TY  - CONF
AU  - Radojković, Bojana M.
AU  - Jegdić, Bore
AU  - Marunkić, Dunja D.
AU  - Pejić, Jovanka N.
PY  - 2022
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/5500
AB  - The efficacy of the environmentally friendly corrosion inhibitor Ce-citrate (0.1-0.5 mM) was analyzed on AISI 4130 low alloy carbon steel and AA7075 aluminum alloy in 0.05 M NaCl solution. Measurements of resistance to general corrosion were performed by electrochemical impedance spectroscopy and potentiodynamic polarization test. Resistance to pitting corrosion is determined based on the value of pitting potential Epit. For comparison, corrosion resistance measurements and pitting potential determination, for considered alloys, were performed in Ce-chloride solution. Changes on the surface of the specimens after corrosion testing were analyzed by SEM microscopy. The XPS method was used for the analyses of the formed inhibitory layer on the steel specimen surface. It has been shown that significant amounts of cerium, as well as the citrate anions, are present in the inhibitory layer. Ce-citrates have proved to be an effective corrosion inhibitor for AISI 4130 steel as well as an effective pitting corrosion inhibitor for AA7075 aluminum alloy. The mechanism of action of Ce-citrate on AISI 4130 steel and AA7075 aluminum alloy has been proposed.
T1  - Ce-citrate as green corrosion inhibitor for low alloy steel and aluminium alloys
UR  - https://hdl.handle.net/21.15107/rcub_cer_5500
ER  - 

@conference{
author = "Radojković, Bojana M. and Jegdić, Bore and Marunkić, Dunja D. and Pejić, Jovanka N.",
year = "2022",
abstract = "The efficacy of the environmentally friendly corrosion inhibitor Ce-citrate (0.1-0.5 mM) was analyzed on AISI 4130 low alloy carbon steel and AA7075 aluminum alloy in 0.05 M NaCl solution. Measurements of resistance to general corrosion were performed by electrochemical impedance spectroscopy and potentiodynamic polarization test. Resistance to pitting corrosion is determined based on the value of pitting potential Epit. For comparison, corrosion resistance measurements and pitting potential determination, for considered alloys, were performed in Ce-chloride solution. Changes on the surface of the specimens after corrosion testing were analyzed by SEM microscopy. The XPS method was used for the analyses of the formed inhibitory layer on the steel specimen surface. It has been shown that significant amounts of cerium, as well as the citrate anions, are present in the inhibitory layer. Ce-citrates have proved to be an effective corrosion inhibitor for AISI 4130 steel as well as an effective pitting corrosion inhibitor for AA7075 aluminum alloy. The mechanism of action of Ce-citrate on AISI 4130 steel and AA7075 aluminum alloy has been proposed.",
title = "Ce-citrate as green corrosion inhibitor for low alloy steel and aluminium alloys",
url = "https://hdl.handle.net/21.15107/rcub_cer_5500"
}

Radojković, B. M., Jegdić, B., Marunkić, D. D.,& Pejić, J. N.. (2022). Ce-citrate as green corrosion inhibitor for low alloy steel and aluminium alloys. .
https://hdl.handle.net/21.15107/rcub_cer_5500

Radojković BM, Jegdić B, Marunkić DD, Pejić JN. Ce-citrate as green corrosion inhibitor for low alloy steel and aluminium alloys. 2022;.
https://hdl.handle.net/21.15107/rcub_cer_5500 .

Radojković, Bojana M., Jegdić, Bore, Marunkić, Dunja D., Pejić, Jovanka N., "Ce-citrate as green corrosion inhibitor for low alloy steel and aluminium alloys" (2022),
https://hdl.handle.net/21.15107/rcub_cer_5500 .

TY  - CONF
AU  - Jarić, Marko
AU  - Petronić, Sanja
AU  - Marković, Saša
AU  - Trninić, Marta
AU  - Polić, Suzana R.
PY  - 2021
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/6218
AB  - Naftna platforma je velika građevina sa objektima za bušenje bušotina za istraživanje, vađenje, skladištenje i preradu nafte i prirodnog gasa koji leži u stenovitim formacijama ispod morskog dna. Bušenje na otvorenom moru predstavlja izazove za životnu sredinu. Iako, srećom, nije bilo mnogo nesreća na naftnim platformama, šteta koja nastane je ogromna i u ljudskom i u materijalnom i u smislu zaštite životne sredine. Iz tog razloga, inspekcija opreme pod pritiskom je od velikog značaja. Posude pod pritiskom mogu biti pod rizikom od degradacije materijala. Jedan od tipičnih mehanizama degradacije materijala je korozija. U ovom radu će biti prikazana važnost inspekcije opreme pod pritiskom. Na konkretnom, praktičnom primeru će biti predstavljena inspekcija cevovoda i određivanje brzine korozije i preostalog veka trajanja u cilju sprečavanja otkaza i materijalnih I ljudskih gubitaka.
AB  - The oil platform is a large structure with facilities for drilling wells for exploration, extraction, storage and refining of oil and natural gas lying in rock formations under the seabed. Offshore drilling poses environmental challenges. Although, fortunately, there have not been many accidents on oil platforms, the damage that occurs is enormous, both in human and material terms, and in terms of environmental protection. For that reason, the inspection of pressure equipment is of great importance. The risk to the pipeline in service can be failure due to material degradation. One of the typical mechanisms of material degradation is corrosion. This paper will present the importance of inspection of pressure equipment. On a concrete, practical example, pipeline inspection and determination of corrosion rate and remaining life will be presented in order to prevent failures and material and human losses.
PB  - Beograd: Savez mašinskih i elektrotehičkih inženjera i tehničara Srbije (SMEITS) = Belgrade:Union of Mechanical and Electrical Engineers and Technicians of Serbia
C3  - Proceedings - 9th International Conference on Renewable Electrical Power Sources, October 15, 2021, Belgrade
T1  - Važnost pregleda i određivanje preostalog veka trajanja cevovoda na naftnoj platformi
T1  - Importance of inspection and determination of remaining life of pipline in oil platform
SP  - 299
EP  - 304
UR  - https://hdl.handle.net/21.15107/rcub_cer_6218
ER  - 

@conference{
author = "Jarić, Marko and Petronić, Sanja and Marković, Saša and Trninić, Marta and Polić, Suzana R.",
year = "2021",
abstract = "Naftna platforma je velika građevina sa objektima za bušenje bušotina za istraživanje, vađenje, skladištenje i preradu nafte i prirodnog gasa koji leži u stenovitim formacijama ispod morskog dna. Bušenje na otvorenom moru predstavlja izazove za životnu sredinu. Iako, srećom, nije bilo mnogo nesreća na naftnim platformama, šteta koja nastane je ogromna i u ljudskom i u materijalnom i u smislu zaštite životne sredine. Iz tog razloga, inspekcija opreme pod pritiskom je od velikog značaja. Posude pod pritiskom mogu biti pod rizikom od degradacije materijala. Jedan od tipičnih mehanizama degradacije materijala je korozija. U ovom radu će biti prikazana važnost inspekcije opreme pod pritiskom. Na konkretnom, praktičnom primeru će biti predstavljena inspekcija cevovoda i određivanje brzine korozije i preostalog veka trajanja u cilju sprečavanja otkaza i materijalnih I ljudskih gubitaka., The oil platform is a large structure with facilities for drilling wells for exploration, extraction, storage and refining of oil and natural gas lying in rock formations under the seabed. Offshore drilling poses environmental challenges. Although, fortunately, there have not been many accidents on oil platforms, the damage that occurs is enormous, both in human and material terms, and in terms of environmental protection. For that reason, the inspection of pressure equipment is of great importance. The risk to the pipeline in service can be failure due to material degradation. One of the typical mechanisms of material degradation is corrosion. This paper will present the importance of inspection of pressure equipment. On a concrete, practical example, pipeline inspection and determination of corrosion rate and remaining life will be presented in order to prevent failures and material and human losses.",
publisher = "Beograd: Savez mašinskih i elektrotehičkih inženjera i tehničara Srbije (SMEITS) = Belgrade:Union of Mechanical and Electrical Engineers and Technicians of Serbia",
journal = "Proceedings - 9th International Conference on Renewable Electrical Power Sources, October 15, 2021, Belgrade",
title = "Važnost pregleda i određivanje preostalog veka trajanja cevovoda na naftnoj platformi, Importance of inspection and determination of remaining life of pipline in oil platform",
pages = "299-304",
url = "https://hdl.handle.net/21.15107/rcub_cer_6218"
}

Jarić, M., Petronić, S., Marković, S., Trninić, M.,& Polić, S. R.. (2021). Važnost pregleda i određivanje preostalog veka trajanja cevovoda na naftnoj platformi. in Proceedings - 9th International Conference on Renewable Electrical Power Sources, October 15, 2021, Belgrade
Beograd: Savez mašinskih i elektrotehičkih inženjera i tehničara Srbije (SMEITS) = Belgrade:Union of Mechanical and Electrical Engineers and Technicians of Serbia., 299-304.
https://hdl.handle.net/21.15107/rcub_cer_6218

Jarić M, Petronić S, Marković S, Trninić M, Polić SR. Važnost pregleda i određivanje preostalog veka trajanja cevovoda na naftnoj platformi. in Proceedings - 9th International Conference on Renewable Electrical Power Sources, October 15, 2021, Belgrade. 2021;:299-304.
https://hdl.handle.net/21.15107/rcub_cer_6218 .

Jarić, Marko, Petronić, Sanja, Marković, Saša, Trninić, Marta, Polić, Suzana R., "Važnost pregleda i određivanje preostalog veka trajanja cevovoda na naftnoj platformi" in Proceedings - 9th International Conference on Renewable Electrical Power Sources, October 15, 2021, Belgrade (2021):299-304,
https://hdl.handle.net/21.15107/rcub_cer_6218 .

TY  - JOUR
AU  - Linić, Suzana
AU  - Lučanin, Vojkan J.
AU  - Živković, Srđan P.
AU  - Raković, Marko
AU  - Ristić, Slavica S.
AU  - Radojković, Bojana
AU  - Polić, Suzana R.
PY  - 2021
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/4240
AB  - A multidisciplinary research method was employed with the intention to create a series of bio-inspired flattened airfoils, observe their aerodynamic characteristics, and analyse their applicability to small devices or to designs of high-speed trains, within the shortest period in the conceptual stage. A research specimen of a kingfisher, selected for biomimicry, was examined with the following methods: visual inspection, analysis of photographs, manufacturing quality control measurement with a 3D laser scanner, and microscopy. A basic multi-arc-line profile, re-engineered from the overlapped specimen shape data and based on the observations, was used for designing a series of seven derived airfoils. The aerodynamic characteristics of the bio-inspired airfoils were obtained with the panel methods at low and moderate subsonic speeds, while the small transonic difference method was used in the high-subsonic speed range. Basic and ellipse-like airfoils produce higher total drag at low and moderate velocities and higher forebody drag in the high-subsonic range when compared to derived and parabola-like airfoils. The obtained critical Mach numbers are in the range from 0.76 to 0.78, where three bionic airfoils show values equal to or smaller than the values of ellipse- and parabola-like airfoils. The profile with the shortest bio-inspired relative chord has a higher critical Mach number value than the parabola-like profile. The sonic lines above these profiles appear at close positions. The applied set of examination methods of the bio-inspired design is not time consuming and produces sufficiently good results in the conceptual stage. Therefore, a further development of unique and adjusted numerical methods and codes at pre-computational fluid dynamics run is encouraged, together with shape parameterization.
PB  - Springer Nature Switzerland AG 2020
T2  - Journal of the Brazilian Society of Mechanical Sciences and Engineering
T1  - Multidisciplinary research method for designing and selection of bio-inspired profiles in the conceptual designing stage
VL  - 43
IS  - 1
SP  - 57
DO  - 10.1007/s40430-020-02789-2
ER  - 

@article{
author = "Linić, Suzana and Lučanin, Vojkan J. and Živković, Srđan P. and Raković, Marko and Ristić, Slavica S. and Radojković, Bojana and Polić, Suzana R.",
year = "2021",
abstract = "A multidisciplinary research method was employed with the intention to create a series of bio-inspired flattened airfoils, observe their aerodynamic characteristics, and analyse their applicability to small devices or to designs of high-speed trains, within the shortest period in the conceptual stage. A research specimen of a kingfisher, selected for biomimicry, was examined with the following methods: visual inspection, analysis of photographs, manufacturing quality control measurement with a 3D laser scanner, and microscopy. A basic multi-arc-line profile, re-engineered from the overlapped specimen shape data and based on the observations, was used for designing a series of seven derived airfoils. The aerodynamic characteristics of the bio-inspired airfoils were obtained with the panel methods at low and moderate subsonic speeds, while the small transonic difference method was used in the high-subsonic speed range. Basic and ellipse-like airfoils produce higher total drag at low and moderate velocities and higher forebody drag in the high-subsonic range when compared to derived and parabola-like airfoils. The obtained critical Mach numbers are in the range from 0.76 to 0.78, where three bionic airfoils show values equal to or smaller than the values of ellipse- and parabola-like airfoils. The profile with the shortest bio-inspired relative chord has a higher critical Mach number value than the parabola-like profile. The sonic lines above these profiles appear at close positions. The applied set of examination methods of the bio-inspired design is not time consuming and produces sufficiently good results in the conceptual stage. Therefore, a further development of unique and adjusted numerical methods and codes at pre-computational fluid dynamics run is encouraged, together with shape parameterization.",
publisher = "Springer Nature Switzerland AG 2020",
journal = "Journal of the Brazilian Society of Mechanical Sciences and Engineering",
title = "Multidisciplinary research method for designing and selection of bio-inspired profiles in the conceptual designing stage",
volume = "43",
number = "1",
pages = "57",
doi = "10.1007/s40430-020-02789-2"
}

Linić, S., Lučanin, V. J., Živković, S. P., Raković, M., Ristić, S. S., Radojković, B.,& Polić, S. R.. (2021). Multidisciplinary research method for designing and selection of bio-inspired profiles in the conceptual designing stage. in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Springer Nature Switzerland AG 2020., 43(1), 57.
https://doi.org/10.1007/s40430-020-02789-2

Linić S, Lučanin VJ, Živković SP, Raković M, Ristić SS, Radojković B, Polić SR. Multidisciplinary research method for designing and selection of bio-inspired profiles in the conceptual designing stage. in Journal of the Brazilian Society of Mechanical Sciences and Engineering. 2021;43(1):57.
doi:10.1007/s40430-020-02789-2 .

Linić, Suzana, Lučanin, Vojkan J., Živković, Srđan P., Raković, Marko, Ristić, Slavica S., Radojković, Bojana, Polić, Suzana R., "Multidisciplinary research method for designing and selection of bio-inspired profiles in the conceptual designing stage" in Journal of the Brazilian Society of Mechanical Sciences and Engineering, 43, no. 1 (2021):57,
https://doi.org/10.1007/s40430-020-02789-2 . .

