Претраживање
Приказ резултата 1-10 од 91
Field applicable methods for intergranular corrosion testing of stainless steels structures / Metode ispitivanja interkristalne korozije na konstrukcijama od nerđajućh čelika na terenu
(Society for Structural Integrity and Life, 2016)
Determination of the susceptibility of austenitic stainless steel X5CrNi18-10 to intergranular corrosion (IGC) is performed by measuring the corrosion potential Ecorr in a drop of a test solution with specific chemical ...
Effect of chemical composition on microstructure, hardness and electrical conductivity profiles of the Bi-Cu-Ga alloys at 100 °C
(Serbia : Association of Metallurgical Engineers of Serbia, 2016)
Theoretical calculation and experimental investigation of the isothermal section of a ternary Bi-Cu-Ga system at 100 oC are presented in this paper. Thermodynamic binary-based calculation of the isothermal section was ...
Chemical corrosion of metals and alloys / Hemijska korozija metala i legura
(Belgrade, Serbia : Engineering Society for Corrosion, 2016)
In this paper, phenomena of chemical corrosion of metals and alloys in electrolyte solutions are analyzed. It is shown that iron, chromium and other metals and alloys dissolve much faster than is the corrosion rate determined ...
Determination of susceptibility to intergranular corrosion of stainless steels type X5CrNi18-10 in field
(Association of Metallurgical Engineers of Serbia, 2016)
In this paper, the DL EPR method (electrochemical potentiokinetic reactivation with double loop) was modified and used to study the susceptibility to intergranular corrosion and stress corrosion cracking of a stainless ...
Corrosion properties of an aluminium alloy 7000 series after a new two step precipitation hardening / Otpornost prema koroziji aluminijumske legure serije 7000 posle novog dvostepenog termičkog taloženja
(Belgrade, Serbia : Engineering Society for Corrosion, 2014)
Corrosion properties of an aluminium alloy 7000 series were investigated by different electrochemical methods. The alloy was subjected to the one-step and to a new two-step precipitation hardening. Polarization measurements ...
Modified tannins for alkyd based anticorrosive coatings / Primena modifikovanih tanina u antikorozionim alkidnim premazima
(Belgrade : Engineering Society for Corrosion, 2019)
The study of the synthesis of anticorrosive inhibitors, based on chemically modified tannins, and
their use in alkyd based coatings to improve anticorrosive properties is presented in this work.
Two methods of tannin ...
Mechanisms of hydrogen evolution on chromium / Mehanizmi izdvajanja vodonika na hromu
(Institut za rudarstvo i metalurgiju Bor, 2015)
In this work, the mechanisms of hydrogen evolution on the metal chromium in a solution of 0.1 M Na2SO4 + H2SO4, pH 1 to pH 7 were analysed. In the pH LT 3 range, hydrogen is evolved according to three different mechanisms, ...
The resistance to general corrosion of series of zinc-aluminum alloys modified with silicon and strontiumloys modified with silicon and strontium / Otpornost na opštu koroziju serije legura cink-aluminijum koje su modifikovane silicijumom i stroncijumom
(Belgrade : Engineering Society for Corrosion, 2019)
The resistance to corrosion of the series of zinc-aluminum casting alloys modified with silicon and
strontium was studied in a sodium chloride solution. It was shown that general corrosion was the
main form of corrosion ...
Testing the protective ability of corrosion inhibitors in dilute chloride solutions / Ispitivanje zaštitne sposobnosti inhibitora korozije u razblaženim rastvorima hlorida
(Belgrade, Serbia : Engineering Society for Corrosion, 2017)
After sterilization of meat cans in a factory of meat and meat products in Serbia, occurence of corrosion on the can lids was observed. Sterilization of cans is usually performed in the presence of corrosion inhibitors. ...
Determination of the weld metal corrosion rate using electrochemical techniques / Određivanje brzine korozije metala šava u zavarenom spoju pomoću elektrohemijskih tehnika
(Belgrade, Serbia : Engineering Society for Corrosion, 2015)
To determine corrosion rate of the base metal and weld metal were applied electrochemical techniques: linear polarization resistance, linear sweep voltammetry and electrochemical impedance spectroscopy. The samples were ...