TY  - JOUR
AU  - Vukašinović, Jelena
AU  - Počuča-Nešić, Milica
AU  - Luković Golić, Danijela
AU  - Ribić, Vesna
AU  - Branković, Zorica
AU  - Savić, Slavica M.
AU  - Dapčević, Aleksandra
AU  - Bernik, Slavko
AU  - Podlogar, Matejka
AU  - Kocen, Matej
AU  - Rapljenović, Željko
AU  - Ivek, Tomislav
AU  - Lazović, Vladimir
AU  - Dojčinović, Biljana
AU  - Branković, Goran
PY  - 2020
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3628
AB  - Antimony doped barium-stannate dense ceramic materials were synthesized using spark plasma sintering technique out of mechanically activated precursor powders. The influence of various Sb concentrations (x =0.00 – 0.10) on properties of BaSn1-xSbxO3 ceramics was investigated. Relative densities of prepared samples were in the range of (79–96) %. TEM analysis revealed the presence of many dislocations in undoped BaSnO3, and their significant reduction upon doping with Sb. All samples except BaSn0.92Sb0.08O3 exhibit non-linear I-U characteristic, typical for semiconductors with potential barrier at grain boundaries. Low angle grain boundaries found only in BaSn0.92Sb0.08O3 caused the loss of potential barrier at grain boundaries which was confirmed by AC impedance spectroscopy measurements. Consequently, BaSn0.92Sb0.08O3 showed the lowest electrical resistivity and linear I-U characteristic. UV–vis analysis confirmed the increasing of band gap (Burstein–Moss shift) values in all doped samples.
PB  - Elsevier
T2  - Journal of the European Ceramic Society
T1  - The structural, electrical and optical properties of spark plasma sintered BaSn1-xSbxO3 ceramics
VL  - 40
IS  - 15
SP  - 5566
EP  - 5575
DO  - 10.1016/j.jeurceramsoc.2020.06.062
ER  - 

@article{
author = "Vukašinović, Jelena and Počuča-Nešić, Milica and Luković Golić, Danijela and Ribić, Vesna and Branković, Zorica and Savić, Slavica M. and Dapčević, Aleksandra and Bernik, Slavko and Podlogar, Matejka and Kocen, Matej and Rapljenović, Željko and Ivek, Tomislav and Lazović, Vladimir and Dojčinović, Biljana and Branković, Goran",
year = "2020",
abstract = "Antimony doped barium-stannate dense ceramic materials were synthesized using spark plasma sintering technique out of mechanically activated precursor powders. The influence of various Sb concentrations (x =0.00 – 0.10) on properties of BaSn1-xSbxO3 ceramics was investigated. Relative densities of prepared samples were in the range of (79–96) %. TEM analysis revealed the presence of many dislocations in undoped BaSnO3, and their significant reduction upon doping with Sb. All samples except BaSn0.92Sb0.08O3 exhibit non-linear I-U characteristic, typical for semiconductors with potential barrier at grain boundaries. Low angle grain boundaries found only in BaSn0.92Sb0.08O3 caused the loss of potential barrier at grain boundaries which was confirmed by AC impedance spectroscopy measurements. Consequently, BaSn0.92Sb0.08O3 showed the lowest electrical resistivity and linear I-U characteristic. UV–vis analysis confirmed the increasing of band gap (Burstein–Moss shift) values in all doped samples.",
publisher = "Elsevier",
journal = "Journal of the European Ceramic Society",
title = "The structural, electrical and optical properties of spark plasma sintered BaSn1-xSbxO3 ceramics",
volume = "40",
number = "15",
pages = "5566-5575",
doi = "10.1016/j.jeurceramsoc.2020.06.062"
}