TY  - JOUR
AU  - Knežević, Dragan
AU  - Radojković, Bojana
AU  - Ristić, Slavica
AU  - Polić, Suzana R.
AU  - Janićijević, Milovan
AU  - Tomić, Ljubiša
AU  - Jegdić, Bore
PY  - 2021
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3978
AB  - Temperature  distribution  induced  by  laser  radiation  is  a  very  important 
parameter for an efficient and safe application of lasers in different ceramic 
processing  techniques.  This  paper  presents  the  results  of  an  infrared 
thermography (IRT) application for monitoring temperature distribution on 
a ceramic surface during Nd: YAG laser irradiation with different fluences 
and 8ns pulse duration. FLIR, E40 and SC7200 IR cameras were used with 
the  aim  of  recording  the  maximum  temperature  in  the  irradiated  zones.  It 
was  expected  that  IRT  could  give  some  information  related  to  the  heat 
affected zone and possible damage to the base material; however, the results 
have  shown  that  IR  cameras,  even  those  with  high  performance  such  as 
SC7200,  cannot  record  the  maximum  temperature  value  at  the  moment  of 
laser  operation,  but  only  the  average  temperature  of  the  bulk  sample 
material  after  laser  pulses.  The  results  of  the  numerical  simulation  have 
confirmed the value of the thermographic measurements. The microstructure 
and  micromorphology  of  the  ceramic  surface  before  and  after  the  laser 
treatment  were  analysed  by  optical  and  scanning  electron  microscopy  as 
well  as  by  examining  the  roughness  of  the  irradiated  and  non-  irradiated 
surfaces,  while  the  micromechanical  changes  were  analysed  by  comparing 
the micro-hardness of the irradiated and non-exposed surfaces.
PB  - Vinča Institute of Nuclear Sciences, Belgrade
T2  - Thermal Science
T1  - Monitoring of a ceramic surface temperature field induced by pulsed Nd: YAG laser
VL  - 25
IS  - 1B
SP  - 567
EP  - 578
DO  - 10.2298/TSCI190811425K
ER  - 

@article{
author = "Knežević, Dragan and Radojković, Bojana and Ristić, Slavica and Polić, Suzana R. and Janićijević, Milovan and Tomić, Ljubiša and Jegdić, Bore",
year = "2021",
abstract = "Temperature  distribution  induced  by  laser  radiation  is  a  very  important 
parameter for an efficient and safe application of lasers in different ceramic 
processing  techniques.  This  paper  presents  the  results  of  an  infrared 
thermography (IRT) application for monitoring temperature distribution on 
a ceramic surface during Nd: YAG laser irradiation with different fluences 
and 8ns pulse duration. FLIR, E40 and SC7200 IR cameras were used with 
the  aim  of  recording  the  maximum  temperature  in  the  irradiated  zones.  It 
was  expected  that  IRT  could  give  some  information  related  to  the  heat 
affected zone and possible damage to the base material; however, the results 
have  shown  that  IR  cameras,  even  those  with  high  performance  such  as 
SC7200,  cannot  record  the  maximum  temperature  value  at  the  moment  of 
laser  operation,  but  only  the  average  temperature  of  the  bulk  sample 
material  after  laser  pulses.  The  results  of  the  numerical  simulation  have 
confirmed the value of the thermographic measurements. The microstructure 
and  micromorphology  of  the  ceramic  surface  before  and  after  the  laser 
treatment  were  analysed  by  optical  and  scanning  electron  microscopy  as 
well  as  by  examining  the  roughness  of  the  irradiated  and  non-  irradiated 
surfaces,  while  the  micromechanical  changes  were  analysed  by  comparing 
the micro-hardness of the irradiated and non-exposed surfaces.",
publisher = "Vinča Institute of Nuclear Sciences, Belgrade",
journal = "Thermal Science",
title = "Monitoring of a ceramic surface temperature field induced by pulsed Nd: YAG laser",
volume = "25",
number = "1B",
pages = "567-578",
doi = "10.2298/TSCI190811425K"
}

Knežević, D., Radojković, B., Ristić, S., Polić, S. R., Janićijević, M., Tomić, L.,& Jegdić, B.. (2021). Monitoring of a ceramic surface temperature field induced by pulsed Nd: YAG laser. in Thermal Science
Vinča Institute of Nuclear Sciences, Belgrade., 25(1B), 567-578.
https://doi.org/10.2298/TSCI190811425K

Knežević D, Radojković B, Ristić S, Polić SR, Janićijević M, Tomić L, Jegdić B. Monitoring of a ceramic surface temperature field induced by pulsed Nd: YAG laser. in Thermal Science. 2021;25(1B):567-578.
doi:10.2298/TSCI190811425K .

Knežević, Dragan, Radojković, Bojana, Ristić, Slavica, Polić, Suzana R., Janićijević, Milovan, Tomić, Ljubiša, Jegdić, Bore, "Monitoring of a ceramic surface temperature field induced by pulsed Nd: YAG laser" in Thermal Science, 25, no. 1B (2021):567-578,
https://doi.org/10.2298/TSCI190811425K . .

TY  - JOUR
AU  - Срећковић, Милеса
AU  - Polić, Suzana R.
AU  - Ивковић, Миливоје
AU  - Карастојковић, Зоран
AU  - Винић, Милица
AU  - Ковачевић, Александер
AU  - Бојанић, Слободан
PY  - 2020
UR  - http://idk.org.rs/brojevi-casopisa/izdanja-2020-godine/zastita-materijala-4-2020/
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/4064
AB  - It seems that the role of lasers in heritology and art has grown more and more since the end of the 
20 th   century;  the  early  attempts  of cleaning  artistic  objects,  old  monuments  /  artifacts  during  the 
times of Hedy Lamarr and the first unsuccessful nuclear tests as well as of thinking of holographic 
records.  After  the  first  series  of  circumstances  linked  to  laser  applications  in  restoration  and 
conservation,  it  seems  the  coupling  of  words  serendipity-zemblanity-bahramdipity  has  been 
activated.  A  long  time  has  passed  since  the  first  works  linked  to  the  Porta  della  carte  of  the 
Palazzo Ducale (Doge’s Palace) in Venice (marble relief and ruby laser). Nowadays, this type of 
work can be treated as standardized and it is implemented in great number of countries [1, 2]. In 
the  case  of  Florence  Cathedral,  the  conservation  of  artworks  was  proposed  by  J.  F.  Fonatello, 
panels of the Giotto’s tower of the Florence Cathedral by Andrea Pisano. 
The  unique  roles  of  quantum  generators  –  lasers  –    exist  both  in  restoration  and  diagnostics. 
Besides  that,  the  question  of  source  existence  –  a  source  that  provides  completely  new  artistic 
impression  with  respect  to  its  ideal  characteristic  of  coherency  –  introduced  new  tools  and 
techniques and could be (and was) implemented in many new processes and effects. New artistic 
directions  were  performed,  where  the  source  of  the  coherence  became  a  part  of  a  new  artistic 
object, a hologram slide provokes the impression of the train entering the crowd, etc. [1–5] The 
laser role by using LIBS method in diagnostics in the case of the building in 7 Balkanska street, 
Belgrade, was presented in this paper.
AB  - Čini se da je uloga lasera u heritologiji i umetnosti u stalnom porastu od kraja 20. veka; rani su pokušaji čišćenja umetničkih objekata, starih spomenika ili artefakata od vremena Hedi Lamar (Hedy Lamarr) i prvih neuspešnih nuklearnih testova, kao i razmišljanja o holografskim zapisima. Posle prve serije okolnosti vezanih za primene laserskih tehnika u restauraciji i konzervaciji, izgleda da je sprezanje reči serendipity, zemblanity i bahramdipity aktivirano. Prošlo je mnogo vremena otkad su obavljeni prvi radovi vezani za Porta della Carta Duždeve palate (Palazzo Ducale) u Veneciji – mermerni reljef i rubinski laser. Danas ovaj tip radova može da se tretira kao konvencionalan/standardan i primeni u nizu zemalja [1, 2]. U slučaju Katedrale u Firenci Fonatelo (J. F. Fonatello) je predložio konzervaciju umetničkih objekata, Pizanove (Andrea Pisano) panele na Đotovoj (Giotto) kuli Katedrale.

Jedinstvene uloge kvantnih generatora – lasera – postoje i u restauraciji i u dijagnostici. Osim toga, pitanje postojanja izvora – izvora koji nudi potpuno novi umetnički utisak u odnosu na idealne osobine koherencije – uvelo je nove alate i tehnike i moglo je da (i jeste) primeni mnogo novih procesa i efekata. Novi umetnički pravci su izvedeni, gde je izvor koherencije postao deo novog umetničkog objekta, hologram je izazvao utisak da voz ulazi u masu ljudi, itd. [1–5] Uloga lasera u dijagnostici i u svrhu konzervacije i neke primene na slučaj zgrade u Balkanskoj 7 u Beogradu je prikazana u ovom radu.
PB  - Inženjersko društvo za koroziju
T2  - Zaštita materijala
T1  - Contemporary laser techniques and general application in heritology and case of building in 7 Balkanska street, Belgrade
T1  - Savremene laserske tehnike i opšta primena u heritologiji i slučaj zgrade u balkanskoj ulici 7, Beograd
VL  - 61
IS  - 4
SP  - 275
EP  - 285
DO  - 10.5937/zasmat2004275S
ER  - 

@article{
author = "Срећковић, Милеса and Polić, Suzana R. and Ивковић, Миливоје and Карастојковић, Зоран and Винић, Милица and Ковачевић, Александер and Бојанић, Слободан",
year = "2020",
abstract = "It seems that the role of lasers in heritology and art has grown more and more since the end of the 
20 th   century;  the  early  attempts  of cleaning  artistic  objects,  old  monuments  /  artifacts  during  the 
times of Hedy Lamarr and the first unsuccessful nuclear tests as well as of thinking of holographic 
records.  After  the  first  series  of  circumstances  linked  to  laser  applications  in  restoration  and 
conservation,  it  seems  the  coupling  of  words  serendipity-zemblanity-bahramdipity  has  been 
activated.  A  long  time  has  passed  since  the  first  works  linked  to  the  Porta  della  carte  of  the 
Palazzo Ducale (Doge’s Palace) in Venice (marble relief and ruby laser). Nowadays, this type of 
work can be treated as standardized and it is implemented in great number of countries [1, 2]. In 
the  case  of  Florence  Cathedral,  the  conservation  of  artworks  was  proposed  by  J.  F.  Fonatello, 
panels of the Giotto’s tower of the Florence Cathedral by Andrea Pisano. 
The  unique  roles  of  quantum  generators  –  lasers  –    exist  both  in  restoration  and  diagnostics. 
Besides  that,  the  question  of  source  existence  –  a  source  that  provides  completely  new  artistic 
impression  with  respect  to  its  ideal  characteristic  of  coherency  –  introduced  new  tools  and 
techniques and could be (and was) implemented in many new processes and effects. New artistic 
directions  were  performed,  where  the  source  of  the  coherence  became  a  part  of  a  new  artistic 
object, a hologram slide provokes the impression of the train entering the crowd, etc. [1–5] The 
laser role by using LIBS method in diagnostics in the case of the building in 7 Balkanska street, 
Belgrade, was presented in this paper., Čini se da je uloga lasera u heritologiji i umetnosti u stalnom porastu od kraja 20. veka; rani su pokušaji čišćenja umetničkih objekata, starih spomenika ili artefakata od vremena Hedi Lamar (Hedy Lamarr) i prvih neuspešnih nuklearnih testova, kao i razmišljanja o holografskim zapisima. Posle prve serije okolnosti vezanih za primene laserskih tehnika u restauraciji i konzervaciji, izgleda da je sprezanje reči serendipity, zemblanity i bahramdipity aktivirano. Prošlo je mnogo vremena otkad su obavljeni prvi radovi vezani za Porta della Carta Duždeve palate (Palazzo Ducale) u Veneciji – mermerni reljef i rubinski laser. Danas ovaj tip radova može da se tretira kao konvencionalan/standardan i primeni u nizu zemalja [1, 2]. U slučaju Katedrale u Firenci Fonatelo (J. F. Fonatello) je predložio konzervaciju umetničkih objekata, Pizanove (Andrea Pisano) panele na Đotovoj (Giotto) kuli Katedrale.

Jedinstvene uloge kvantnih generatora – lasera – postoje i u restauraciji i u dijagnostici. Osim toga, pitanje postojanja izvora – izvora koji nudi potpuno novi umetnički utisak u odnosu na idealne osobine koherencije – uvelo je nove alate i tehnike i moglo je da (i jeste) primeni mnogo novih procesa i efekata. Novi umetnički pravci su izvedeni, gde je izvor koherencije postao deo novog umetničkog objekta, hologram je izazvao utisak da voz ulazi u masu ljudi, itd. [1–5] Uloga lasera u dijagnostici i u svrhu konzervacije i neke primene na slučaj zgrade u Balkanskoj 7 u Beogradu je prikazana u ovom radu.",
publisher = "Inženjersko društvo za koroziju",
journal = "Zaštita materijala",
title = "Contemporary laser techniques and general application in heritology and case of building in 7 Balkanska street, Belgrade, Savremene laserske tehnike i opšta primena u heritologiji i slučaj zgrade u balkanskoj ulici 7, Beograd",
volume = "61",
number = "4",
pages = "275-285",
doi = "10.5937/zasmat2004275S"
}

Срећковић, М., Polić, S. R., Ивковић, М., Карастојковић, З., Винић, М., Ковачевић, А.,& Бојанић, С.. (2020). Contemporary laser techniques and general application in heritology and case of building in 7 Balkanska street, Belgrade. in Zaštita materijala
Inženjersko društvo za koroziju., 61(4), 275-285.
https://doi.org/10.5937/zasmat2004275S

Срећковић М, Polić SR, Ивковић М, Карастојковић З, Винић М, Ковачевић А, Бојанић С. Contemporary laser techniques and general application in heritology and case of building in 7 Balkanska street, Belgrade. in Zaštita materijala. 2020;61(4):275-285.
doi:10.5937/zasmat2004275S .

Срећковић, Милеса, Polić, Suzana R., Ивковић, Миливоје, Карастојковић, Зоран, Винић, Милица, Ковачевић, Александер, Бојанић, Слободан, "Contemporary laser techniques and general application in heritology and case of building in 7 Balkanska street, Belgrade" in Zaštita materijala, 61, no. 4 (2020):275-285,
https://doi.org/10.5937/zasmat2004275S . .

