TY  - CONF
AU  - Popović, Miljana
AU  - Alil, Ana
AU  - Gligorijević, Bojan
AU  - Romhanji, Endre
PY  - 2023
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/6246
AB  - In this study we investigated the effect of cold rolling reductions and different annealing conditions, on the mechanical
properties and corrosion resistance of an AA5182 type Al-Mg alloy. Material was industrially produced and supplied as
hot rolled 12 mm thick plates. Further lab-processing included cold rolling with 40-85% reduction in thickness, and 2h
of annealing in the range of temperatures from 300-350°C. Annealed specimens were used for room temperature tensile
testing while corrosion testing was performed on the annealed and sensitized specimens. Intergranular corrosion (IGC)
susceptibility was determined by nitric acid mass loss test (NAMLT) for the selected states.
The results showed that corrosion resistance, tensile strength and yield point elongation were mostly affected by a degree
of cold deformation. It was found that increasing in cold rolling reduction from 40-85% before annealing causes an
improved strength level due to grain size refinement. However, yield point elongation became more pronounced and a
tendency towards Lüdering as undesirable surface appearance was increased. NAMLT testing showed that the material
was corrosion resistant in as-annealed condition while it became susceptible to intergranular corrosion after sensitization
treatment. IGC susceptibility of sensitized specimens increases with cold rolling reduction and a grain size refinement.
PB  - Association of Metallurgical Engineers of Serbia (AMES)
C3  - Proceedings of the 5th Metallurgical and Materials Engineering Congress of South-East Europe, 7-10.06.2023, Trebinje, Bosnia and Herzegovina
T1  - Influence of cold rolling and annealing on the mechanical and corrosion properties of an AA5182 Al-Mg alloy
SP  - 291
EP  - 297
UR  - https://hdl.handle.net/21.15107/rcub_cer_6246
ER  - 

@conference{
author = "Popović, Miljana and Alil, Ana and Gligorijević, Bojan and Romhanji, Endre",
year = "2023",
abstract = "In this study we investigated the effect of cold rolling reductions and different annealing conditions, on the mechanical
properties and corrosion resistance of an AA5182 type Al-Mg alloy. Material was industrially produced and supplied as
hot rolled 12 mm thick plates. Further lab-processing included cold rolling with 40-85% reduction in thickness, and 2h
of annealing in the range of temperatures from 300-350°C. Annealed specimens were used for room temperature tensile
testing while corrosion testing was performed on the annealed and sensitized specimens. Intergranular corrosion (IGC)
susceptibility was determined by nitric acid mass loss test (NAMLT) for the selected states.
The results showed that corrosion resistance, tensile strength and yield point elongation were mostly affected by a degree
of cold deformation. It was found that increasing in cold rolling reduction from 40-85% before annealing causes an
improved strength level due to grain size refinement. However, yield point elongation became more pronounced and a
tendency towards Lüdering as undesirable surface appearance was increased. NAMLT testing showed that the material
was corrosion resistant in as-annealed condition while it became susceptible to intergranular corrosion after sensitization
treatment. IGC susceptibility of sensitized specimens increases with cold rolling reduction and a grain size refinement.",
publisher = "Association of Metallurgical Engineers of Serbia (AMES)",
journal = "Proceedings of the 5th Metallurgical and Materials Engineering Congress of South-East Europe, 7-10.06.2023, Trebinje, Bosnia and Herzegovina",
title = "Influence of cold rolling and annealing on the mechanical and corrosion properties of an AA5182 Al-Mg alloy",
pages = "291-297",
url = "https://hdl.handle.net/21.15107/rcub_cer_6246"
}

Popović, M., Alil, A., Gligorijević, B.,& Romhanji, E.. (2023). Influence of cold rolling and annealing on the mechanical and corrosion properties of an AA5182 Al-Mg alloy. in Proceedings of the 5th Metallurgical and Materials Engineering Congress of South-East Europe, 7-10.06.2023, Trebinje, Bosnia and Herzegovina
Association of Metallurgical Engineers of Serbia (AMES)., 291-297.
https://hdl.handle.net/21.15107/rcub_cer_6246

Popović M, Alil A, Gligorijević B, Romhanji E. Influence of cold rolling and annealing on the mechanical and corrosion properties of an AA5182 Al-Mg alloy. in Proceedings of the 5th Metallurgical and Materials Engineering Congress of South-East Europe, 7-10.06.2023, Trebinje, Bosnia and Herzegovina. 2023;:291-297.
https://hdl.handle.net/21.15107/rcub_cer_6246 .