Vukašinović, J., Počuča-Nešić, M., Luković Golić, D., Ribić, V., Branković, Z., Savić, S. M., Dapčević, A., Bernik, S., Podlogar, M., Kocen, M., Rapljenović, Ž., Ivek, T., Lazović, V., Dojčinović, B.,& Branković, G.. (2020). The structural, electrical and optical properties of spark plasma sintered BaSn1-xSbxO3 ceramics. in Journal of the European Ceramic Society
Elsevier., 40(15), 5566-5575.
https://doi.org/10.1016/j.jeurceramsoc.2020.06.062

Vukašinović J, Počuča-Nešić M, Luković Golić D, Ribić V, Branković Z, Savić SM, Dapčević A, Bernik S, Podlogar M, Kocen M, Rapljenović Ž, Ivek T, Lazović V, Dojčinović B, Branković G. The structural, electrical and optical properties of spark plasma sintered BaSn1-xSbxO3 ceramics. in Journal of the European Ceramic Society. 2020;40(15):5566-5575.
doi:10.1016/j.jeurceramsoc.2020.06.062 .

Vukašinović, Jelena, Počuča-Nešić, Milica, Luković Golić, Danijela, Ribić, Vesna, Branković, Zorica, Savić, Slavica M., Dapčević, Aleksandra, Bernik, Slavko, Podlogar, Matejka, Kocen, Matej, Rapljenović, Željko, Ivek, Tomislav, Lazović, Vladimir, Dojčinović, Biljana, Branković, Goran, "The structural, electrical and optical properties of spark plasma sintered BaSn1-xSbxO3 ceramics" in Journal of the European Ceramic Society, 40, no. 15 (2020):5566-5575,
https://doi.org/10.1016/j.jeurceramsoc.2020.06.062 . .

TY  - JOUR
AU  - Vukašinović, Jelena
AU  - Počuča-Nešić, Milica
AU  - Luković Golić, Danijela
AU  - Ribić, Vesna
AU  - Branković, Zorica
AU  - Savić, Slavica M.
AU  - Dapčević, Aleksandra
AU  - Bernik, Slavko
AU  - Podlogar, Matejka
AU  - Kocen, Matej
AU  - Rapljenović, Željko
AU  - Ivek, Tomislav
AU  - Lazović, Vladimir
AU  - Dojčinović, Biljana
AU  - Branković, Goran
PY  - 2020
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3629
AB  - Antimony doped barium-stannate dense ceramic materials were synthesized using spark plasma sintering technique out of mechanically activated precursor powders. The influence of various Sb concentrations (x =0.00 – 0.10) on properties of BaSn1-xSbxO3 ceramics was investigated. Relative densities of prepared samples were in the range of (79–96) %. TEM analysis revealed the presence of many dislocations in undoped BaSnO3, and their significant reduction upon doping with Sb. All samples except BaSn0.92Sb0.08O3 exhibit non-linear I-U characteristic, typical for semiconductors with potential barrier at grain boundaries. Low angle grain boundaries found only in BaSn0.92Sb0.08O3 caused the loss of potential barrier at grain boundaries which was confirmed by AC impedance spectroscopy measurements. Consequently, BaSn0.92Sb0.08O3 showed the lowest electrical resistivity and linear I-U characteristic. UV–vis analysis confirmed the increasing of band gap (Burstein–Moss shift) values in all doped samples.
PB  - Elsevier
T2  - Journal of the European Ceramic Society
T1  - The structural, electrical and optical properties of spark plasma sintered BaSn1-xSbxO3 ceramics
VL  - 40
IS  - 15
SP  - 5566
EP  - 5575
DO  - 10.1016/j.jeurceramsoc.2020.06.062
ER  - 