TY  - JOUR
AU  - Radojković, Bojana
AU  - Jegdić, Bore
AU  - Bobić, Biljana
AU  - Ristić, Slavica R.
AU  - Polić, Suzana R.
PY  - 2020
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3462
AB  - Nd:YAG laser was used for cleaning surfaces of cultural heritage iron artefacts covered with
corrosion products. The corrosion products were removed without damaging the base material.
Three different electrochemical techniques were used for the determination of the corrosion rate of
mechanically prepared iron, laser-cleaned iron and laser-cleaned iron with Paraloid B44 coating.
The morphology of the tested surfaces was analysed by SEM. The linear polarization resistance
technique, electrochemical impedance spectroscopy and linear sweep voltammetry have shown
that the corrosion rate of the laser-cleaned iron is approximately 50 % higher than the corrosion
rate of the mechanically prepared iron. Electrochemical impedance spectroscopy has shown that
the pore resistance of the Paraloid coating on the laser-cleaned iron sample decreases at the
beginning of the test and remains approximately constant after this period. At the beginning of the
test, the charge transfer resistance value is constant and then decreases rapidly i.e. the corrosion
rate of the iron in the Paraloid coating pores increases with time. During the linear sweep
voltammetry test of the iron sample with Paraloid coating, it was noticed that the anodic
polarisation curve shows an unusual shape at the potentials more positive than - 0.5 V
AB  - U ovom radu, Nd:YAG laser je korišćen za čišćenje površina artefakata od gvožđa koji su bili prekriveni korozionim produktima. Korozioni produkti su uklonjeni bez oštećivanja osnovnog materijala. Za određivanje brzine korozije mehanički čišćene površine, laserski čišćene površine i laserski čišćene površine na koju je nakon čišćenja nanesen zaštitni sloj Paraloid B44, korišćene su tri različite elektrohemijske metode. Morfologija čišćenih površina je ispitivana SEM mikroskopijom. Metoda linearne polarizacione otpornosti, elektrohemijska impedansna spektroskopija i voltametrija sa linearnom promenom potencijala pokazale su da je brzina korozije laserski čišćene površine uzorka od gvožđa za oko 50% veća od brzine korozije mehanički čišćene površine. Elektrohemijska impedansna spektroskopija je pokazala da otpornost pora Paraloid prevlake na laserski čišćenoj površini uzorka opada na početku ispitivanja nakon čega dostiže konstantnu vrednost. Na početku ispitivanja, vrednost otpornosti razmeni elektrona je konstantna nakon čega naglo opada, tj. brzina korozije gvožđa u porama Paraloid prevlake raste sa vremenom. Tokom ispitivanja tehnikom voltametrije sa linearnom promenom potencijala na uzorku od gvožđa sa Paraloid prevlakom, zapaženo je da anodna kriva polarizacije ima neuobičajen oblik pri potencijalima pozitivnijim od - 0.5 V
PB  - Belgrade : Engineering Society for Corrosion
T2  - Zaštita materijala
T1  - Corrosion characteristics of laser-cleaned surfaces on iron artefact
T1  - Koroziona svojstva laserski čišćenih površina na artefaktu od gvožđa
VL  - 61
IS  - 1
SP  - 41
EP  - 51
DO  - 10.5937/zasmat2001041R
ER  - 

@article{
author = "Radojković, Bojana and Jegdić, Bore and Bobić, Biljana and Ristić, Slavica R. and Polić, Suzana R.",
year = "2020",
abstract = "Nd:YAG laser was used for cleaning surfaces of cultural heritage iron artefacts covered with
corrosion products. The corrosion products were removed without damaging the base material.
Three different electrochemical techniques were used for the determination of the corrosion rate of
mechanically prepared iron, laser-cleaned iron and laser-cleaned iron with Paraloid B44 coating.
The morphology of the tested surfaces was analysed by SEM. The linear polarization resistance
technique, electrochemical impedance spectroscopy and linear sweep voltammetry have shown
that the corrosion rate of the laser-cleaned iron is approximately 50 % higher than the corrosion
rate of the mechanically prepared iron. Electrochemical impedance spectroscopy has shown that
the pore resistance of the Paraloid coating on the laser-cleaned iron sample decreases at the
beginning of the test and remains approximately constant after this period. At the beginning of the
test, the charge transfer resistance value is constant and then decreases rapidly i.e. the corrosion
rate of the iron in the Paraloid coating pores increases with time. During the linear sweep
voltammetry test of the iron sample with Paraloid coating, it was noticed that the anodic
polarisation curve shows an unusual shape at the potentials more positive than - 0.5 V, U ovom radu, Nd:YAG laser je korišćen za čišćenje površina artefakata od gvožđa koji su bili prekriveni korozionim produktima. Korozioni produkti su uklonjeni bez oštećivanja osnovnog materijala. Za određivanje brzine korozije mehanički čišćene površine, laserski čišćene površine i laserski čišćene površine na koju je nakon čišćenja nanesen zaštitni sloj Paraloid B44, korišćene su tri različite elektrohemijske metode. Morfologija čišćenih površina je ispitivana SEM mikroskopijom. Metoda linearne polarizacione otpornosti, elektrohemijska impedansna spektroskopija i voltametrija sa linearnom promenom potencijala pokazale su da je brzina korozije laserski čišćene površine uzorka od gvožđa za oko 50% veća od brzine korozije mehanički čišćene površine. Elektrohemijska impedansna spektroskopija je pokazala da otpornost pora Paraloid prevlake na laserski čišćenoj površini uzorka opada na početku ispitivanja nakon čega dostiže konstantnu vrednost. Na početku ispitivanja, vrednost otpornosti razmeni elektrona je konstantna nakon čega naglo opada, tj. brzina korozije gvožđa u porama Paraloid prevlake raste sa vremenom. Tokom ispitivanja tehnikom voltametrije sa linearnom promenom potencijala na uzorku od gvožđa sa Paraloid prevlakom, zapaženo je da anodna kriva polarizacije ima neuobičajen oblik pri potencijalima pozitivnijim od - 0.5 V",
publisher = "Belgrade : Engineering Society for Corrosion",
journal = "Zaštita materijala",
title = "Corrosion characteristics of laser-cleaned surfaces on iron artefact, Koroziona svojstva laserski čišćenih površina na artefaktu od gvožđa",
volume = "61",
number = "1",
pages = "41-51",
doi = "10.5937/zasmat2001041R"
}

Radojković, B., Jegdić, B., Bobić, B., Ristić, S. R.,& Polić, S. R.. (2020). Corrosion characteristics of laser-cleaned surfaces on iron artefact. in Zaštita materijala
Belgrade : Engineering Society for Corrosion., 61(1), 41-51.
https://doi.org/10.5937/zasmat2001041R

Radojković B, Jegdić B, Bobić B, Ristić SR, Polić SR. Corrosion characteristics of laser-cleaned surfaces on iron artefact. in Zaštita materijala. 2020;61(1):41-51.
doi:10.5937/zasmat2001041R .

Radojković, Bojana, Jegdić, Bore, Bobić, Biljana, Ristić, Slavica R., Polić, Suzana R., "Corrosion characteristics of laser-cleaned surfaces on iron artefact" in Zaštita materijala, 61, no. 1 (2020):41-51,
https://doi.org/10.5937/zasmat2001041R . .

TY  - JOUR
AU  - Jegdić, Bore
AU  - Bobić, Biljana
AU  - Stevanović, Maja
AU  - Mihailović, Marija
AU  - Daničić, Dunja
AU  - Kovačina, Jovanka
AU  - Radojković, Bojana
PY  - 2020
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3649
AB  - The paper analyses the corrosion behaviour of both naturally and artificially aged AA2024 aluminium alloy in NaCl solution in the presence of the corrosion inhibitor benzotriazole (BTA). The differences between these two aging tempers in terms of resistance to general corrosion are explained as well as the differences in terms of pit formation and pit growth. Based on the values of the polarisation resistance and the corrosion current density, the general corrosion resistance of the alloy is determined in the absence and in the presence of BTA. The resistance to pit formation and pit growth is determined on the basis of the polarisation measurements results. Scanning electron microscopy confirmed the expected differences in the appearance and size of the pits formed in naturally aged and artificially aged alloy. In the presence of the corrosion inhibitor BTA, for both aging tempers of the alloy, the corrosion resistance is significantly higher compared to the resistance in the solution without the inhibitor. The value of the polarisation resistance for both aging tempers increases over time. However, at the same time, the value of the constant phase element increases as well. An explanation for this phenomenon is provided. The calculated average value of the thickness of the adsorbed inhibitor layer on the surface of the aluminium alloy is in accordance with the inhibitor protective ability for both aging tempers.
PB  - Springer
T2  - Metals and Materials International
T1  - Resistance to Pit Formation and Pit Growth for Different Tempers of AA2024 Aluminium Alloy in Presence of Benzotriazole
VL  - 26
SP  - 1643
EP  - 1653
DO  - 10.1007/s12540-019-00451-8
ER  - 

@article{
author = "Jegdić, Bore and Bobić, Biljana and Stevanović, Maja and Mihailović, Marija and Daničić, Dunja and Kovačina, Jovanka and Radojković, Bojana",
year = "2020",
abstract = "The paper analyses the corrosion behaviour of both naturally and artificially aged AA2024 aluminium alloy in NaCl solution in the presence of the corrosion inhibitor benzotriazole (BTA). The differences between these two aging tempers in terms of resistance to general corrosion are explained as well as the differences in terms of pit formation and pit growth. Based on the values of the polarisation resistance and the corrosion current density, the general corrosion resistance of the alloy is determined in the absence and in the presence of BTA. The resistance to pit formation and pit growth is determined on the basis of the polarisation measurements results. Scanning electron microscopy confirmed the expected differences in the appearance and size of the pits formed in naturally aged and artificially aged alloy. In the presence of the corrosion inhibitor BTA, for both aging tempers of the alloy, the corrosion resistance is significantly higher compared to the resistance in the solution without the inhibitor. The value of the polarisation resistance for both aging tempers increases over time. However, at the same time, the value of the constant phase element increases as well. An explanation for this phenomenon is provided. The calculated average value of the thickness of the adsorbed inhibitor layer on the surface of the aluminium alloy is in accordance with the inhibitor protective ability for both aging tempers.",
publisher = "Springer",
journal = "Metals and Materials International",
title = "Resistance to Pit Formation and Pit Growth for Different Tempers of AA2024 Aluminium Alloy in Presence of Benzotriazole",
volume = "26",
pages = "1643-1653",
doi = "10.1007/s12540-019-00451-8"
}

Jegdić, B., Bobić, B., Stevanović, M., Mihailović, M., Daničić, D., Kovačina, J.,& Radojković, B.. (2020). Resistance to Pit Formation and Pit Growth for Different Tempers of AA2024 Aluminium Alloy in Presence of Benzotriazole. in Metals and Materials International
Springer., 26, 1643-1653.
https://doi.org/10.1007/s12540-019-00451-8

Jegdić B, Bobić B, Stevanović M, Mihailović M, Daničić D, Kovačina J, Radojković B. Resistance to Pit Formation and Pit Growth for Different Tempers of AA2024 Aluminium Alloy in Presence of Benzotriazole. in Metals and Materials International. 2020;26:1643-1653.
doi:10.1007/s12540-019-00451-8 .

Jegdić, Bore, Bobić, Biljana, Stevanović, Maja, Mihailović, Marija, Daničić, Dunja, Kovačina, Jovanka, Radojković, Bojana, "Resistance to Pit Formation and Pit Growth for Different Tempers of AA2024 Aluminium Alloy in Presence of Benzotriazole" in Metals and Materials International, 26 (2020):1643-1653,
https://doi.org/10.1007/s12540-019-00451-8 . .

TY  - GEN
AU  - Radojković, Bojana
AU  - Jegdić, Bore
AU  - Kovačina, Jovanka
AU  - Stevanović, Sanja
AU  - Marunkić, Dunja
PY  - 2020
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/5501
T1  - Микроструктура, храпавост и отпорност на корозију завареног споја аустенитног нерђајућег челика AISI 304L
UR  - https://hdl.handle.net/21.15107/rcub_cer_5501
ER  - 

@misc{
author = "Radojković, Bojana and Jegdić, Bore and Kovačina, Jovanka and Stevanović, Sanja and Marunkić, Dunja",
year = "2020",
title = "Микроструктура, храпавост и отпорност на корозију завареног споја аустенитног нерђајућег челика AISI 304L",
url = "https://hdl.handle.net/21.15107/rcub_cer_5501"
}

Radojković, B., Jegdić, B., Kovačina, J., Stevanović, S.,& Marunkić, D.. (2020). Микроструктура, храпавост и отпорност на корозију завареног споја аустенитног нерђајућег челика AISI 304L. .
https://hdl.handle.net/21.15107/rcub_cer_5501

Radojković B, Jegdić B, Kovačina J, Stevanović S, Marunkić D. Микроструктура, храпавост и отпорност на корозију завареног споја аустенитног нерђајућег челика AISI 304L. 2020;.
https://hdl.handle.net/21.15107/rcub_cer_5501 .

Radojković, Bojana, Jegdić, Bore, Kovačina, Jovanka, Stevanović, Sanja, Marunkić, Dunja, "Микроструктура, храпавост и отпорност на корозију завареног споја аустенитног нерђајућег челика AISI 304L" (2020),
https://hdl.handle.net/21.15107/rcub_cer_5501 .

