Приказ основних података о документу

Mikromehanička svojstva kompozitnih sistema formiranih elektrohemijskim taloženjem filmova nikla i bakra na različitim podlogama

dc.creatorLamovec, Jelena
dc.creatorJović, Vesna
dc.creatorMladenović, Ivana
dc.creatorVorkapić, Miloš
dc.creatorRadojević, Vesna
dc.creatorAleksić, Radoslav
dc.date.accessioned2019-01-30T17:31:47Z
dc.date.available2019-01-30T17:31:47Z
dc.date.issued2012
dc.identifier.issn0040-2176
dc.identifier.urihttps://cer.ihtm.bg.ac.rs/handle/123456789/1071
dc.description.abstractFine-grained nickel and copper thin films were electrodeposited (ED) from self-made sulphamate and sulphate electrolytes, respectively, on different substrates. The substrates were single crystal silicon with two different orientations, namely (100) and (111) and bulk electrodeposited Ni films. Nickel films on Si substrate and ED Cu films on bulk ED Ni substrate can be thought as composite systems of 'soft film on hard substrate' type. The influence of the substrate layer and chosen plating conditions on mechanical properties of these composite structures were investigated by Vickers microhardness testing for different loads. Above a certain critical penetration depth, a measured hardness value is not the hardness of the electrodeposited film, but the so-called 'composite hardness', because the substrate also participates in the plastic deformations during the indentation process. Composite hardness models of Jonsson-Hogmark (J-H), Burnett-Rickerby (B-R) and Korsunsky (K) do not fit experimental data for this type of composite system well. Chicot-Lesage (C-L) model based on the model for reinforced composites can be applied to experimental data even for the thick coatings (50 mm). Model (C-L) for reinforced composites was chosen for all specimen and the film hardness was calculated, for each indentation diagonal. The values obtained for the film hardness HF are influenced by the applied load. In case of the system of ED Ni film on Si substrate, film hardness lines have descending character, but in case of the ED Cu film on bulk ED Ni substrate, the film hardness increases. The variations should be related to physical phenomena such as the indentation size effect, the cracking in the neighborhood of the indent, the elastic contribution of the substrate for the lowest loads, or the crushing of the film for the highest loads.en
dc.description.abstractElektrohemijskim taloženjem (ET) tankih filmova Ni i Cu na različitim podlogama, monokristalnom silicijumu orijentacija (100) i (111) i masivnom elektrohemijski istaloženom filmu Ni, formirani su kompozitni sistemi tipa 'mekog filma na tvrdoj podlozi'. Sitnozrni talozi Ni i Cu su bili dobijeni iz dva različita elektrolita pod odabranim uslovima elektrolize, Ni iz sulfamatnog i Cu iz sulfatnog elektrolita.U cilju određivanja mehaničkih svojstava ovih kompozitnih sistema, i posebno, određivanja svojstava filmova u okviru sistema, izvršena su merenja mikrotvrdoće utiskivanjem po Vikersovoj metodi za različita opterećenja. Izmerena vrednost mikrotvrdoće opisuje kompozitni sistem u celini i naziva se 'kompozitnom mikrotvrdoćom'. Ona ne predstavlja apsolutnu tvrdoću elektrohemijski istaloženog filma zbog učešća podloge u plastičnoj deformaciji tokom utiskivanja. Model Šiko-Lezaža (Chicot-Lesage) se pokazao odgovarajućim za analizu apsolutne tvrdoće tankih filmova za kompozitne sisteme 'mek film na tvrdoj podlozi' i primenjen je na eksperimentalne rezultate.sr
dc.publisherSavez inženjera i tehničara Srbije
dc.relationinfo:eu-repo/grantAgreement/MESTD/Technological Development (TD or TR)/32008/RS//
dc.relationinfo:eu-repo/grantAgreement/MESTD/Technological Development (TD or TR)/34011/RS//
dc.relationinfo:eu-repo/grantAgreement/MESTD/Integrated and Interdisciplinary Research (IIR or III)/45019/RS//
dc.rightsopenAccess
dc.rights.urihttps://creativecommons.org/licenses/by/4.0/
dc.sourceTehnika
dc.subjectcomposite microhardnessen
dc.subjectVickers microhardness testen
dc.subjectabsolute hardness of electrodeposited filmsen
dc.subjectkompozitna tvrdoćasr
dc.subjectVikersov test utiskivanjemsr
dc.subjectapsolutna tvrdoća elektrohemijski istaloženih filmovasr
dc.titleMicromechanical properties of composite systems consisting of electrodeposited nickel coatings on different substratesen
dc.titleMikromehanička svojstva kompozitnih sistema formiranih elektrohemijskim taloženjem filmova nikla i bakra na različitim podlogamasr
dc.typearticle
dc.rights.licenseBY
dcterms.abstractВоркапић, Милош; Младеновић, Ивана; Радојевић, Весна; Јовић, Весна; Aлексић, Радослав Р.; Ламовец, Јелена; Микромеханичка својства композитних система формираних електрохемијским таложењем филмова никла и бакра на различитим подлогама; Микромеханичка својства композитних система формираних електрохемијским таложењем филмова никла и бакра на различитим подлогама;
dc.citation.volume67
dc.citation.issue1
dc.citation.spage9
dc.citation.epage15
dc.citation.other67(1): 9-15
dc.citation.rankM51
dc.identifier.rcubhttps://hdl.handle.net/21.15107/rcub_cer_1071
dc.identifier.fulltexthttps://cer.ihtm.bg.ac.rs//bitstream/id/7627/1069.pdf
dc.type.versionpublishedVersion


Документи

Thumbnail

Овај документ се појављује у следећим колекцијама

Приказ основних података о документу