ЦЕР - Централни Репозиторијум ИХТМ-а
Институт за хемију, технологију и металургију
    • English
    • Српски
    • Српски (Serbia)
  • Српски (ћирилица) 
    • Енглески
    • Српски (ћирилица)
    • Српски (латиница)
  • Пријава
Преглед рада 
  •   ЦЕР - Централни репозиторијум ИХТМ-а
  • IHTM
  • Radovi istraživača / Researchers' publications
  • Преглед рада
  •   ЦЕР - Централни репозиторијум ИХТМ-а
  • IHTM
  • Radovi istraživača / Researchers' publications
  • Преглед рада
JavaScript is disabled for your browser. Some features of this site may not work without it.

Strukturne karakteristike galvanskih prevlaka bakra

Structural characteristics of electrodeposited copper coatings

Thumbnail
2009
osnovni rad (847.7Kb)
Аутори
Tomić, M.V.
Pavlović, M.G.
Pavlović, Ljubica J.
Nikolić, Nebojša D.
Чланак у часопису (Објављена верзија)
Метаподаци
Приказ свих података о документу
Апстракт
Uzorci bakra su podvrgnuti mehaničkom i elektrohemijskom glačanju u odgovarajućim elektrolitima za elektrohemijsko glačanje. Na tako prethodno pripremljene površine supstrata izvršeno je taloţenje prevlaka bakra iz dva kupatila i to iz osnovnog elektrolita (OR) sastava: 240 g/dm3 CuSO4 ∙ 5 H2O + 60 g/dm3 H2SO4 i kupatila sa dodacima za sjaj (OR +DS). Pomoću STM i AFM tehnika precizno su prikazane strukturne osobine koje odreĎuju da li je metalna površina ogledalski sjajna ili ne, odnosno da li dobijena topografija površine manje ili više hrapava. UtvrĎeno je znatno povećanje hrapavosti uzoraka na koje je taloţena prevlaka bakra iz osnovnog sulfatnog kupatila (OR) u odnosu na mehanički i mehanički i elektrohemijske pripremane uzorke. TakoĎe, pri taloţenju prevlaka iz kupatila sa dodacima za sjaj (OR +DS), došlo je do smanjenja hrapavosti površine.
The samples of rolled copper were mechanically and electrochemically polished in suitable electrolytes for electrochemical polishing. These substrate surfaces that had been prepared in advance, served as the basis for depositing of copper layers from two baths, namely, from the basic electrolyte(OR) with the following composition: 240 g/dm3 CuSO4 ∙ 5 H2O + 60 g/dm3 H2SO4i as well as from the bath which contained brightening addition agents(OR +DS). STM and AFM techniques show in great detail the structural properties which determine whether the metal surfaceis are as bright as a mirrior or not, that is, whether the obtained topography of the surface is more or less rough. It was determined that a considerable increase of roughness occurred in the samples where copper layers were deposited from the basic sulfate bath (OR) when compared with mechanical, and mechanical-electrochemical samples. In addition, depositing of the samples from the bath with brightening addition agents (OR +DS) r...esulted in the decrease of surface roughness.

Кључне речи:
bakar / elektrolit / prevlaka / Copper / Electrolyte / Coatings
Извор:
Journal of Engineering & Processing Management, 2009, 1, 2, 14-25
Издавач:
  • Bosnia and Herzegovina : University of East Sarajevo, Faculty of Technology