TY  - JOUR
AU  - Jegdić, Bore
AU  - Bobić, Biljana
AU  - Linić, Suzana
PY  - 2020
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3723
AB  - The paper analyses the corrosion behaviour of naturally and artificially aged
AA2024 alloy in NaCl solution and in the presence of an environment ‐ friendly
corrosion inhibitor, CeCl 3 . On the basis of the values of polarisation resistance
and  corrosion  current  density,  the  corrosion  resistance  of  the  protective
inhibitor film is established as well as the general corrosion resistance of this
aluminium  alloy.  Resistance  to  pit  formation  is  determined  based  on  the
difference in pitting and corrosion potentials while resistance to pit growth is
determined based on the amount of charge consumed during pit growth. A
scanning electron microscope is used to examine the morphology of the pits
formed during the pitting corrosion testing, as well as to determine the cerium
content on intermetallic particles and the matrix AA2024 alloy. The corrosion
behaviour of AA2024 alloy is investigated after different test periods in NaCl
solution  and  in  the  same  solution  with  the  CeCl 3 inhibitor.  The  corrosion
resistance of both tempers of AA2024 alloy is more than one order of magnitude
higher in the presence of CeCl 3 . An explanation of the observed differences in
the corrosion behaviour of the naturally and artificially aged AA2024 alloy is
proposed. Different corrosion behaviour of the alloy after different test periods
is also explained.
PB  - Wiley - VCH Verlag GmbH & Co
T2  - Materials and Corrosion
T1  - Corrosion behaviour of AA2024 aluminium alloy in different tempers in NaCl solution and with the CeCl3 corrosion inhibitor
VL  - 71
IS  - 3
SP  - 352
EP  - 364
DO  - 10.1002/maco.201911219
ER  - 

@article{
author = "Jegdić, Bore and Bobić, Biljana and Linić, Suzana",
year = "2020",
abstract = "The paper analyses the corrosion behaviour of naturally and artificially aged
AA2024 alloy in NaCl solution and in the presence of an environment ‐ friendly
corrosion inhibitor, CeCl 3 . On the basis of the values of polarisation resistance
and  corrosion  current  density,  the  corrosion  resistance  of  the  protective
inhibitor film is established as well as the general corrosion resistance of this
aluminium  alloy.  Resistance  to  pit  formation  is  determined  based  on  the
difference in pitting and corrosion potentials while resistance to pit growth is
determined based on the amount of charge consumed during pit growth. A
scanning electron microscope is used to examine the morphology of the pits
formed during the pitting corrosion testing, as well as to determine the cerium
content on intermetallic particles and the matrix AA2024 alloy. The corrosion
behaviour of AA2024 alloy is investigated after different test periods in NaCl
solution  and  in  the  same  solution  with  the  CeCl 3 inhibitor.  The  corrosion
resistance of both tempers of AA2024 alloy is more than one order of magnitude
higher in the presence of CeCl 3 . An explanation of the observed differences in
the corrosion behaviour of the naturally and artificially aged AA2024 alloy is
proposed. Different corrosion behaviour of the alloy after different test periods
is also explained.",
publisher = "Wiley - VCH Verlag GmbH & Co",
journal = "Materials and Corrosion",
title = "Corrosion behaviour of AA2024 aluminium alloy in different tempers in NaCl solution and with the CeCl3 corrosion inhibitor",
volume = "71",
number = "3",
pages = "352-364",
doi = "10.1002/maco.201911219"
}

Jegdić, B., Bobić, B.,& Linić, S.. (2020). Corrosion behaviour of AA2024 aluminium alloy in different tempers in NaCl solution and with the CeCl3 corrosion inhibitor. in Materials and Corrosion
Wiley - VCH Verlag GmbH & Co., 71(3), 352-364.
https://doi.org/10.1002/maco.201911219

Jegdić B, Bobić B, Linić S. Corrosion behaviour of AA2024 aluminium alloy in different tempers in NaCl solution and with the CeCl3 corrosion inhibitor. in Materials and Corrosion. 2020;71(3):352-364.
doi:10.1002/maco.201911219 .

Jegdić, Bore, Bobić, Biljana, Linić, Suzana, "Corrosion behaviour of AA2024 aluminium alloy in different tempers in NaCl solution and with the CeCl3 corrosion inhibitor" in Materials and Corrosion, 71, no. 3 (2020):352-364,
https://doi.org/10.1002/maco.201911219 . .

TY  - JOUR
AU  - Vencl, Aleksandar
AU  - Bobić, Ilija
AU  - Stanković, Miloš
AU  - Hvizdoš, Pavol
AU  - Bobić, Biljana
AU  - Stojanović, Blaža
AU  - Franek, Friedrich
PY  - 2020
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3437
AB  - Metal matrix composites are very inhomogeneous materials, and their properties depend on various parameters (production process, constituents, their interfaces, etc.). The influence of SiC microparticles (40 mu m) reinforcement and graphite macroparticles (200-800 mu m) addition on the mechanical properties of Al-Si A356 alloy, produced by compocasting, has been assessed using macro- and nanoscale measurements of hardness and modulus of elasticity. The Al makes over 90 wt% of the A356 alloy, so the nanoscale measurements were performed on different alpha phase regions on each material (core of alpha phase, eutectic alpha phase, and alpha phase near the phase boundaries alpha phase/secondary phases). The results showed that there is no direct correlation between mechanical properties on macro- and nanoscale. The nanoscale results also showed that the secondary phases (SiC and graphite particles) can have significant effect on the mechanical properties on the atomic level, i.e. in the alpha phase regions very close to the secondary phases.
PB  - Springer
T2  - Journal of the Brazilian Society of Mechanical Sciences and Engineering
T1  - Influence of secondary phases in A356 MMCs on their mechanical properties at macro- and nanoscale
VL  - 42
IS  - 3
SP  - 115
DO  - 10.1007/s40430-020-2197-6
ER  - 

@article{
author = "Vencl, Aleksandar and Bobić, Ilija and Stanković, Miloš and Hvizdoš, Pavol and Bobić, Biljana and Stojanović, Blaža and Franek, Friedrich",
year = "2020",
abstract = "Metal matrix composites are very inhomogeneous materials, and their properties depend on various parameters (production process, constituents, their interfaces, etc.). The influence of SiC microparticles (40 mu m) reinforcement and graphite macroparticles (200-800 mu m) addition on the mechanical properties of Al-Si A356 alloy, produced by compocasting, has been assessed using macro- and nanoscale measurements of hardness and modulus of elasticity. The Al makes over 90 wt% of the A356 alloy, so the nanoscale measurements were performed on different alpha phase regions on each material (core of alpha phase, eutectic alpha phase, and alpha phase near the phase boundaries alpha phase/secondary phases). The results showed that there is no direct correlation between mechanical properties on macro- and nanoscale. The nanoscale results also showed that the secondary phases (SiC and graphite particles) can have significant effect on the mechanical properties on the atomic level, i.e. in the alpha phase regions very close to the secondary phases.",
publisher = "Springer",
journal = "Journal of the Brazilian Society of Mechanical Sciences and Engineering",
title = "Influence of secondary phases in A356 MMCs on their mechanical properties at macro- and nanoscale",
volume = "42",
number = "3",
pages = "115",
doi = "10.1007/s40430-020-2197-6"
}

Vencl, A., Bobić, I., Stanković, M., Hvizdoš, P., Bobić, B., Stojanović, B.,& Franek, F.. (2020). Influence of secondary phases in A356 MMCs on their mechanical properties at macro- and nanoscale. in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Springer., 42(3), 115.
https://doi.org/10.1007/s40430-020-2197-6

Vencl A, Bobić I, Stanković M, Hvizdoš P, Bobić B, Stojanović B, Franek F. Influence of secondary phases in A356 MMCs on their mechanical properties at macro- and nanoscale. in Journal of the Brazilian Society of Mechanical Sciences and Engineering. 2020;42(3):115.
doi:10.1007/s40430-020-2197-6 .

Vencl, Aleksandar, Bobić, Ilija, Stanković, Miloš, Hvizdoš, Pavol, Bobić, Biljana, Stojanović, Blaža, Franek, Friedrich, "Influence of secondary phases in A356 MMCs on their mechanical properties at macro- and nanoscale" in Journal of the Brazilian Society of Mechanical Sciences and Engineering, 42, no. 3 (2020):115,
https://doi.org/10.1007/s40430-020-2197-6 . .

TY  - CONF
AU  - Mihailović, Marija
AU  - Radojković, Bojana M.
AU  - Daničić, Dunja
AU  - Kovačina, Jovanka
AU  - Stevanović, Jasmina
AU  - Bobić, Biljana
AU  - Jegdić, Bore
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/5438
AB  - The corrosion inhibiting possibility examination of extracts obtained from fruits of rose hip and
horse chestnut was investigated. Rose hip extracted at different temperatures exhibited different
corrosion inhibiting effect. Rose hip obtained at 40oC did not show any inhibiting effect in neutral
pH medium, while in acidic media it expressed moderate protective impact (up to 55%) for steel
and mild corrosion inhibiting impact for zinc (39%), while for aluminium and copper it did not
have any inhibiting effect. Rose hip obtained at 25oC exhibited significant inhibiting effect for steel
(up to 62 %) and even better for zinc (up to 72%) in neutral media. For aluminium and copper
neither of Rose hip extracts showed any inhibiting effect. The Horse chestnut extract exhibits
moderate to significant inhibiting effect for steel (up to 55%) and zinc (up to 60%) in neutral
media. In addition to this, because of the complex chemical composition of these fruit extracts,
some further electrochemical investigation is suggested, aimed to determine a single component
inhibitive effect. Firstly, as one of prevailing components, tannins are examined. Linear
polarization resistance (LPR) and electrochemical impedance spectroscopy (EIS) were used as a
testing techniques.
PB  - Belgrade, Serbia : Serbian Society of Corrosion and Materials Protection (Uiskozam)
C3  - Proceedings - XXI YUCORR International Conference
T1  - Green corrosion inhibitors
VL  - 21
SP  - 97
EP  - 105
UR  - https://hdl.handle.net/21.15107/rcub_cer_5438
ER  - 

@conference{
author = "Mihailović, Marija and Radojković, Bojana M. and Daničić, Dunja and Kovačina, Jovanka and Stevanović, Jasmina and Bobić, Biljana and Jegdić, Bore",
year = "2019",
abstract = "The corrosion inhibiting possibility examination of extracts obtained from fruits of rose hip and
horse chestnut was investigated. Rose hip extracted at different temperatures exhibited different
corrosion inhibiting effect. Rose hip obtained at 40oC did not show any inhibiting effect in neutral
pH medium, while in acidic media it expressed moderate protective impact (up to 55%) for steel
and mild corrosion inhibiting impact for zinc (39%), while for aluminium and copper it did not
have any inhibiting effect. Rose hip obtained at 25oC exhibited significant inhibiting effect for steel
(up to 62 %) and even better for zinc (up to 72%) in neutral media. For aluminium and copper
neither of Rose hip extracts showed any inhibiting effect. The Horse chestnut extract exhibits
moderate to significant inhibiting effect for steel (up to 55%) and zinc (up to 60%) in neutral
media. In addition to this, because of the complex chemical composition of these fruit extracts,
some further electrochemical investigation is suggested, aimed to determine a single component
inhibitive effect. Firstly, as one of prevailing components, tannins are examined. Linear
polarization resistance (LPR) and electrochemical impedance spectroscopy (EIS) were used as a
testing techniques.",
publisher = "Belgrade, Serbia : Serbian Society of Corrosion and Materials Protection (Uiskozam)",
journal = "Proceedings - XXI YUCORR International Conference",
title = "Green corrosion inhibitors",
volume = "21",
pages = "97-105",
url = "https://hdl.handle.net/21.15107/rcub_cer_5438"
}

Mihailović, M., Radojković, B. M., Daničić, D., Kovačina, J., Stevanović, J., Bobić, B.,& Jegdić, B.. (2019). Green corrosion inhibitors. in Proceedings - XXI YUCORR International Conference
Belgrade, Serbia : Serbian Society of Corrosion and Materials Protection (Uiskozam)., 21, 97-105.
https://hdl.handle.net/21.15107/rcub_cer_5438

Mihailović M, Radojković BM, Daničić D, Kovačina J, Stevanović J, Bobić B, Jegdić B. Green corrosion inhibitors. in Proceedings - XXI YUCORR International Conference. 2019;21:97-105.
https://hdl.handle.net/21.15107/rcub_cer_5438 .

Mihailović, Marija, Radojković, Bojana M., Daničić, Dunja, Kovačina, Jovanka, Stevanović, Jasmina, Bobić, Biljana, Jegdić, Bore, "Green corrosion inhibitors" in Proceedings - XXI YUCORR International Conference, 21 (2019):97-105,
https://hdl.handle.net/21.15107/rcub_cer_5438 .

TY  - CONF
AU  - Polić, Suzana R.
AU  - Ristić, Slavica
AU  - Radojković, Bojana M.
AU  - Jegdić, Bore
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/5439
AB  - In recent years, lasers have been used more and more in different areas of human life, science, industry, medicine, military, agriculture, and show business, protection of environmental and culturalheritage objects, in the arts and so on. Laser technology has some advantages in many areas over classical methods. This paper presents the results of laser application for cleaning corrosion of metal objects, cooper and brass. The first sample was oxidised cooper plate and the second ashtray made of brass. Nd: YAG laser was used as a source of radiation to clean surface corrosion deposits. Removal of layers from the surface occurs through the process of laser ablation. Three wavelengths were used with different fluences. The cleaning results, i.e. the morphological and chemical changes were investigated by optical microscopy, XRF analysis and colorimetry. The obtained results show that lasers are efficient corrosion cleaning and environmentally friendly method.
PB  - University of Belgrade, Technical Faculty in Bor
C3  - Proceedings 27th international conference Ecological truth and environmental research – EcoTER’19
T1  - Laser cleaning of corrosion, efficient and environmentally friendly method
VL  - 27
SP  - 362
EP  - 368
UR  - https://hdl.handle.net/21.15107/rcub_cer_5439
ER  - 

@conference{
author = "Polić, Suzana R. and Ristić, Slavica and Radojković, Bojana M. and Jegdić, Bore",
year = "2019",
abstract = "In recent years, lasers have been used more and more in different areas of human life, science, industry, medicine, military, agriculture, and show business, protection of environmental and culturalheritage objects, in the arts and so on. Laser technology has some advantages in many areas over classical methods. This paper presents the results of laser application for cleaning corrosion of metal objects, cooper and brass. The first sample was oxidised cooper plate and the second ashtray made of brass. Nd: YAG laser was used as a source of radiation to clean surface corrosion deposits. Removal of layers from the surface occurs through the process of laser ablation. Three wavelengths were used with different fluences. The cleaning results, i.e. the morphological and chemical changes were investigated by optical microscopy, XRF analysis and colorimetry. The obtained results show that lasers are efficient corrosion cleaning and environmentally friendly method.",
publisher = "University of Belgrade, Technical Faculty in Bor",
journal = "Proceedings 27th international conference Ecological truth and environmental research – EcoTER’19",
title = "Laser cleaning of corrosion, efficient and environmentally friendly method",
volume = "27",
pages = "362-368",
url = "https://hdl.handle.net/21.15107/rcub_cer_5439"
}

Polić, S. R., Ristić, S., Radojković, B. M.,& Jegdić, B.. (2019). Laser cleaning of corrosion, efficient and environmentally friendly method. in Proceedings 27th international conference Ecological truth and environmental research – EcoTER’19
University of Belgrade, Technical Faculty in Bor., 27, 362-368.
https://hdl.handle.net/21.15107/rcub_cer_5439

Polić SR, Ristić S, Radojković BM, Jegdić B. Laser cleaning of corrosion, efficient and environmentally friendly method. in Proceedings 27th international conference Ecological truth and environmental research – EcoTER’19. 2019;27:362-368.
https://hdl.handle.net/21.15107/rcub_cer_5439 .

Polić, Suzana R., Ristić, Slavica, Radojković, Bojana M., Jegdić, Bore, "Laser cleaning of corrosion, efficient and environmentally friendly method" in Proceedings 27th international conference Ecological truth and environmental research – EcoTER’19, 27 (2019):362-368,
https://hdl.handle.net/21.15107/rcub_cer_5439 .