@article{
author = "Vukašinović, Jelena and Počuča-Nešić, Milica and Luković Golić, Danijela and Ribić, Vesna and Branković, Zorica and Savić, Slavica M. and Dapčević, Aleksandra and Bernik, Slavko and Podlogar, Matejka and Kocen, Matej and Rapljenović, Željko and Ivek, Tomislav and Lazović, Vladimir and Dojčinović, Biljana and Branković, Goran",
year = "2020",
abstract = "Antimony doped barium-stannate dense ceramic materials were synthesized using spark plasma sintering technique out of mechanically activated precursor powders. The influence of various Sb concentrations (x =0.00 – 0.10) on properties of BaSn1-xSbxO3 ceramics was investigated. Relative densities of prepared samples were in the range of (79–96) %. TEM analysis revealed the presence of many dislocations in undoped BaSnO3, and their significant reduction upon doping with Sb. All samples except BaSn0.92Sb0.08O3 exhibit non-linear I-U characteristic, typical for semiconductors with potential barrier at grain boundaries. Low angle grain boundaries found only in BaSn0.92Sb0.08O3 caused the loss of potential barrier at grain boundaries which was confirmed by AC impedance spectroscopy measurements. Consequently, BaSn0.92Sb0.08O3 showed the lowest electrical resistivity and linear I-U characteristic. UV–vis analysis confirmed the increasing of band gap (Burstein–Moss shift) values in all doped samples.",
publisher = "Elsevier",
journal = "Journal of the European Ceramic Society",
title = "The structural, electrical and optical properties of spark plasma sintered BaSn1-xSbxO3 ceramics",
volume = "40",
number = "15",
pages = "5566-5575",
doi = "10.1016/j.jeurceramsoc.2020.06.062"
}

Vukašinović, J., Počuča-Nešić, M., Luković Golić, D., Ribić, V., Branković, Z., Savić, S. M., Dapčević, A., Bernik, S., Podlogar, M., Kocen, M., Rapljenović, Ž., Ivek, T., Lazović, V., Dojčinović, B.,& Branković, G.. (2020). The structural, electrical and optical properties of spark plasma sintered BaSn1-xSbxO3 ceramics. in Journal of the European Ceramic Society
Elsevier., 40(15), 5566-5575.
https://doi.org/10.1016/j.jeurceramsoc.2020.06.062

Vukašinović J, Počuča-Nešić M, Luković Golić D, Ribić V, Branković Z, Savić SM, Dapčević A, Bernik S, Podlogar M, Kocen M, Rapljenović Ž, Ivek T, Lazović V, Dojčinović B, Branković G. The structural, electrical and optical properties of spark plasma sintered BaSn1-xSbxO3 ceramics. in Journal of the European Ceramic Society. 2020;40(15):5566-5575.
doi:10.1016/j.jeurceramsoc.2020.06.062 .

Vukašinović, Jelena, Počuča-Nešić, Milica, Luković Golić, Danijela, Ribić, Vesna, Branković, Zorica, Savić, Slavica M., Dapčević, Aleksandra, Bernik, Slavko, Podlogar, Matejka, Kocen, Matej, Rapljenović, Željko, Ivek, Tomislav, Lazović, Vladimir, Dojčinović, Biljana, Branković, Goran, "The structural, electrical and optical properties of spark plasma sintered BaSn1-xSbxO3 ceramics" in Journal of the European Ceramic Society, 40, no. 15 (2020):5566-5575,
https://doi.org/10.1016/j.jeurceramsoc.2020.06.062 . .

TY  - JOUR
AU  - Nikolić, Pantelija M.
AU  - Koenig, W
AU  - Vujatović, Stevan S.
AU  - Blagojević, Vladimir
AU  - Luković, Danijela
AU  - Savić, Slavica M.
AU  - Radulović, Katarina
AU  - Urošević, Dragan
AU  - Nikolić, Maria Vesna
PY  - 2007
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/5687
AB  - Single crystal samples of lead telluride doped with cerium were made using the Bridgman method. Far infrared reflectivity spectra in the temperature range from 10 to 300 K are presented. The experimental data were numerically analyzed using a fitting procedure based on the plasmon–phonon interaction model and optical parameters were determined. Two additional local modes were observed at about 138 and 337 cm−1. The origin of these local vibrational impurity modes was discussed.
PB  - Elsevier
T2  - Journal of Alloys and Compounds
T1  - Far infrared properties of PbTe doped with cerium
VL  - 433
IS  - 1-2
SP  - 292
EP  - 295
DO  - 10.1016/j.jallcom.2006.06.066
ER  - 

