorgievski, Milan
AU  - Marković, Ivana
AU  - Ćosović, Vladan
AU  - Premović, Milena
AU  - Minić, Duško
PY  - 2020
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/4222
AB  - Low-melting alloys, based on bismuth and indium, have found commercial use in soldering, safety devices, coatings, and bonding applications. In this respect, the accurate knowledge of their thermal properties such as melting and solidification temperatures, latent heat of melting, supercooling tendency, etc. is of large importance. In the present research, low-melting alloy with nominal composition Bi40In40Pb20 (at. %) was investigated by means of scanning electron microscopy (SEM) with energy dispersive Xray spectrometry (EDS) and by differential scanning calorimetry (DSC). Microstructural and chemical (SEM-EDS) analysis has revealed the existence of two coexisting phases in the prepared alloy, which was identified as BiIn and (Pb). Melting and solidification temperatures and the related heat effects were measured by the DSC technique. The solidus temperature obtained from the DSC heating curves was 76.3 °C and the solidus temperature obtained from the corresponding DSC cooling runs was 61.2 °C. The experimentally obtained results were compared with the results of thermodynamic calculation according to CALPHAD (calculation of phase diagram) approach, and a close agreement was noticed.
PB  - Serbia : Association of Metallurgical Engineers of Serbia
T2  - Metallurgical & Materials Engineering
T1  - Thermal and microstructural analysis of the low-melting Bi-In-Pb alloy
VL  - 26
IS  - 4
SP  - 385
EP  - 394
DO  - 10.30544/564
ER  - 

@article{
author = "Manasijević, Dragan and Balanović, Ljubiša and Holjevac Grgurić, Tamara and Gorgievski, Milan and Marković, Ivana and Ćosović, Vladan and Premović, Milena and Minić, Duško",
year = "2020",
abstract = "Low-melting alloys, based on bismuth and indium, have found commercial use in soldering, safety devices, coatings, and bonding applications. In this respect, the accurate knowledge of their thermal properties such as melting and solidification temperatures, latent heat of melting, supercooling tendency, etc. is of large importance. In the present research, low-melting alloy with nominal composition Bi40In40Pb20 (at. %) was investigated by means of scanning electron microscopy (SEM) with energy dispersive Xray spectrometry (EDS) and by differential scanning calorimetry (DSC). Microstructural and chemical (SEM-EDS) analysis has revealed the existence of two coexisting phases in the prepared alloy, which was identified as BiIn and (Pb). Melting and solidification temperatures and the related heat effects were measured by the DSC technique. The solidus temperature obtained from the DSC heating curves was 76.3 °C and the solidus temperature obtained from the corresponding DSC cooling runs was 61.2 °C. The experimentally obtained results were compared with the results of thermodynamic calculation according to CALPHAD (calculation of phase diagram) approach, and a close agreement was noticed.",
publisher = "Serbia : Association of Metallurgical Engineers of Serbia",
journal = "Metallurgical & Materials Engineering",
title = "Thermal and microstructural analysis of the low-melting Bi-In-Pb alloy",
volume = "26",
number = "4",
pages = "385-394",
doi = "10.30544/564"
}

Manasijević, D., Balanović, L., Holjevac Grgurić, T., Gorgievski, M., Marković, I., Ćosović, V., Premović, M.,& Minić, D.. (2020). Thermal and microstructural analysis of the low-melting Bi-In-Pb alloy. in Metallurgical & Materials Engineering
Serbia : Association of Metallurgical Engineers of Serbia., 26(4), 385-394.
https://doi.org/10.30544/564

Manasijević D, Balanović L, Holjevac Grgurić T, Gorgievski M, Marković I, Ćosović V, Premović M, Minić D. Thermal and microstructural analysis of the low-melting Bi-In-Pb alloy. in Metallurgical & Materials Engineering. 2020;26(4):385-394.
doi:10.30544/564 .

Manasijević, Dragan, Balanović, Ljubiša, Holjevac Grgurić, Tamara, Gorgievski, Milan, Marković, Ivana, Ćosović, Vladan, Premović, Milena, Minić, Duško, "Thermal and microstructural analysis of the low-melting Bi-In-Pb alloy" in Metallurgical & Materials Engineering, 26, no. 4 (2020):385-394,
https://doi.org/10.30544/564 . .

TY  - JOUR
AU  - Balanović, Ljubiša
AU  - Živković, Dragana
AU  - Manasijević, Dragan
AU  - Marković, Ivana
AU  - Talijan, Nadežda M.
AU  - Ćosović, Vladan
AU  - Marjanović, Bata
PY  - 2012
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/1078
AB  - The purpose of this study is to investigate structural and mechanical properties of some aluminum-based alloys. Microstructures of the Al-Sn and Al-Zn binary alloys were examined using optic microscopy. The mechanical properties - Vickers hardness and micro hardness tests were investigated according to standard procedure.
PB  - Institut za bakar Bor
T2  - Bakar
T1  - Structural and mechanical properties of some aluminum-based binary alloys
VL  - 37
IS  - 1
SP  - 79
EP  - 86
UR  - https://hdl.handle.net/21.15107/rcub_cer_1078
ER  - 

@article{
author = "Balanović, Ljubiša and Živković, Dragana and Manasijević, Dragan and Marković, Ivana and Talijan, Nadežda M. and Ćosović, Vladan and Marjanović, Bata",
year = "2012",
abstract = "The purpose of this study is to investigate structural and mechanical properties of some aluminum-based alloys. Microstructures of the Al-Sn and Al-Zn binary alloys were examined using optic microscopy. The mechanical properties - Vickers hardness and micro hardness tests were investigated according to standard procedure.",
publisher = "Institut za bakar Bor",
journal = "Bakar",
title = "Structural and mechanical properties of some aluminum-based binary alloys",
volume = "37",
number = "1",
pages = "79-86",
url = "https://hdl.handle.net/21.15107/rcub_cer_1078"
}

Balanović, L., Živković, D., Manasijević, D., Marković, I., Talijan, N. M., Ćosović, V.,& Marjanović, B.. (2012). Structural and mechanical properties of some aluminum-based binary alloys. in Bakar
Institut za bakar Bor., 37(1), 79-86.
https://hdl.handle.net/21.15107/rcub_cer_1078

Balanović L, Živković D, Manasijević D, Marković I, Talijan NM, Ćosović V, Marjanović B. Structural and mechanical properties of some aluminum-based binary alloys. in Bakar. 2012;37(1):79-86.
https://hdl.handle.net/21.15107/rcub_cer_1078 .

Balanović, Ljubiša, Živković, Dragana, Manasijević, Dragan, Marković, Ivana, Talijan, Nadežda M., Ćosović, Vladan, Marjanović, Bata, "Structural and mechanical properties of some aluminum-based binary alloys" in Bakar, 37, no. 1 (2012):79-86,
https://hdl.handle.net/21.15107/rcub_cer_1078 .