ISSN: 1840-4774; 2566-3615

[ Google Scholar ]
URI
https://jepm.tfzv.ues.rs.ba/index.php/Journal/article/view/132
https://cer.ihtm.bg.ac.rs/handle/123456789/3926
Колекције
  • Radovi istraživača / Researchers' publications
Институција
IHTM
TY  - JOUR
AU  - Tomić, M.V.
AU  - Pavlović, M.G.
AU  - Pavlović, Ljubica J.
AU  - Nikolić, Nebojša D.
PY  - 2009
UR  - https://jepm.tfzv.ues.rs.ba/index.php/Journal/article/view/132
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3926
AB  - Uzorci bakra su podvrgnuti mehaničkom i elektrohemijskom glačanju u odgovarajućim elektrolitima za elektrohemijsko glačanje. Na tako prethodno pripremljene površine supstrata izvršeno je taloţenje prevlaka bakra iz dva kupatila i to iz osnovnog elektrolita (OR) sastava: 240 g/dm3 CuSO4 ∙ 5 H2O + 60 g/dm3 H2SO4 i kupatila sa dodacima za sjaj (OR +DS). Pomoću STM i AFM tehnika precizno su prikazane strukturne osobine koje odreĎuju da li je metalna površina ogledalski sjajna ili ne, odnosno da li dobijena topografija površine manje ili više hrapava. UtvrĎeno je znatno povećanje hrapavosti uzoraka na koje je taloţena prevlaka bakra iz osnovnog sulfatnog kupatila (OR) u odnosu na mehanički i mehanički i elektrohemijske pripremane uzorke. TakoĎe, pri taloţenju prevlaka iz kupatila sa dodacima za sjaj (OR +DS), došlo je do smanjenja hrapavosti površine.
AB  - The samples of rolled copper were mechanically and electrochemically polished in suitable electrolytes for electrochemical polishing. These substrate surfaces that had been prepared in advance, served as the basis for depositing of copper layers from two baths, namely, from the basic electrolyte(OR) with the following composition: 240 g/dm3 CuSO4 ∙ 5 H2O + 60 g/dm3 H2SO4i as well as from the bath which contained brightening addition agents(OR +DS). STM and AFM techniques show in great detail the structural properties which determine whether the metal surfaceis are as bright as a mirrior or not, that is, whether the obtained topography of the surface is more or less rough. It was determined that a considerable increase of roughness occurred in the samples where copper layers were deposited from the basic sulfate bath (OR) when compared with mechanical, and mechanical-electrochemical samples. In addition, depositing of the samples from the bath with brightening addition agents (OR +DS) resulted in the decrease of surface roughness.
PB  - Bosnia and Herzegovina : University of East Sarajevo, Faculty of Technology
T2  - Journal of Engineering & Processing Management
T1  - Strukturne karakteristike galvanskih prevlaka bakra
T1  - Structural characteristics of electrodeposited copper coatings
VL  - 1
IS  - 2
SP  - 14
EP  - 25
ER  - 
@article{
author = "Tomić, M.V. and Pavlović, M.G. and Pavlović, Ljubica J. and Nikolić, Nebojša D.",
year = "2009",
url = "https://jepm.tfzv.ues.rs.ba/index.php/Journal/article/view/132, https://cer.ihtm.bg.ac.rs/handle/123456789/3926",
abstract = "Uzorci bakra su podvrgnuti mehaničkom i elektrohemijskom glačanju u odgovarajućim elektrolitima za elektrohemijsko glačanje. Na tako prethodno pripremljene površine supstrata izvršeno je taloţenje prevlaka bakra iz dva kupatila i to iz osnovnog elektrolita (OR) sastava: 240 g/dm3 CuSO4 ∙ 5 H2O + 60 g/dm3 H2SO4 i kupatila sa dodacima za sjaj (OR +DS). Pomoću STM i AFM tehnika precizno su prikazane strukturne osobine koje odreĎuju da li je metalna površina ogledalski sjajna ili ne, odnosno da li dobijena topografija površine manje ili više hrapava. UtvrĎeno je znatno povećanje hrapavosti uzoraka na koje je taloţena prevlaka bakra iz osnovnog sulfatnog kupatila (OR) u odnosu na mehanički i mehanički i elektrohemijske pripremane uzorke. TakoĎe, pri taloţenju prevlaka iz kupatila sa dodacima za sjaj (OR +DS), došlo je do smanjenja hrapavosti površine., The samples of rolled copper were mechanically and electrochemically polished in suitable electrolytes for electrochemical polishing. These substrate surfaces that had been prepared in advance, served as the basis for depositing of copper layers from two baths, namely, from the basic electrolyte(OR) with the following composition: 240 g/dm3 CuSO4 ∙ 5 H2O + 60 g/dm3 H2SO4i as well as from the bath which contained brightening addition agents(OR +DS). STM and AFM techniques show in great detail the structural properties which determine whether the metal surfaceis are as bright as a mirrior or not, that is, whether the obtained topography of the surface is more or less rough. It was determined that a considerable increase of roughness occurred in the samples where copper layers were deposited from the basic sulfate bath (OR) when compared with mechanical, and mechanical-electrochemical samples. In addition, depositing of the samples from the bath with brightening addition agents (OR +DS) resulted in the decrease of surface roughness.",
publisher = "Bosnia and Herzegovina : University of East Sarajevo, Faculty of Technology",
journal = "Journal of Engineering & Processing Management",
title = "Strukturne karakteristike galvanskih prevlaka bakra, Structural characteristics of electrodeposited copper coatings",
volume = "1",
number = "2",
pages = "14-25"
}
Tomić M, Pavlović M, Pavlović LJ, Nikolić ND. Structural characteristics of electrodeposited copper coatings. Journal of Engineering & Processing Management. 2009;1(2):14-25
Tomić, M.V., Pavlović, M.G., Pavlović, L. J.,& Nikolić, N. D. (2009). Structural characteristics of electrodeposited copper coatings.
Journal of Engineering & Processing ManagementBosnia and Herzegovina : University of East Sarajevo, Faculty of Technology., 1(2), 14-25.
Tomić M.V., Pavlović M.G., Pavlović Ljubica J., Nikolić Nebojša D., "Structural characteristics of electrodeposited copper coatings" 1, no. 2 (2009):14-25

DSpace software copyright © 2002-2015  DuraSpace
О Централном репозиторијуму (ЦеР) | Пошаљите запажања

OpenAIRERCUB
 

 

Комплетан репозиторијумИнституцијеАуториНасловиТемеОва институцијаАуториНасловиТеме

Статистика

Преглед статистика

DSpace software copyright © 2002-2015  DuraSpace
О Централном репозиторијуму (ЦеР) | Пошаљите запажања

OpenAIRERCUB