Popović, Miljana, Alil, Ana, Gligorijević, Bojan, Romhanji, Endre, "Influence of cold rolling and annealing on the mechanical and corrosion properties of an AA5182 Al-Mg alloy" in Proceedings of the 5th Metallurgical and Materials Engineering Congress of South-East Europe, 7-10.06.2023, Trebinje, Bosnia and Herzegovina (2023):291-297,
https://hdl.handle.net/21.15107/rcub_cer_6246 .

TY  - JOUR
AU  - Vuksanović, Marija M.
AU  - Tomić, Nataša Z.
AU  - Mladenović, Ivana
AU  - Perić, Tamara O.
AU  - Gligorijević, Bojan
AU  - Jančić-Heinemann, Radmila
PY  - 2020
UR  - https://scindeks.ceon.rs/article.aspx?artid=0040-21762004429V
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3823
AB  - Kompozitni materijali na bazi akrilatnih fotopolimerizujućih polimera, (Bis-GMA/TEGDMA) koji predstavljaju matricu i ojačanja koja se mogu odabrati sa ciljem podešavanja svojstava dobijenih kompozita, koriste se u oblasti dentalne tehnologije. Uloga ojačanja je podešavanje mehaničkih svojstava, ali i kontrola skupljanja tokom očvršćavanja. Kao ojačanje odabrane su čestice aluminijum-oksida dopirane gvožđe oksidom (Al2O3 Fe), sintetisane korišćenjem sol-gel tehnike. U cilju simuliranja procesa primene adheziva u realnim uslovima korišćena je in vitro tehnika ispitivanja adhezije sintetisanog adheziva pri čemu je kao substrat korišćeno tkivo zuba. Dobijene vrednosti adhezije poređene su sa komercijalnim adhezivima koji se koriste u stomatologiji. Kvalitet adhezivnog spoja ocenjen je merenjem mikrotvrdoće primenom različitih opterećenja, pri čemu je procenjen način kako se ostvaruje spoj između filma i podloge. Pokazalo se da je sintetisani adheziv imao višestruko jaču adheziju u poređenju sa standardnim adhezivom korišćenim u stomatologiji (836 %).
AB  - Composite materials based on acrylate UV-cured polymers (Bis-GMA/TEGDMA) as a matrix and reinforcements that can be selected in order to adjust the properties of the obtained composite are used in the field of dental technology. The role of reinforcement is to adjust the mechanical properties, but also to control the shrinkage during curing. As reinforcement, alumina particles doped with iron oxide (Al2O3 Fe) synthesized using the sol-gel technique were selected. In order to simulate the process of adhesive application in real conditions, in vitro testing technique and adhesion properties of synthesized adhesive were used, where tooth tissue was used as a substrate. Comparison with standard adhesives used in dentistry was used to compare adhesion. The quality of the adhesive joint was evaluated using the microhardness testing method using different loads where it is estimated how the adhesive makes a connection with the substrate. It was shown that the synthesized adhesive showed significantly enhanced adhesion compared to the standard adhesive used in dentistry (836%).
PB  - Savez inženjera i tehničara Srbije
T2  - Tehnika
T1  - Poboljšana adhezija akrilnih adheziva sa zubnim tkivom uz dodatak čestica na bazi aluminijum oksida
T1  - Enhanced adhesion of acrylic adhesives with dental tissue with the addition of aluminum oxide based particles
VL  - 29
IS  - 4
SP  - 429
EP  - 433
DO  - 10.5937/tehnika2004429V
ER  - 