TY  - CONF
AU  - Radojković, Bojana M.
AU  - Jegdić, Bore
AU  - Bobić, Biljana
AU  - Ristić, Slavica
AU  - Polić, Suzana R.
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/5434
AB  - Nd:YAG laser was used for cleaning surfaces of cultural heritage iron artefacts covered with corrosion products. The corrosion products were removed without damaging the base material. Three different electrochemical techniques were used for the determination of the corrosion rate of mechanically prepared iron, laser-cleaned iron and laser-cleaned iron with Paraloid B44 coating. The morphology of the tested surfaces was analysed by SEM. The linear polarization resistance technique, electrochemical impedance spectroscopy and linear sweep voltammetry have shown that the corrosion rate of the laser-cleaned iron is approximately 50 % higher than the corrosion rate of the mechanically prepared iron. Electrochemical impedance spectroscopy has shown that the pore resistance of the Paraloid coating on the laser-cleaned iron sample decreases at the beginning of the test and remains approximately constant after this period. At the beginning of the test, the charge transfer resistance value is constant and then decreases rapidly i.e. the corrosion rate of the iron in the Paraloid coating pores increases with time. During the linear sweep voltammetry test of the iron sample with Paraloid coating, it was noticed that the anodic polarisation curve shows an unusual shape at the potentials more positive than - 0.5 V.
PB  - The Serbian Society of Corrosion and Materials Protection
C3  - Proceedings - XXI YUCORR International Conference
T1  - Corrosion characteristics of laser-cleaned surfaces on the iron artefact
VL  - 21
SP  - 56
EP  - 69
UR  - https://hdl.handle.net/21.15107/rcub_cer_5434
ER  - 

@conference{
author = "Radojković, Bojana M. and Jegdić, Bore and Bobić, Biljana and Ristić, Slavica and Polić, Suzana R.",
year = "2019",
abstract = "Nd:YAG laser was used for cleaning surfaces of cultural heritage iron artefacts covered with corrosion products. The corrosion products were removed without damaging the base material. Three different electrochemical techniques were used for the determination of the corrosion rate of mechanically prepared iron, laser-cleaned iron and laser-cleaned iron with Paraloid B44 coating. The morphology of the tested surfaces was analysed by SEM. The linear polarization resistance technique, electrochemical impedance spectroscopy and linear sweep voltammetry have shown that the corrosion rate of the laser-cleaned iron is approximately 50 % higher than the corrosion rate of the mechanically prepared iron. Electrochemical impedance spectroscopy has shown that the pore resistance of the Paraloid coating on the laser-cleaned iron sample decreases at the beginning of the test and remains approximately constant after this period. At the beginning of the test, the charge transfer resistance value is constant and then decreases rapidly i.e. the corrosion rate of the iron in the Paraloid coating pores increases with time. During the linear sweep voltammetry test of the iron sample with Paraloid coating, it was noticed that the anodic polarisation curve shows an unusual shape at the potentials more positive than - 0.5 V.",
publisher = "The Serbian Society of Corrosion and Materials Protection",
journal = "Proceedings - XXI YUCORR International Conference",
title = "Corrosion characteristics of laser-cleaned surfaces on the iron artefact",
volume = "21",
pages = "56-69",
url = "https://hdl.handle.net/21.15107/rcub_cer_5434"
}

Radojković, B. M., Jegdić, B., Bobić, B., Ristić, S.,& Polić, S. R.. (2019). Corrosion characteristics of laser-cleaned surfaces on the iron artefact. in Proceedings - XXI YUCORR International Conference
The Serbian Society of Corrosion and Materials Protection., 21, 56-69.
https://hdl.handle.net/21.15107/rcub_cer_5434

Radojković BM, Jegdić B, Bobić B, Ristić S, Polić SR. Corrosion characteristics of laser-cleaned surfaces on the iron artefact. in Proceedings - XXI YUCORR International Conference. 2019;21:56-69.
https://hdl.handle.net/21.15107/rcub_cer_5434 .

Radojković, Bojana M., Jegdić, Bore, Bobić, Biljana, Ristić, Slavica, Polić, Suzana R., "Corrosion characteristics of laser-cleaned surfaces on the iron artefact" in Proceedings - XXI YUCORR International Conference, 21 (2019):56-69,
https://hdl.handle.net/21.15107/rcub_cer_5434 .

TY  - CHAP
AU  - Polić, Suzana R.
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/6167
AB  - Заштита нематеријалног културног наслеђа са аспекта херитологије још увек у
Србији не обухвата значајно наслеђе које датира од почетка српске музичке писменос-
ти, до данас. У раду се проблематизује питање херитолошког односа према знању које се
преноси усменим путем од ХIV века до данас, у оквиру литургијског осмогласног појања.
У фокусу истраживања је појање са базинеумских рукописa који се налазе ван Србије
у више универзитетских колекција и значајних манастирских библиотека. Управљање
знањем разматра се у специфичности канона у оквиру којег постоји поље импровизације
које произлази из праксе духовног обреда. Посебно се проблематизује могућност мулти-
дисциплинарног рада у примени дигитализације у заштити наслеђа.
AB  - Protection of the intangible cultural heritage, from the aspect of science of conservation
cultural heritage, still does not encompass significant heritage that has been dated
since the beginning of Serbian music literacy until today. The paper follows the heritologycal
point of view of the problemabout knowledge transmitted through the oral mode from the
14th century to today, within the liturgical church chant, with simultaniously interpretation
by eight – voices. The focus of the research is the poem based on the neume – old notation
manuscripts that are located outside Serbia in several university collections and significant
monastery libraries. Knowledge management is considered in the specificity of the canons in
which there is a field of improvisation that arises from the practice of spiritual ritual. Particularly,
in focus is the possibility of multidisciplinary work in the application of digitization
in the protection of heritage.
PB  - Српска академија наука и уметности / Serbian Academy of Sciences and Arts
PB  - Аудиовизуелни архив и центар за дигитализацију САНУ / Audiovisual Archive and Center for Digitalisation of SASA
PB  - Институт за упоредно право, Београд / Institute of Comparative Law, Belgrade
T2  - Примена дигитализације у култури и науци
T1  - Управљање знањем и нематеријално културно наслеђе
T1  - Management of knowledge and protection of an intangible cultural heritage
SP  - 137
EP  - 146
UR  - https://hdl.handle.net/21.15107/rcub_cer_6167
ER  - 

@inbook{
author = "Polić, Suzana R.",
year = "2019",
abstract = "Заштита нематеријалног културног наслеђа са аспекта херитологије још увек у
Србији не обухвата значајно наслеђе које датира од почетка српске музичке писменос-
ти, до данас. У раду се проблематизује питање херитолошког односа према знању које се
преноси усменим путем од ХIV века до данас, у оквиру литургијског осмогласног појања.
У фокусу истраживања је појање са базинеумских рукописa који се налазе ван Србије
у више универзитетских колекција и значајних манастирских библиотека. Управљање
знањем разматра се у специфичности канона у оквиру којег постоји поље импровизације
које произлази из праксе духовног обреда. Посебно се проблематизује могућност мулти-
дисциплинарног рада у примени дигитализације у заштити наслеђа., Protection of the intangible cultural heritage, from the aspect of science of conservation
cultural heritage, still does not encompass significant heritage that has been dated
since the beginning of Serbian music literacy until today. The paper follows the heritologycal
point of view of the problemabout knowledge transmitted through the oral mode from the
14th century to today, within the liturgical church chant, with simultaniously interpretation
by eight – voices. The focus of the research is the poem based on the neume – old notation
manuscripts that are located outside Serbia in several university collections and significant
monastery libraries. Knowledge management is considered in the specificity of the canons in
which there is a field of improvisation that arises from the practice of spiritual ritual. Particularly,
in focus is the possibility of multidisciplinary work in the application of digitization
in the protection of heritage.",
publisher = "Српска академија наука и уметности / Serbian Academy of Sciences and Arts, Аудиовизуелни архив и центар за дигитализацију САНУ / Audiovisual Archive and Center for Digitalisation of SASA, Институт за упоредно право, Београд / Institute of Comparative Law, Belgrade",
journal = "Примена дигитализације у култури и науци",
booktitle = "Управљање знањем и нематеријално културно наслеђе, Management of knowledge and protection of an intangible cultural heritage",
pages = "137-146",
url = "https://hdl.handle.net/21.15107/rcub_cer_6167"
}

Polić, S. R.. (2019). Управљање знањем и нематеријално културно наслеђе. in Примена дигитализације у култури и науци
Српска академија наука и уметности / Serbian Academy of Sciences and Arts., 137-146.
https://hdl.handle.net/21.15107/rcub_cer_6167

Polić SR. Управљање знањем и нематеријално културно наслеђе. in Примена дигитализације у култури и науци. 2019;:137-146.
https://hdl.handle.net/21.15107/rcub_cer_6167 .

Polić, Suzana R., "Управљање знањем и нематеријално културно наслеђе" in Примена дигитализације у култури и науци (2019):137-146,
https://hdl.handle.net/21.15107/rcub_cer_6167 .

TY  - CONF
AU  - Polić, Suzana R.
AU  - Petronić, Sanja
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/6369
AB  - Heritologija kao nauka o zaštiti kulturnog nasleđa, multidisciplinarna je oblast, u kojoj pitanje energije ima izuzetan značaj u domenu zaštite nepokretnog kulturnog nasleđa, odnosno arheoloških lokaliteta. Modeli savremene prezentacije nasleđa zasnovani su na primeni novih tehnologija, kao i na ekološkoj bezbednosti u koju je uključena i primena obnovljivih izvora energije. U ovom radu istražuju se metodološki problemi u formulisanju paradigme zasnovane na principima intentio operis i intentio auctoris, koja u projektovanju modela prezentacije kulturnog nasleđa uvažava pitanja jedinstvenosti, originalnosti i ekskluziviteta autorskih prostornih rešenja, zbog čega je veoma osetljivo i pitanje modela primene obnovljivih izvora energije.
AB  - Heritology, as a science for the protection of cultural heritage, is a multidisciplinary field in which the issue of energy is of great importance in terms of protection of immovable cultural herit-age, that is, archaeological sites. Models of contemporary heritage presentation are based on the application of new technologies, as well as on environmental safety, which includes the use of re-newable energy sources. This paper explores methodological problems of formulating a paradigm based on the principles of intentio operis and intentio auctoris, which in designing a model for the presentation of cultural heritage takes into account the uniqueness, originality and exclusivity of author's spatial solutions, which makes the model of renewable energy application very sensitive.
PB  - Beograd: Savez mašinskih i elektrotehičkih inženjera i tehničara Srbije (SMEITS) = Belgrade: Union of Mechanical and Electrical Engineers and Technicians of Serbia
C3  - Proceedings - 7th International Conference on Renewable Electrical Power Sources, October 17-18. 2019, Belgrade
T1  - Metodološki problemi primene obnovljivih izvora energije u zaštiti kulturnog nasleđa
T1  - Methodological problems of the application of renewable energy sources in cultural heritage protection
SP  - 265
EP  - 269
UR  - https://hdl.handle.net/21.15107/rcub_cer_6369
ER  - 

@conference{
author = "Polić, Suzana R. and Petronić, Sanja",
year = "2019",
abstract = "Heritologija kao nauka o zaštiti kulturnog nasleđa, multidisciplinarna je oblast, u kojoj pitanje energije ima izuzetan značaj u domenu zaštite nepokretnog kulturnog nasleđa, odnosno arheoloških lokaliteta. Modeli savremene prezentacije nasleđa zasnovani su na primeni novih tehnologija, kao i na ekološkoj bezbednosti u koju je uključena i primena obnovljivih izvora energije. U ovom radu istražuju se metodološki problemi u formulisanju paradigme zasnovane na principima intentio operis i intentio auctoris, koja u projektovanju modela prezentacije kulturnog nasleđa uvažava pitanja jedinstvenosti, originalnosti i ekskluziviteta autorskih prostornih rešenja, zbog čega je veoma osetljivo i pitanje modela primene obnovljivih izvora energije., Heritology, as a science for the protection of cultural heritage, is a multidisciplinary field in which the issue of energy is of great importance in terms of protection of immovable cultural herit-age, that is, archaeological sites. Models of contemporary heritage presentation are based on the application of new technologies, as well as on environmental safety, which includes the use of re-newable energy sources. This paper explores methodological problems of formulating a paradigm based on the principles of intentio operis and intentio auctoris, which in designing a model for the presentation of cultural heritage takes into account the uniqueness, originality and exclusivity of author's spatial solutions, which makes the model of renewable energy application very sensitive.",
publisher = "Beograd: Savez mašinskih i elektrotehičkih inženjera i tehničara Srbije (SMEITS) = Belgrade: Union of Mechanical and Electrical Engineers and Technicians of Serbia",
journal = "Proceedings - 7th International Conference on Renewable Electrical Power Sources, October 17-18. 2019, Belgrade",
title = "Metodološki problemi primene obnovljivih izvora energije u zaštiti kulturnog nasleđa, Methodological problems of the application of renewable energy sources in cultural heritage protection",
pages = "265-269",
url = "https://hdl.handle.net/21.15107/rcub_cer_6369"
}

Polić, S. R.,& Petronić, S.. (2019). Metodološki problemi primene obnovljivih izvora energije u zaštiti kulturnog nasleđa. in Proceedings - 7th International Conference on Renewable Electrical Power Sources, October 17-18. 2019, Belgrade
Beograd: Savez mašinskih i elektrotehičkih inženjera i tehničara Srbije (SMEITS) = Belgrade: Union of Mechanical and Electrical Engineers and Technicians of Serbia., 265-269.
https://hdl.handle.net/21.15107/rcub_cer_6369

Polić SR, Petronić S. Metodološki problemi primene obnovljivih izvora energije u zaštiti kulturnog nasleđa. in Proceedings - 7th International Conference on Renewable Electrical Power Sources, October 17-18. 2019, Belgrade. 2019;:265-269.
https://hdl.handle.net/21.15107/rcub_cer_6369 .

Polić, Suzana R., Petronić, Sanja, "Metodološki problemi primene obnovljivih izvora energije u zaštiti kulturnog nasleđa" in Proceedings - 7th International Conference on Renewable Electrical Power Sources, October 17-18. 2019, Belgrade (2019):265-269,
https://hdl.handle.net/21.15107/rcub_cer_6369 .