@article{
author = "Nikolić, Pantelija M. and Koenig, W and Vujatović, Stevan S. and Blagojević, Vladimir and Luković, Danijela and Savić, Slavica M. and Radulović, Katarina and Urošević, Dragan and Nikolić, Maria Vesna",
year = "2007",
abstract = "Single crystal samples of lead telluride doped with cerium were made using the Bridgman method. Far infrared reflectivity spectra in the temperature range from 10 to 300 K are presented. The experimental data were numerically analyzed using a fitting procedure based on the plasmon–phonon interaction model and optical parameters were determined. Two additional local modes were observed at about 138 and 337 cm−1. The origin of these local vibrational impurity modes was discussed.",
publisher = "Elsevier",
journal = "Journal of Alloys and Compounds",
title = "Far infrared properties of PbTe doped with cerium",
volume = "433",
number = "1-2",
pages = "292-295",
doi = "10.1016/j.jallcom.2006.06.066"
}

Nikolić, P. M., Koenig, W., Vujatović, S. S., Blagojević, V., Luković, D., Savić, S. M., Radulović, K., Urošević, D.,& Nikolić, M. V.. (2007). Far infrared properties of PbTe doped with cerium. in Journal of Alloys and Compounds
Elsevier., 433(1-2), 292-295.
https://doi.org/10.1016/j.jallcom.2006.06.066

Nikolić PM, Koenig W, Vujatović SS, Blagojević V, Luković D, Savić SM, Radulović K, Urošević D, Nikolić MV. Far infrared properties of PbTe doped with cerium. in Journal of Alloys and Compounds. 2007;433(1-2):292-295.
doi:10.1016/j.jallcom.2006.06.066 .

Nikolić, Pantelija M., Koenig, W, Vujatović, Stevan S., Blagojević, Vladimir, Luković, Danijela, Savić, Slavica M., Radulović, Katarina, Urošević, Dragan, Nikolić, Maria Vesna, "Far infrared properties of PbTe doped with cerium" in Journal of Alloys and Compounds, 433, no. 1-2 (2007):292-295,
https://doi.org/10.1016/j.jallcom.2006.06.066 . .

TY  - CONF
AU  - Aleksić, Obrad S.
AU  - Savić, Slavica M.
AU  - Luković, Miloljub
AU  - Radulović, Katarina
AU  - Lukić, Lazar S.
PY  - 2006
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/279
AB  - An investigation path starting from (Mn,Ni,Co,Fe)3O4 nanometric powder preparation, NTC thick-film characterization, realization and optimization of new planar thermistor geometries to custom design thermistors and their application for temperature and volume airflow sensors was recently determined. The aim was to make custom designed segmented NTC thermistors printed and sintered on alumina. Two types of volume airflow sensors were formed: indirectly heated and self-heated. A pair of segmented thermistors was placed in an air guide and connected to differential branches of the Wheatstone bridge. A heater was placed in the middle between the thermistors for the indirectly heated type, while for the self-heated type the same thermistors were self-heated by a constant current source. First the thermistor responses vs. the airflow (calibration curves) were measured, and then thermistor responses in time (inertia) to fast airflow changes from the minimum to the maximum. The results obtained could be applied in air conditioning for air guide flow regulation.
C3  - Materials Science Forum
T1  - Segmented thermistors printed by NTC nanometric paste and applied in volume air-flow sensors
VL  - 518
SP  - 247
EP  - 252
DO  - 10.4028/www.scientific.net/MSF.518.247
ER  - 

@conference{
author = "Aleksić, Obrad S. and Savić, Slavica M. and Luković, Miloljub and Radulović, Katarina and Lukić, Lazar S.",
year = "2006",
abstract = "An investigation path starting from (Mn,Ni,Co,Fe)3O4 nanometric powder preparation, NTC thick-film characterization, realization and optimization of new planar thermistor geometries to custom design thermistors and their application for temperature and volume airflow sensors was recently determined. The aim was to make custom designed segmented NTC thermistors printed and sintered on alumina. Two types of volume airflow sensors were formed: indirectly heated and self-heated. A pair of segmented thermistors was placed in an air guide and connected to differential branches of the Wheatstone bridge. A heater was placed in the middle between the thermistors for the indirectly heated type, while for the self-heated type the same thermistors were self-heated by a constant current source. First the thermistor responses vs. the airflow (calibration curves) were measured, and then thermistor responses in time (inertia) to fast airflow changes from the minimum to the maximum. The results obtained could be applied in air conditioning for air guide flow regulation.",
journal = "Materials Science Forum",
title = "Segmented thermistors printed by NTC nanometric paste and applied in volume air-flow sensors",
volume = "518",
pages = "247-252",
doi = "10.4028/www.scientific.net/MSF.518.247"
}

Aleksić, O. S., Savić, S. M., Luković, M., Radulović, K.,& Lukić, L. S.. (2006). Segmented thermistors printed by NTC nanometric paste and applied in volume air-flow sensors. in Materials Science Forum, 518, 247-252.
https://doi.org/10.4028/www.scientific.net/MSF.518.247

Aleksić OS, Savić SM, Luković M, Radulović K, Lukić LS. Segmented thermistors printed by NTC nanometric paste and applied in volume air-flow sensors. in Materials Science Forum. 2006;518:247-252.
doi:10.4028/www.scientific.net/MSF.518.247 .

Aleksić, Obrad S., Savić, Slavica M., Luković, Miloljub, Radulović, Katarina, Lukić, Lazar S., "Segmented thermistors printed by NTC nanometric paste and applied in volume air-flow sensors" in Materials Science Forum, 518 (2006):247-252,
https://doi.org/10.4028/www.scientific.net/MSF.518.247 . .

TY  - JOUR
AU  - Aleksić, Obrad A.
AU  - Nikolić, Pantelija M.
AU  - Luković, Danijela
AU  - Savić, Slavica M.
AU  - Vasiljević-Radović, Dana
AU  - Radulović, Katarina
AU  - Lukić, Lazar
AU  - Bojičić, A.
AU  - Urošević, Dragan
PY  - 2005
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/5701
AB  - The thermal diffusivity of thick NTC layers based on a metal oxide powder mixture was measured at room temperature by the photoacoustic (PA) frequency transmission technique. The experimental PA amplitude and phase diagrams were numerically analyzed and the thermal diffusivity and electron transport parameters were calculated.
PB  - EDP Sciences
T2  - Journal de Physique IV
T1  - Investigation of the thermal diffusivity of thick film NTC layers obtained with the photoacoustic method
VL  - 125
SP  - 431
EP  - 433
DO  - 10.1051/jp4:2005125101
ER  - 

@article{
author = "Aleksić, Obrad A. and Nikolić, Pantelija M. and Luković, Danijela and Savić, Slavica M. and Vasiljević-Radović, Dana and Radulović, Katarina and Lukić, Lazar and Bojičić, A. and Urošević, Dragan",
year = "2005",
abstract = "The thermal diffusivity of thick NTC layers based on a metal oxide powder mixture was measured at room temperature by the photoacoustic (PA) frequency transmission technique. The experimental PA amplitude and phase diagrams were numerically analyzed and the thermal diffusivity and electron transport parameters were calculated.",
publisher = "EDP Sciences",
journal = "Journal de Physique IV",
title = "Investigation of the thermal diffusivity of thick film NTC layers obtained with the photoacoustic method",
volume = "125",
pages = "431-433",
doi = "10.1051/jp4:2005125101"
}