TY  - CONF
AU  - Petronić, Sanja
AU  - Polić, Suzana R.
AU  - Dragović, Magdalena
AU  - Srećković, Milesa
AU  - Milosavljević, Anđelka
PY  - 2019
UR  - https://www.izdanja.smeits.rs/index.php/mkoiee/article/view/5957
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/6391
AB  - Dokument o politici za integraciju perspektive održivog razvoja u Konvenciju o svetskoj baštini, koji je usvojila Generalna skupština država članica (UNESCO, 2015), ističe značaj primene obnovljivih izvora energije u oblasti zaštite kulturnog nasleđa. Komparativnom analizom naučnih rezultata u međunarodnoj praksi o primeni obnovljivih izvora energije u zaštiti baštine, u ovom radu istražuju se distinkcije značajne za formulisanje semantičkog plana primene obnovljivih izvora energije u zaštiti baštine, sa akcentima na parametrima ograničenosti i funkcionalnosti primene na značajnim objektima kulturnog nasleđa.
AB  - Policy document on the integration of a sustainable development perspective into the World Heritage Convention, adopted by the General Assembly of States Parties (UNESCO, 2015), empha-sizes the importance of implementing renewable sources of energy into the field of cultural heritage protection. Comparative analysis of scientific results in international practice on the application of renewable energy sources in heritage protection, in this paper explores the distinctions important for formulating a semantic plan for the application of renewable energy sources in heritage protec-tion, with emphasis on the parameters of limitations and functional applicability for significant cul-tural heritage objects.
PB  - Beograd: Savez mašinskih i elektrotehičkih inženjera i tehničara Srbije (SMEITS) = Belgrade:Union of Mechanical and Electrical Engineers and Technicians of Serbia
C3  - Proceedings - 7th International Conference on Renewable Electrical Power Sources, October 17-18. 2019, Belgrade / Zbornik Međunarodne konferencije o obnovljivim izvorima električne energije – MKOIEE
T1  - Distinkcije o obnovljivim izvorima energije  i zaštiti kulturnog nasleđa
T1  - Distinctions on renewable energy sources and cultural heritage protection
VL  - 7
IS  - 1
SP  - 257
EP  - 263
UR  - https://hdl.handle.net/21.15107/rcub_cer_6391
ER  - 

@conference{
author = "Petronić, Sanja and Polić, Suzana R. and Dragović, Magdalena and Srećković, Milesa and Milosavljević, Anđelka",
year = "2019",
abstract = "Dokument o politici za integraciju perspektive održivog razvoja u Konvenciju o svetskoj baštini, koji je usvojila Generalna skupština država članica (UNESCO, 2015), ističe značaj primene obnovljivih izvora energije u oblasti zaštite kulturnog nasleđa. Komparativnom analizom naučnih rezultata u međunarodnoj praksi o primeni obnovljivih izvora energije u zaštiti baštine, u ovom radu istražuju se distinkcije značajne za formulisanje semantičkog plana primene obnovljivih izvora energije u zaštiti baštine, sa akcentima na parametrima ograničenosti i funkcionalnosti primene na značajnim objektima kulturnog nasleđa., Policy document on the integration of a sustainable development perspective into the World Heritage Convention, adopted by the General Assembly of States Parties (UNESCO, 2015), empha-sizes the importance of implementing renewable sources of energy into the field of cultural heritage protection. Comparative analysis of scientific results in international practice on the application of renewable energy sources in heritage protection, in this paper explores the distinctions important for formulating a semantic plan for the application of renewable energy sources in heritage protec-tion, with emphasis on the parameters of limitations and functional applicability for significant cul-tural heritage objects.",
publisher = "Beograd: Savez mašinskih i elektrotehičkih inženjera i tehničara Srbije (SMEITS) = Belgrade:Union of Mechanical and Electrical Engineers and Technicians of Serbia",
journal = "Proceedings - 7th International Conference on Renewable Electrical Power Sources, October 17-18. 2019, Belgrade / Zbornik Međunarodne konferencije o obnovljivim izvorima električne energije – MKOIEE",
title = "Distinkcije o obnovljivim izvorima energije  i zaštiti kulturnog nasleđa, Distinctions on renewable energy sources and cultural heritage protection",
volume = "7",
number = "1",
pages = "257-263",
url = "https://hdl.handle.net/21.15107/rcub_cer_6391"
}

Petronić, S., Polić, S. R., Dragović, M., Srećković, M.,& Milosavljević, A.. (2019). Distinkcije o obnovljivim izvorima energije  i zaštiti kulturnog nasleđa. in Proceedings - 7th International Conference on Renewable Electrical Power Sources, October 17-18. 2019, Belgrade / Zbornik Međunarodne konferencije o obnovljivim izvorima električne energije – MKOIEE
Beograd: Savez mašinskih i elektrotehičkih inženjera i tehničara Srbije (SMEITS) = Belgrade:Union of Mechanical and Electrical Engineers and Technicians of Serbia., 7(1), 257-263.
https://hdl.handle.net/21.15107/rcub_cer_6391

Petronić S, Polić SR, Dragović M, Srećković M, Milosavljević A. Distinkcije o obnovljivim izvorima energije  i zaštiti kulturnog nasleđa. in Proceedings - 7th International Conference on Renewable Electrical Power Sources, October 17-18. 2019, Belgrade / Zbornik Međunarodne konferencije o obnovljivim izvorima električne energije – MKOIEE. 2019;7(1):257-263.
https://hdl.handle.net/21.15107/rcub_cer_6391 .

Petronić, Sanja, Polić, Suzana R., Dragović, Magdalena, Srećković, Milesa, Milosavljević, Anđelka, "Distinkcije o obnovljivim izvorima energije  i zaštiti kulturnog nasleđa" in Proceedings - 7th International Conference on Renewable Electrical Power Sources, October 17-18. 2019, Belgrade / Zbornik Međunarodne konferencije o obnovljivim izvorima električne energije – MKOIEE, 7, no. 1 (2019):257-263,
https://hdl.handle.net/21.15107/rcub_cer_6391 .

TY  - CONF
AU  - Polić, Suzana R.
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/6178
AB  - New technologies are making significant progress in protecting cultural heritage and their application in this area has become an imperative of multidisciplinary connection in many fields such as: art, culture, history, archeology, sustainable development, environmental technology, problems of management issues in innovation, technology of materials, as well as numerous secondary disciplines. Managing projects that cover heritage protection is all the more complex when contemporary problems are more diverse, and this also requires the involvement of more experts and researchers with very different experience. This paper presents methodologies in composition of human resources in the goals to multidisciplinary research of conservation and restoration of art and archaeology artifacts. Observing potentials of different researchers we indirectly conclude about qualitative parameters of education necessary to work in application new technology in the field of cultural heritage protection. Our investigation results lead to some conclusions:  it has been concluded that theoretical basis and understanding of heuristic views to problems of degradation of cultural heritage are both important. Equally important is continuous education and its implication in using new technologies in cultural heritage protection.
PB  - European International Research Academy (EIRA)
C3  - Proceeding EBES-2019
T1  - Technology education and human resources in the multidisciplinary processes of cultural heritage protection
SP  - 14
EP  - 14
UR  - https://hdl.handle.net/21.15107/rcub_cer_6178
ER  - 

@conference{
author = "Polić, Suzana R.",
year = "2019",
abstract = "New technologies are making significant progress in protecting cultural heritage and their application in this area has become an imperative of multidisciplinary connection in many fields such as: art, culture, history, archeology, sustainable development, environmental technology, problems of management issues in innovation, technology of materials, as well as numerous secondary disciplines. Managing projects that cover heritage protection is all the more complex when contemporary problems are more diverse, and this also requires the involvement of more experts and researchers with very different experience. This paper presents methodologies in composition of human resources in the goals to multidisciplinary research of conservation and restoration of art and archaeology artifacts. Observing potentials of different researchers we indirectly conclude about qualitative parameters of education necessary to work in application new technology in the field of cultural heritage protection. Our investigation results lead to some conclusions:  it has been concluded that theoretical basis and understanding of heuristic views to problems of degradation of cultural heritage are both important. Equally important is continuous education and its implication in using new technologies in cultural heritage protection.",
publisher = "European International Research Academy (EIRA)",
journal = "Proceeding EBES-2019",
title = "Technology education and human resources in the multidisciplinary processes of cultural heritage protection",
pages = "14-14",
url = "https://hdl.handle.net/21.15107/rcub_cer_6178"
}

Polić, S. R.. (2019). Technology education and human resources in the multidisciplinary processes of cultural heritage protection. in Proceeding EBES-2019
European International Research Academy (EIRA)., 14-14.
https://hdl.handle.net/21.15107/rcub_cer_6178

Polić SR. Technology education and human resources in the multidisciplinary processes of cultural heritage protection. in Proceeding EBES-2019. 2019;:14-14.
https://hdl.handle.net/21.15107/rcub_cer_6178 .

Polić, Suzana R., "Technology education and human resources in the multidisciplinary processes of cultural heritage protection" in Proceeding EBES-2019 (2019):14-14,
https://hdl.handle.net/21.15107/rcub_cer_6178 .

TY  - CHAP
AU  - Polić, Suzana R.
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/6058
AB  - In 2017, the Parliament of Europe adopted the proposal to draft
the legislation on the protection of the rights of electronic persons,
or of the person of a humanoid robot. This legal introduction into
the robot technological revolution, the first one, which will not be
carried out by man, presses for the religious and technological
concepts of person to be examined in parallel. Starting from the
humanistic attitudes of Dostoyevsky, Žarko Vidović, as well as of
father Metrophanes, on one hand, and from the abuse of techno-
logical research based on the methods of biomimicry and artificial
intelligence, on the other, the paper observes Dictionary of Tech-
nology. It brought the notion of selfhood into focus, anticipated and
warned against the events that would follow through three techno-
logical revolutions, which may all, in their own way, be understood
as the reduction of a live person down to an electronic one.
PB  - National Hellenic Research Foundation
PB  - Institute of Historical Research
T2  - Orthodoxy and  artificial intelligence -  Dictionary of Technology  and a Double Logos:  A Contribution to the Dialogue  of Science and Religion
T1  - Dictionary of Technology and Electronic Personality
SP  - 61
EP  - 79
UR  - https://hdl.handle.net/21.15107/rcub_cer_6058
ER  - 

@inbook{
author = "Polić, Suzana R.",
year = "2019",
abstract = "In 2017, the Parliament of Europe adopted the proposal to draft
the legislation on the protection of the rights of electronic persons,
or of the person of a humanoid robot. This legal introduction into
the robot technological revolution, the first one, which will not be
carried out by man, presses for the religious and technological
concepts of person to be examined in parallel. Starting from the
humanistic attitudes of Dostoyevsky, Žarko Vidović, as well as of
father Metrophanes, on one hand, and from the abuse of techno-
logical research based on the methods of biomimicry and artificial
intelligence, on the other, the paper observes Dictionary of Tech-
nology. It brought the notion of selfhood into focus, anticipated and
warned against the events that would follow through three techno-
logical revolutions, which may all, in their own way, be understood
as the reduction of a live person down to an electronic one.",
publisher = "National Hellenic Research Foundation, Institute of Historical Research",
journal = "Orthodoxy and  artificial intelligence -  Dictionary of Technology  and a Double Logos:  A Contribution to the Dialogue  of Science and Religion",
booktitle = "Dictionary of Technology and Electronic Personality",
pages = "61-79",
url = "https://hdl.handle.net/21.15107/rcub_cer_6058"
}

Polić, S. R.. (2019). Dictionary of Technology and Electronic Personality. in Orthodoxy and  artificial intelligence -  Dictionary of Technology  and a Double Logos:  A Contribution to the Dialogue  of Science and Religion
National Hellenic Research Foundation., 61-79.
https://hdl.handle.net/21.15107/rcub_cer_6058

Polić SR. Dictionary of Technology and Electronic Personality. in Orthodoxy and  artificial intelligence -  Dictionary of Technology  and a Double Logos:  A Contribution to the Dialogue  of Science and Religion. 2019;:61-79.
https://hdl.handle.net/21.15107/rcub_cer_6058 .

Polić, Suzana R., "Dictionary of Technology and Electronic Personality" in Orthodoxy and  artificial intelligence -  Dictionary of Technology  and a Double Logos:  A Contribution to the Dialogue  of Science and Religion (2019):61-79,
https://hdl.handle.net/21.15107/rcub_cer_6058 .

TY  - JOUR
AU  - Ristić, Slavica R.
AU  - Polić, Suzana R.
AU  - Knježević, Dragan M.
AU  - Radojković, Bojana
AU  - Linić, Suzana
AU  - Jegdić, Bore
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3453
AB  - Inovativna tehnologija laserskog čišćenja različitih površina u industriji, uključuje integrisani pristup kontrole procesa interakcije laser-materijal i ispitivanja rezultata laserskog delovanja. Lasersko čišćenje ima značajne prednosti u odnosu na klasične metode čišćenja: ima veliku selektivnost, preciznost, efikasnost i pouzdanost u primeni kod različitih vrsta materijala. Termalna priroda procesa laserskog čišćenja unosi određeni rizik po predmete čišćenja, te su istraživanja optimizacije procesa u fokusu interesovanja velikog broja naučnika. U radu su prikazani rezultati laserskog čišćenja boje na bakarnoj površini i zaštitnog sloja na štampanoj pločici. Kontrola procesa laserskog čišćenja u realnom vremenu je vršena pomoću infracrvene kamere. Mikromorfološke promene čišćene površine su ispitivani optičkom mikroskopijom.
AB  - Innovative laser cleaning technology for various surfaces in the industry, includes an integrated
approach to controlling the process of laser-material interaction and testing laser treatment results.
Laser cleaning has significant advantages over conventional cleaning methods: it has high selectivity,
precision, efficiency and reliability in an application for different types of materials. The thermal nature
of the laser cleaning process brings a certain risk for cleaning objects, and the process optimization
research is in the focus of interest of a large number of scientists. This paper presents the results of laser
paint, on the copper surface, and the protective layer, on the printed circuit board, cleaning. The control
of the real-time laser cleaning process was carried out using an infrared camera. The
micromorphological characteristics of the cleaned surface were examined by optical microscopy
PB  - Beograd : Savez inženjera i tehničara Srbije
T2  - Tehnika
T1  - Termografija u kontroli efikasnosti i bezbednosti laserskog čišćenja
T1  - Thermography in control efficiency and safety of laser cleaning
VL  - 74
IS  - 5
SP  - 623
EP  - 629
DO  - 10.5937/tehnika1905623R
ER  - 

@article{
author = "Ristić, Slavica R. and Polić, Suzana R. and Knježević, Dragan M. and Radojković, Bojana and Linić, Suzana and Jegdić, Bore",
year = "2019",
abstract = "Inovativna tehnologija laserskog čišćenja različitih površina u industriji, uključuje integrisani pristup kontrole procesa interakcije laser-materijal i ispitivanja rezultata laserskog delovanja. Lasersko čišćenje ima značajne prednosti u odnosu na klasične metode čišćenja: ima veliku selektivnost, preciznost, efikasnost i pouzdanost u primeni kod različitih vrsta materijala. Termalna priroda procesa laserskog čišćenja unosi određeni rizik po predmete čišćenja, te su istraživanja optimizacije procesa u fokusu interesovanja velikog broja naučnika. U radu su prikazani rezultati laserskog čišćenja boje na bakarnoj površini i zaštitnog sloja na štampanoj pločici. Kontrola procesa laserskog čišćenja u realnom vremenu je vršena pomoću infracrvene kamere. Mikromorfološke promene čišćene površine su ispitivani optičkom mikroskopijom., Innovative laser cleaning technology for various surfaces in the industry, includes an integrated
approach to controlling the process of laser-material interaction and testing laser treatment results.
Laser cleaning has significant advantages over conventional cleaning methods: it has high selectivity,
precision, efficiency and reliability in an application for different types of materials. The thermal nature
of the laser cleaning process brings a certain risk for cleaning objects, and the process optimization
research is in the focus of interest of a large number of scientists. This paper presents the results of laser
paint, on the copper surface, and the protective layer, on the printed circuit board, cleaning. The control
of the real-time laser cleaning process was carried out using an infrared camera. The
micromorphological characteristics of the cleaned surface were examined by optical microscopy",
publisher = "Beograd : Savez inženjera i tehničara Srbije",
journal = "Tehnika",
title = "Termografija u kontroli efikasnosti i bezbednosti laserskog čišćenja, Thermography in control efficiency and safety of laser cleaning",
volume = "74",
number = "5",
pages = "623-629",
doi = "10.5937/tehnika1905623R"
}

Ristić, S. R., Polić, S. R., Knježević, D. M., Radojković, B., Linić, S.,& Jegdić, B.. (2019). Termografija u kontroli efikasnosti i bezbednosti laserskog čišćenja. in Tehnika
Beograd : Savez inženjera i tehničara Srbije., 74(5), 623-629.
https://doi.org/10.5937/tehnika1905623R

Ristić SR, Polić SR, Knježević DM, Radojković B, Linić S, Jegdić B. Termografija u kontroli efikasnosti i bezbednosti laserskog čišćenja. in Tehnika. 2019;74(5):623-629.
doi:10.5937/tehnika1905623R .