Aleksić, O. A., Nikolić, P. M., Luković, D., Savić, S. M., Vasiljević-Radović, D., Radulović, K., Lukić, L., Bojičić, A.,& Urošević, D.. (2005). Investigation of the thermal diffusivity of thick film NTC layers obtained with the photoacoustic method. in Journal de Physique IV
EDP Sciences., 125, 431-433.
https://doi.org/10.1051/jp4:2005125101

Aleksić OA, Nikolić PM, Luković D, Savić SM, Vasiljević-Radović D, Radulović K, Lukić L, Bojičić A, Urošević D. Investigation of the thermal diffusivity of thick film NTC layers obtained with the photoacoustic method. in Journal de Physique IV. 2005;125:431-433.
doi:10.1051/jp4:2005125101 .

Aleksić, Obrad A., Nikolić, Pantelija M., Luković, Danijela, Savić, Slavica M., Vasiljević-Radović, Dana, Radulović, Katarina, Lukić, Lazar, Bojičić, A., Urošević, Dragan, "Investigation of the thermal diffusivity of thick film NTC layers obtained with the photoacoustic method" in Journal de Physique IV, 125 (2005):431-433,
https://doi.org/10.1051/jp4:2005125101 . .

TY  - JOUR
AU  - Nikolić, Pantelija M.
AU  - Luković, Danijela
AU  - Savić, Slavica M.
AU  - Vasiljević-Radović, Dana
AU  - Radulović, Katarina
AU  - Vujatović, Stevan S.
AU  - Lukić, L.
AU  - Djurić, S.
AU  - Nikolić, Maria Vesna
AU  - Bojičić, Aleksandar
PY  - 2005
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/5695
AB  - Thermal and electron transport properties of single crystal NiO were determined using the photoacoustic technique. NiO single crystals were prepared using the Verneuil method and were easily cleaved parallel to the (100) plane. All samples were of the p type. Atomic force microscopy images of cleaved NiO samples were made enabling a view of steps along the (001) direction and terraces, which were between 20 nm and 100 nm thick.
PB  - EDP Sciences
T2  - Journal De Physique IV
T1  - Photoacoustic determination of thermal and electron transport properties of single crystal NiO
VL  - 125
SP  - 439
EP  - 442
DO  - 10.1051/jp4:20051250103
ER  - 

@article{
author = "Nikolić, Pantelija M. and Luković, Danijela and Savić, Slavica M. and Vasiljević-Radović, Dana and Radulović, Katarina and Vujatović, Stevan S. and Lukić, L. and Djurić, S. and Nikolić, Maria Vesna and Bojičić, Aleksandar",
year = "2005",
abstract = "Thermal and electron transport properties of single crystal NiO were determined using the photoacoustic technique. NiO single crystals were prepared using the Verneuil method and were easily cleaved parallel to the (100) plane. All samples were of the p type. Atomic force microscopy images of cleaved NiO samples were made enabling a view of steps along the (001) direction and terraces, which were between 20 nm and 100 nm thick.",
publisher = "EDP Sciences",
journal = "Journal De Physique IV",
title = "Photoacoustic determination of thermal and electron transport properties of single crystal NiO",
volume = "125",
pages = "439-442",
doi = "10.1051/jp4:20051250103"
}

Nikolić, P. M., Luković, D., Savić, S. M., Vasiljević-Radović, D., Radulović, K., Vujatović, S. S., Lukić, L., Djurić, S., Nikolić, M. V.,& Bojičić, A.. (2005). Photoacoustic determination of thermal and electron transport properties of single crystal NiO. in Journal De Physique IV
EDP Sciences., 125, 439-442.
https://doi.org/10.1051/jp4:20051250103

Nikolić PM, Luković D, Savić SM, Vasiljević-Radović D, Radulović K, Vujatović SS, Lukić L, Djurić S, Nikolić MV, Bojičić A. Photoacoustic determination of thermal and electron transport properties of single crystal NiO. in Journal De Physique IV. 2005;125:439-442.
doi:10.1051/jp4:20051250103 .

Nikolić, Pantelija M., Luković, Danijela, Savić, Slavica M., Vasiljević-Radović, Dana, Radulović, Katarina, Vujatović, Stevan S., Lukić, L., Djurić, S., Nikolić, Maria Vesna, Bojičić, Aleksandar, "Photoacoustic determination of thermal and electron transport properties of single crystal NiO" in Journal De Physique IV, 125 (2005):439-442,
https://doi.org/10.1051/jp4:20051250103 . .

TY  - JOUR
AU  - Nikolić, Pantelija M.
AU  - Konig, W.
AU  - Luković, Danijela
AU  - Savić, Slavica M.
AU  - Vujatović, Stevan S.
AU  - Radulović, Katarina
AU  - Blagojević, Vladimir
PY  - 2004
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/5696
AB  - Single crystal samples of lead telluride doped with samarium were produced using the
Bridgman method. Far infrared reflectivity spectra in the temperature range 10 K - 300 K are
presented and numerically analyzed using a fitting procedure based on a modified plasmon phonon
interaction model. The optical parameters were determined and three local modes of
samarium were observed at about 167 cm-1, 227 cm-1 and 486 cm-1.
PB  - Bucharest, Romania : National Institute of Research and Development for Optoelectronic
T2  - Journal of Optoelectronics and Advanced Materials
T1  - Far infrared characterization of samarium doped single crystal PbTe
VL  - 6
IS  - 3
SP  - 811
EP  - 816
UR  - https://hdl.handle.net/21.15107/rcub_cer_5696
ER  - 

@article{
author = "Nikolić, Pantelija M. and Konig, W. and Luković, Danijela and Savić, Slavica M. and Vujatović, Stevan S. and Radulović, Katarina and Blagojević, Vladimir",
year = "2004",
abstract = "Single crystal samples of lead telluride doped with samarium were produced using the
Bridgman method. Far infrared reflectivity spectra in the temperature range 10 K - 300 K are
presented and numerically analyzed using a fitting procedure based on a modified plasmon phonon
interaction model. The optical parameters were determined and three local modes of
samarium were observed at about 167 cm-1, 227 cm-1 and 486 cm-1.",
publisher = "Bucharest, Romania : National Institute of Research and Development for Optoelectronic",
journal = "Journal of Optoelectronics and Advanced Materials",
title = "Far infrared characterization of samarium doped single crystal PbTe",
volume = "6",
number = "3",
pages = "811-816",
url = "https://hdl.handle.net/21.15107/rcub_cer_5696"
}

Nikolić, P. M., Konig, W., Luković, D., Savić, S. M., Vujatović, S. S., Radulović, K.,& Blagojević, V.. (2004). Far infrared characterization of samarium doped single crystal PbTe. in Journal of Optoelectronics and Advanced Materials
Bucharest, Romania : National Institute of Research and Development for Optoelectronic., 6(3), 811-816.
https://hdl.handle.net/21.15107/rcub_cer_5696

Nikolić PM, Konig W, Luković D, Savić SM, Vujatović SS, Radulović K, Blagojević V. Far infrared characterization of samarium doped single crystal PbTe. in Journal of Optoelectronics and Advanced Materials. 2004;6(3):811-816.
https://hdl.handle.net/21.15107/rcub_cer_5696 .

Nikolić, Pantelija M., Konig, W., Luković, Danijela, Savić, Slavica M., Vujatović, Stevan S., Radulović, Katarina, Blagojević, Vladimir, "Far infrared characterization of samarium doped single crystal PbTe" in Journal of Optoelectronics and Advanced Materials, 6, no. 3 (2004):811-816,
https://hdl.handle.net/21.15107/rcub_cer_5696 .