Ristić, Slavica R., Polić, Suzana R., Knježević, Dragan M., Radojković, Bojana, Linić, Suzana, Jegdić, Bore, "Termografija u kontroli efikasnosti i bezbednosti laserskog čišćenja" in Tehnika, 74, no. 5 (2019):623-629,
https://doi.org/10.5937/tehnika1905623R . .

TY  - CONF
AU  - Kovačina, Jovanka
AU  - Milošević, Milena D.
AU  - Božić, Aleksandra
AU  - Jovanović, Aleksandar
AU  - Marinković, Aleksandar D.
AU  - Onjia, Antonije E.
AU  - Povrenović, Dragan
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3939
AB  - Usled razvoja industrije i rastom populacije tokom poslednjih godina javljaju se
problemi u vezi sa otpadnim vodama iz proizvodnje koje je neophodno rešavati na ekološki i
ekonomičan način. Sve otpadne vode iz postrojenja bez obzira kako su nastale sadrže štetne
materije koje mogu da imaju i određen stepen toksičnih primesa, moraju se prečistiti ako njihov
kvalitet ne odgovara zakonskim okvirima. Svrha tretmana otpadnih voda je uklanjanje štetnih
materija čime se postiže smanjnje stepena njene zagađenosti, a istovremeno se ostvaruje i određen
ekonomski i ekološki efekat, stoga je u ovom radu izvršeno prečišćavanje otpadne vode postupkom
taloženja upotrebom kalcijum-oksida u cilju uklanjanja koloidnih materija i teških metala. Većina
zagađujućih materija su organskog porekla i njihovo ukljanjanje vršiće se primenom naprednih
oksidacionih procesa korišćenjem ozona i ozona u kombinaciji sa ultrazvukom u cilju postizanja
kvaliteta vode koji odgovara zakonskoj regulativi. Proces prečišćavanja će se optimizovati u
odnosu na tehnološki postupak, koncentraciju, vreme tretmana i količinu primenjenog oksidacionog
sredstva. Stepen zagađenosti vode organskim jedinjenjima će se određivati na osnovu merenja
HPK, BPK i koncentracije teških metala (olovo, gvožđe, hrom, bakar, cink, aluminijum).
AB  - Due to the development of industry and population growth during the in recent years, there are problems with wastewater from production that needs to be addressed in an environmentally and economical way. All wastewaters from industry, no matter how they are created, contain harmful substances that may have some degree of toxicity, must be treated if their quality does not meet the legal requirements. The purpose of wastewater treatment is to remove
harmful substances, thereby reducing its pollution level, and at the same time, it also has a certain economic and environmental effect. Therefore, wastewater treatment was carried out in this work by precipitation using calcium oxide to remove colloidal substances and heavy metals. Most pollutants are of organic origin and their removal will be carried in this work out using advanced
oxidation processes using ozone, and ozone in combination with ultrasound to achieve water quality that complies with the law. The purification process will be optimized with respect to, method, time and amount of oxidizing agent applied. The degree of pollution of water by organic compounds will be determined on the basis of measurements of HPK, BOD and the concentration of heavy metals (lead, ferrum, chromium, copper, zinc, aluminum).
PB  - Beograd : Beogradska politehnika
C3  - Zbornik radova - Peti naučno-stručni skup politehnika
T1  - Prečišćavanje otpadnih voda primenom ozonizacije
T1  - Purification of waste water using ozonization
SP  - 142
EP  - 147
UR  - https://hdl.handle.net/21.15107/rcub_cer_3939
ER  - 

@conference{
author = "Kovačina, Jovanka and Milošević, Milena D. and Božić, Aleksandra and Jovanović, Aleksandar and Marinković, Aleksandar D. and Onjia, Antonije E. and Povrenović, Dragan",
year = "2019",
abstract = "Usled razvoja industrije i rastom populacije tokom poslednjih godina javljaju se
problemi u vezi sa otpadnim vodama iz proizvodnje koje je neophodno rešavati na ekološki i
ekonomičan način. Sve otpadne vode iz postrojenja bez obzira kako su nastale sadrže štetne
materije koje mogu da imaju i određen stepen toksičnih primesa, moraju se prečistiti ako njihov
kvalitet ne odgovara zakonskim okvirima. Svrha tretmana otpadnih voda je uklanjanje štetnih
materija čime se postiže smanjnje stepena njene zagađenosti, a istovremeno se ostvaruje i određen
ekonomski i ekološki efekat, stoga je u ovom radu izvršeno prečišćavanje otpadne vode postupkom
taloženja upotrebom kalcijum-oksida u cilju uklanjanja koloidnih materija i teških metala. Većina
zagađujućih materija su organskog porekla i njihovo ukljanjanje vršiće se primenom naprednih
oksidacionih procesa korišćenjem ozona i ozona u kombinaciji sa ultrazvukom u cilju postizanja
kvaliteta vode koji odgovara zakonskoj regulativi. Proces prečišćavanja će se optimizovati u
odnosu na tehnološki postupak, koncentraciju, vreme tretmana i količinu primenjenog oksidacionog
sredstva. Stepen zagađenosti vode organskim jedinjenjima će se određivati na osnovu merenja
HPK, BPK i koncentracije teških metala (olovo, gvožđe, hrom, bakar, cink, aluminijum)., Due to the development of industry and population growth during the in recent years, there are problems with wastewater from production that needs to be addressed in an environmentally and economical way. All wastewaters from industry, no matter how they are created, contain harmful substances that may have some degree of toxicity, must be treated if their quality does not meet the legal requirements. The purpose of wastewater treatment is to remove
harmful substances, thereby reducing its pollution level, and at the same time, it also has a certain economic and environmental effect. Therefore, wastewater treatment was carried out in this work by precipitation using calcium oxide to remove colloidal substances and heavy metals. Most pollutants are of organic origin and their removal will be carried in this work out using advanced
oxidation processes using ozone, and ozone in combination with ultrasound to achieve water quality that complies with the law. The purification process will be optimized with respect to, method, time and amount of oxidizing agent applied. The degree of pollution of water by organic compounds will be determined on the basis of measurements of HPK, BOD and the concentration of heavy metals (lead, ferrum, chromium, copper, zinc, aluminum).",
publisher = "Beograd : Beogradska politehnika",
journal = "Zbornik radova - Peti naučno-stručni skup politehnika",
title = "Prečišćavanje otpadnih voda primenom ozonizacije, Purification of waste water using ozonization",
pages = "142-147",
url = "https://hdl.handle.net/21.15107/rcub_cer_3939"
}

Kovačina, J., Milošević, M. D., Božić, A., Jovanović, A., Marinković, A. D., Onjia, A. E.,& Povrenović, D.. (2019). Prečišćavanje otpadnih voda primenom ozonizacije. in Zbornik radova - Peti naučno-stručni skup politehnika
Beograd : Beogradska politehnika., 142-147.
https://hdl.handle.net/21.15107/rcub_cer_3939

Kovačina J, Milošević MD, Božić A, Jovanović A, Marinković AD, Onjia AE, Povrenović D. Prečišćavanje otpadnih voda primenom ozonizacije. in Zbornik radova - Peti naučno-stručni skup politehnika. 2019;:142-147.
https://hdl.handle.net/21.15107/rcub_cer_3939 .

Kovačina, Jovanka, Milošević, Milena D., Božić, Aleksandra, Jovanović, Aleksandar, Marinković, Aleksandar D., Onjia, Antonije E., Povrenović, Dragan, "Prečišćavanje otpadnih voda primenom ozonizacije" in Zbornik radova - Peti naučno-stručni skup politehnika (2019):142-147,
https://hdl.handle.net/21.15107/rcub_cer_3939 .

TY  - JOUR
AU  - Milošević, Milena D.
AU  - Daničić, Dunja
AU  - Kovačina, Jovanka
AU  - Bugarčić, Mladen
AU  - Rusmirović, Jelena
AU  - Kovačević, Tihomir M.
AU  - Marinković, Aleksandar D.
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3461
AB  - The study of the synthesis of anticorrosive inhibitors, based on chemically modified tannins, and
their use in alkyd based coatings to improve anticorrosive properties is presented in this work.
Two methods of tannin modification were applied: direct method using ammonium hydroxide,
ammonium hydroxide/ammonium chloride buffer or diethylenetriamine (DETA); and a two-step
method including tannin modification with epichlorohydrin (ECH) in first step to produce epoxy
modified tannin, ET, and further modification with heteroaromatic amines or linseed oil fatty acids
(LFA) in second step. The obtained anticorrosive additives were characterized using ATR-FTIR,
1H and 13C NMR spectroscopies and elemental analysis. Epoxy, amino, hydroxyl, acid and iodine
values of the synthesized inhibitors were determined according to standard methods. The
prepared alkyd coating with tannin inhibitors was tested according to standard SRPS EN ISO
4628 method. Anticorrosive coating containing modified tannin based additive showed increased
anticorrosive properties, good adhesion and coverage comparing to the coating with zinc
phosphate additive. The alkyd coating films based on ET-LFA and ET modified with 2-amino-5-
mercapto-1,3,4-thiadiazole showed best anticorrosive results.
AB  - U ovom radu prikazana je sinteza antikorozionih aditiva na bazi hemijski modifikovanog tanina i njihova primena u alkidnim premazima u cilju poboljšanja antikorozionih svojstava. Prikazane su dve metode modifikacije tanina: direktna modifikacija tanina primenom amonijum-hidroksida, amonijum-hidroksid/amonijum-hlorid pufera ili dietilentriamina (DETA); i dvostepena modifikacija tanina koja u prvom stupnju uključuje modifikaciju epihlorhidrinom sa ciljem da se dobije tannin sa epoksi terminiranim funkcionalnim grupama, ET, i modifikaciju ET tanina sa heteroaromatičnim aminima ili masnim kiselinama izolovanim iz lanenog ulja (LFA) u drugom stupnju. Sintetisani antikorozioni aditivi su okarakterisani primenom ATR-FTIR, 1H i 13C NMR spektroskopija, i elementalnom analizom. Sadržaj epoksi, amino, hidroksilnih i karboksilnih grupa i vrednost jodnog broja sintetisanih aditiva određen je prema standardnim metodama. Alkidni premazi koji sadrže antikorozione aditive na bazi modifikovanog tanina ispitani su prema standardnoj SRPS EN ISO 4628 metodi. Antikorozivni alkidni premazi na bazi modfikovanih tanina pokazali su poboljšane antikorozione karakteristike i adheziju u poređenju sa alkidnim premazom na bazi cink-fosfata. Alkidni premazi koji sadrže dvostepeno modifikovani tanin sa LFA i 2-amino-5-merkapto-1,3,4-tiadiazolom pokazali su najbolje antikorozione karakteristike.
PB  - Belgrade : Engineering Society for Corrosion
T2  - Zastita materijala
T1  - Modified tannins for alkyd based anticorrosive coatings
T1  - Primena modifikovanih tanina u antikorozionim alkidnim premazima
VL  - 60
IS  - 1
SP  - 81
EP  - 95
DO  - 10.5937/zasmat1901081M
ER  - 

@article{
author = "Milošević, Milena D. and Daničić, Dunja and Kovačina, Jovanka and Bugarčić, Mladen and Rusmirović, Jelena and Kovačević, Tihomir M. and Marinković, Aleksandar D.",
year = "2019",
abstract = "The study of the synthesis of anticorrosive inhibitors, based on chemically modified tannins, and
their use in alkyd based coatings to improve anticorrosive properties is presented in this work.
Two methods of tannin modification were applied: direct method using ammonium hydroxide,
ammonium hydroxide/ammonium chloride buffer or diethylenetriamine (DETA); and a two-step
method including tannin modification with epichlorohydrin (ECH) in first step to produce epoxy
modified tannin, ET, and further modification with heteroaromatic amines or linseed oil fatty acids
(LFA) in second step. The obtained anticorrosive additives were characterized using ATR-FTIR,
1H and 13C NMR spectroscopies and elemental analysis. Epoxy, amino, hydroxyl, acid and iodine
values of the synthesized inhibitors were determined according to standard methods. The
prepared alkyd coating with tannin inhibitors was tested according to standard SRPS EN ISO
4628 method. Anticorrosive coating containing modified tannin based additive showed increased
anticorrosive properties, good adhesion and coverage comparing to the coating with zinc
phosphate additive. The alkyd coating films based on ET-LFA and ET modified with 2-amino-5-
mercapto-1,3,4-thiadiazole showed best anticorrosive results., U ovom radu prikazana je sinteza antikorozionih aditiva na bazi hemijski modifikovanog tanina i njihova primena u alkidnim premazima u cilju poboljšanja antikorozionih svojstava. Prikazane su dve metode modifikacije tanina: direktna modifikacija tanina primenom amonijum-hidroksida, amonijum-hidroksid/amonijum-hlorid pufera ili dietilentriamina (DETA); i dvostepena modifikacija tanina koja u prvom stupnju uključuje modifikaciju epihlorhidrinom sa ciljem da se dobije tannin sa epoksi terminiranim funkcionalnim grupama, ET, i modifikaciju ET tanina sa heteroaromatičnim aminima ili masnim kiselinama izolovanim iz lanenog ulja (LFA) u drugom stupnju. Sintetisani antikorozioni aditivi su okarakterisani primenom ATR-FTIR, 1H i 13C NMR spektroskopija, i elementalnom analizom. Sadržaj epoksi, amino, hidroksilnih i karboksilnih grupa i vrednost jodnog broja sintetisanih aditiva određen je prema standardnim metodama. Alkidni premazi koji sadrže antikorozione aditive na bazi modifikovanog tanina ispitani su prema standardnoj SRPS EN ISO 4628 metodi. Antikorozivni alkidni premazi na bazi modfikovanih tanina pokazali su poboljšane antikorozione karakteristike i adheziju u poređenju sa alkidnim premazom na bazi cink-fosfata. Alkidni premazi koji sadrže dvostepeno modifikovani tanin sa LFA i 2-amino-5-merkapto-1,3,4-tiadiazolom pokazali su najbolje antikorozione karakteristike.",
publisher = "Belgrade : Engineering Society for Corrosion",
journal = "Zastita materijala",
title = "Modified tannins for alkyd based anticorrosive coatings, Primena modifikovanih tanina u antikorozionim alkidnim premazima",
volume = "60",
number = "1",
pages = "81-95",
doi = "10.5937/zasmat1901081M"
}

Milošević, M. D., Daničić, D., Kovačina, J., Bugarčić, M., Rusmirović, J., Kovačević, T. M.,& Marinković, A. D.. (2019). Modified tannins for alkyd based anticorrosive coatings. in Zastita materijala
Belgrade : Engineering Society for Corrosion., 60(1), 81-95.
https://doi.org/10.5937/zasmat1901081M

Milošević MD, Daničić D, Kovačina J, Bugarčić M, Rusmirović J, Kovačević TM, Marinković AD. Modified tannins for alkyd based anticorrosive coatings. in Zastita materijala. 2019;60(1):81-95.
doi:10.5937/zasmat1901081M .

Milošević, Milena D., Daničić, Dunja, Kovačina, Jovanka, Bugarčić, Mladen, Rusmirović, Jelena, Kovačević, Tihomir M., Marinković, Aleksandar D., "Modified tannins for alkyd based anticorrosive coatings" in Zastita materijala, 60, no. 1 (2019):81-95,
https://doi.org/10.5937/zasmat1901081M . .

TY  - CONF
AU  - Kojić, Jovan D.
AU  - Kovačina, Jovanka
AU  - Milošević, Milena D.
AU  - Marinković, Aleksandar D.
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/6865
AB  - Heterocyclic furan-based compounds are interesting bio-renewable materials used as intermediate for pharmaceuticals, biodegradable resins, biofuels and fine chemicals syntheses. Additionally, HMF also functions as an anti-sickling agent for intermolecular sickle hemoglobin without inhibition by plasma and tissue proteins or other undesirable sequences.
T1  - Optimization of Microwave-Assisted synthesis of 5-hydroxymethyl-2-furfural
UR  - https://hdl.handle.net/21.15107/rcub_cer_6865
ER  - 

@conference{
author = "Kojić, Jovan D. and Kovačina, Jovanka and Milošević, Milena D. and Marinković, Aleksandar D.",
year = "2019",
abstract = "Heterocyclic furan-based compounds are interesting bio-renewable materials used as intermediate for pharmaceuticals, biodegradable resins, biofuels and fine chemicals syntheses. Additionally, HMF also functions as an anti-sickling agent for intermolecular sickle hemoglobin without inhibition by plasma and tissue proteins or other undesirable sequences.",
title = "Optimization of Microwave-Assisted synthesis of 5-hydroxymethyl-2-furfural",
url = "https://hdl.handle.net/21.15107/rcub_cer_6865"
}

Kojić, J. D., Kovačina, J., Milošević, M. D.,& Marinković, A. D.. (2019). Optimization of Microwave-Assisted synthesis of 5-hydroxymethyl-2-furfural. .
https://hdl.handle.net/21.15107/rcub_cer_6865

Kojić JD, Kovačina J, Milošević MD, Marinković AD. Optimization of Microwave-Assisted synthesis of 5-hydroxymethyl-2-furfural. 2019;.
https://hdl.handle.net/21.15107/rcub_cer_6865 .

Kojić, Jovan D., Kovačina, Jovanka, Milošević, Milena D., Marinković, Aleksandar D., "Optimization of Microwave-Assisted synthesis of 5-hydroxymethyl-2-furfural" (2019),
https://hdl.handle.net/21.15107/rcub_cer_6865 .

TY  - CONF
AU  - Kovačina, Jovanka
AU  - Kojić, Jovan D.
AU  - Milošević, Milena D.
AU  - Marinković, Aleksandar D.
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/6866
AB  - Levulinic acid (4-oxopentanoic acid) (LA) is a two-functional γ-keto acid widely used in a production of pharmaceuticals, ethyl levulinate, the substance which is
widely used in the cream and perfume industry, polymers, plasticizers, biofuel, resins, and various other additives.
LA was synthesized by the dehydration of fructose in a strongly acidic aqueous medium, using diluted hydrochloric acid, and subjected to microwave irradiation at
different operational conditions. LA was further used in two subsequent steps of peroxidation and dehydration to obtain 3-hydroxypropanoic acid and maleic
anhydride (MA) and acrylic acid (AA), respectively, which could be used for acrylic ester synthesis which could be used as a monomer in a polyacrylate
production (Figure 1).
T1  - Microwave-Assisted of synthesis and characterizations of levulinic acid (LA)
UR  - https://hdl.handle.net/21.15107/rcub_cer_6866
ER  - 

@conference{
author = "Kovačina, Jovanka and Kojić, Jovan D. and Milošević, Milena D. and Marinković, Aleksandar D.",
year = "2019",
abstract = "Levulinic acid (4-oxopentanoic acid) (LA) is a two-functional γ-keto acid widely used in a production of pharmaceuticals, ethyl levulinate, the substance which is
widely used in the cream and perfume industry, polymers, plasticizers, biofuel, resins, and various other additives.
LA was synthesized by the dehydration of fructose in a strongly acidic aqueous medium, using diluted hydrochloric acid, and subjected to microwave irradiation at
different operational conditions. LA was further used in two subsequent steps of peroxidation and dehydration to obtain 3-hydroxypropanoic acid and maleic
anhydride (MA) and acrylic acid (AA), respectively, which could be used for acrylic ester synthesis which could be used as a monomer in a polyacrylate
production (Figure 1).",
title = "Microwave-Assisted of synthesis and characterizations of levulinic acid (LA)",
url = "https://hdl.handle.net/21.15107/rcub_cer_6866"
}

Kovačina, J., Kojić, J. D., Milošević, M. D.,& Marinković, A. D.. (2019). Microwave-Assisted of synthesis and characterizations of levulinic acid (LA). .
https://hdl.handle.net/21.15107/rcub_cer_6866

Kovačina J, Kojić JD, Milošević MD, Marinković AD. Microwave-Assisted of synthesis and characterizations of levulinic acid (LA). 2019;.
https://hdl.handle.net/21.15107/rcub_cer_6866 .

Kovačina, Jovanka, Kojić, Jovan D., Milošević, Milena D., Marinković, Aleksandar D., "Microwave-Assisted of synthesis and characterizations of levulinic acid (LA)" (2019),
https://hdl.handle.net/21.15107/rcub_cer_6866 .

TY  - CONF
AU  - Linić, Suzana Lj.
AU  - Radojković, Bojana M.
AU  - Ristić, Slavica
AU  - Vasović, Ivana V.
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/5444
AB  - The investigations of the turbulence in the flow are one of the most expensive, thus the improvement of existing ones and the research related to the new methods are in continual development. The multidisciplinary approach led to the application of the infrared thermography in the turbulent boundary layer observations with the endpoint goal of energy and cost savings in its early stages. This work presents the use of the industrial type infrared thermography for identification of the turbulent zones in the free convective flow, so far the less investigated problem related to convection heat transfer. It was shown that the transient spot temperature difference, measured on the complex geometry of the real-scale coal ventilation mill, of the Thermal plant “Kostolac B”, by an infrared camera, is a good parameter for identification of the most influenced positions by turbulence. The defined fields with maximal transient temperature difference are in accordance with theory and values calculated by numerical simulations for clean geometry, confirming the assumptions. The described method is also convenient for use in cases when the other methods are not applicable because of the complex geometry, unapproachable, or for the other similar reasons. The results from this work would support the more precise measurements with the research type infrared camera, the other methods for measurements.
PB  - Serbian Society of Mechanics
C3  - Proceedings - The 7th International congress of Serbian Society of Mechanics, 24.09-26/06, 2019, Sremski Karlovci
T1  - One method for ordering turbulence measuring places applied to free-convection flow around thermal plant coal mill
VL  - 7
SP  - p.M3g
UR  - https://hdl.handle.net/21.15107/rcub_cer_5444
ER  - 

@conference{
author = "Linić, Suzana Lj. and Radojković, Bojana M. and Ristić, Slavica and Vasović, Ivana V.",
year = "2019",
abstract = "The investigations of the turbulence in the flow are one of the most expensive, thus the improvement of existing ones and the research related to the new methods are in continual development. The multidisciplinary approach led to the application of the infrared thermography in the turbulent boundary layer observations with the endpoint goal of energy and cost savings in its early stages. This work presents the use of the industrial type infrared thermography for identification of the turbulent zones in the free convective flow, so far the less investigated problem related to convection heat transfer. It was shown that the transient spot temperature difference, measured on the complex geometry of the real-scale coal ventilation mill, of the Thermal plant “Kostolac B”, by an infrared camera, is a good parameter for identification of the most influenced positions by turbulence. The defined fields with maximal transient temperature difference are in accordance with theory and values calculated by numerical simulations for clean geometry, confirming the assumptions. The described method is also convenient for use in cases when the other methods are not applicable because of the complex geometry, unapproachable, or for the other similar reasons. The results from this work would support the more precise measurements with the research type infrared camera, the other methods for measurements.",
publisher = "Serbian Society of Mechanics",
journal = "Proceedings - The 7th International congress of Serbian Society of Mechanics, 24.09-26/06, 2019, Sremski Karlovci",
title = "One method for ordering turbulence measuring places applied to free-convection flow around thermal plant coal mill",
volume = "7",
pages = "p.M3g",
url = "https://hdl.handle.net/21.15107/rcub_cer_5444"
}

Linić, S. Lj., Radojković, B. M., Ristić, S.,& Vasović, I. V.. (2019). One method for ordering turbulence measuring places applied to free-convection flow around thermal plant coal mill. in Proceedings - The 7th International congress of Serbian Society of Mechanics, 24.09-26/06, 2019, Sremski Karlovci
Serbian Society of Mechanics., 7, p.M3g.
https://hdl.handle.net/21.15107/rcub_cer_5444

Linić SL, Radojković BM, Ristić S, Vasović IV. One method for ordering turbulence measuring places applied to free-convection flow around thermal plant coal mill. in Proceedings - The 7th International congress of Serbian Society of Mechanics, 24.09-26/06, 2019, Sremski Karlovci. 2019;7:p.M3g.
https://hdl.handle.net/21.15107/rcub_cer_5444 .

Linić, Suzana Lj., Radojković, Bojana M., Ristić, Slavica, Vasović, Ivana V., "One method for ordering turbulence measuring places applied to free-convection flow around thermal plant coal mill" in Proceedings - The 7th International congress of Serbian Society of Mechanics, 24.09-26/06, 2019, Sremski Karlovci, 7 (2019):p.M3g,
https://hdl.handle.net/21.15107/rcub_cer_5444 .

TY  - JOUR
AU  - Jegdić, Bore
AU  - Bobić, Biljana
AU  - Radojković, Bojana
AU  - Alić, Behar
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3375
AB  - The influence of welding parameters on the resistance to pitting corrosion in welded joints of X5CrNi18-10 stainless steel was studied. Welding was performed by a TIG procedure in a shielding gas containing different amounts of nitrogen. The welding speed, the deposition rate of the filler wire, and the shielding gas flow rate were constant, which allowed the nitrogen content in the weld metal to be directly dependent on the nitrogen content in the shielding gas. It was shown that welding current and arc energy had a significantly lower influence on the resistance to pit formation and pit growth, than the nitrogen content in the shielding gas. Pitting corrosion testing was conducted using the potentiodynamic polarization method. The resistance to pit formation increases with the increase in nitrogen content in the weld metal, while the resistance to pit growth decreases. The microstructure of the weld metal becomes more homogeneous in the presence of nitrogen and the distribution of chromium more uniform, which leads to the increased resistance to pit formation. Also, due to the formation of ammonia ions, the pH value of the solution within the pit is higher than in the bulk solution, which also increases the resistance to pit formation.
PB  - Springer
T2  - Welding in the World
T1  - Influence of welding parameters on pit initiation and pit growth in welded joints of X5CrNi18-10 stainless steel
VL  - 63
IS  - 1
SP  - 167
EP  - 179
DO  - 10.1007/s40194-018-0644-0
ER  - 

@article{
author = "Jegdić, Bore and Bobić, Biljana and Radojković, Bojana and Alić, Behar",
year = "2019",
abstract = "The influence of welding parameters on the resistance to pitting corrosion in welded joints of X5CrNi18-10 stainless steel was studied. Welding was performed by a TIG procedure in a shielding gas containing different amounts of nitrogen. The welding speed, the deposition rate of the filler wire, and the shielding gas flow rate were constant, which allowed the nitrogen content in the weld metal to be directly dependent on the nitrogen content in the shielding gas. It was shown that welding current and arc energy had a significantly lower influence on the resistance to pit formation and pit growth, than the nitrogen content in the shielding gas. Pitting corrosion testing was conducted using the potentiodynamic polarization method. The resistance to pit formation increases with the increase in nitrogen content in the weld metal, while the resistance to pit growth decreases. The microstructure of the weld metal becomes more homogeneous in the presence of nitrogen and the distribution of chromium more uniform, which leads to the increased resistance to pit formation. Also, due to the formation of ammonia ions, the pH value of the solution within the pit is higher than in the bulk solution, which also increases the resistance to pit formation.",
publisher = "Springer",
journal = "Welding in the World",
title = "Influence of welding parameters on pit initiation and pit growth in welded joints of X5CrNi18-10 stainless steel",
volume = "63",
number = "1",
pages = "167-179",
doi = "10.1007/s40194-018-0644-0"
}

Jegdić, B., Bobić, B., Radojković, B.,& Alić, B.. (2019). Influence of welding parameters on pit initiation and pit growth in welded joints of X5CrNi18-10 stainless steel. in Welding in the World
Springer., 63(1), 167-179.
https://doi.org/10.1007/s40194-018-0644-0

Jegdić B, Bobić B, Radojković B, Alić B. Influence of welding parameters on pit initiation and pit growth in welded joints of X5CrNi18-10 stainless steel. in Welding in the World. 2019;63(1):167-179.
doi:10.1007/s40194-018-0644-0 .

Jegdić, Bore, Bobić, Biljana, Radojković, Bojana, Alić, Behar, "Influence of welding parameters on pit initiation and pit growth in welded joints of X5CrNi18-10 stainless steel" in Welding in the World, 63, no. 1 (2019):167-179,
https://doi.org/10.1007/s40194-018-0644-0 . .