@article{
author = "Vuksanović, Marija M. and Tomić, Nataša Z. and Mladenović, Ivana and Perić, Tamara O. and Gligorijević, Bojan and Jančić-Heinemann, Radmila",
year = "2020",
abstract = "Kompozitni materijali na bazi akrilatnih fotopolimerizujućih polimera, (Bis-GMA/TEGDMA) koji predstavljaju matricu i ojačanja koja se mogu odabrati sa ciljem podešavanja svojstava dobijenih kompozita, koriste se u oblasti dentalne tehnologije. Uloga ojačanja je podešavanje mehaničkih svojstava, ali i kontrola skupljanja tokom očvršćavanja. Kao ojačanje odabrane su čestice aluminijum-oksida dopirane gvožđe oksidom (Al2O3 Fe), sintetisane korišćenjem sol-gel tehnike. U cilju simuliranja procesa primene adheziva u realnim uslovima korišćena je in vitro tehnika ispitivanja adhezije sintetisanog adheziva pri čemu je kao substrat korišćeno tkivo zuba. Dobijene vrednosti adhezije poređene su sa komercijalnim adhezivima koji se koriste u stomatologiji. Kvalitet adhezivnog spoja ocenjen je merenjem mikrotvrdoće primenom različitih opterećenja, pri čemu je procenjen način kako se ostvaruje spoj između filma i podloge. Pokazalo se da je sintetisani adheziv imao višestruko jaču adheziju u poređenju sa standardnim adhezivom korišćenim u stomatologiji (836 %)., Composite materials based on acrylate UV-cured polymers (Bis-GMA/TEGDMA) as a matrix and reinforcements that can be selected in order to adjust the properties of the obtained composite are used in the field of dental technology. The role of reinforcement is to adjust the mechanical properties, but also to control the shrinkage during curing. As reinforcement, alumina particles doped with iron oxide (Al2O3 Fe) synthesized using the sol-gel technique were selected. In order to simulate the process of adhesive application in real conditions, in vitro testing technique and adhesion properties of synthesized adhesive were used, where tooth tissue was used as a substrate. Comparison with standard adhesives used in dentistry was used to compare adhesion. The quality of the adhesive joint was evaluated using the microhardness testing method using different loads where it is estimated how the adhesive makes a connection with the substrate. It was shown that the synthesized adhesive showed significantly enhanced adhesion compared to the standard adhesive used in dentistry (836%).",
publisher = "Savez inženjera i tehničara Srbije",
journal = "Tehnika",
title = "Poboljšana adhezija akrilnih adheziva sa zubnim tkivom uz dodatak čestica na bazi aluminijum oksida, Enhanced adhesion of acrylic adhesives with dental tissue with the addition of aluminum oxide based particles",
volume = "29",
number = "4",
pages = "429-433",
doi = "10.5937/tehnika2004429V"
}

Vuksanović, M. M., Tomić, N. Z., Mladenović, I., Perić, T. O., Gligorijević, B.,& Jančić-Heinemann, R.. (2020). Poboljšana adhezija akrilnih adheziva sa zubnim tkivom uz dodatak čestica na bazi aluminijum oksida. in Tehnika
Savez inženjera i tehničara Srbije., 29(4), 429-433.
https://doi.org/10.5937/tehnika2004429V

Vuksanović MM, Tomić NZ, Mladenović I, Perić TO, Gligorijević B, Jančić-Heinemann R. Poboljšana adhezija akrilnih adheziva sa zubnim tkivom uz dodatak čestica na bazi aluminijum oksida. in Tehnika. 2020;29(4):429-433.
doi:10.5937/tehnika2004429V .

Vuksanović, Marija M., Tomić, Nataša Z., Mladenović, Ivana, Perić, Tamara O., Gligorijević, Bojan, Jančić-Heinemann, Radmila, "Poboljšana adhezija akrilnih adheziva sa zubnim tkivom uz dodatak čestica na bazi aluminijum oksida" in Tehnika, 29, no. 4 (2020):429-433,
https://doi.org/10.5937/tehnika2004429V . .

TY  - GEN
AU  - Milašinović, Veljko
AU  - Milašinović, Dragoslav
AU  - Milašinović, Mijat
AU  - Milašinović, Nikola
AU  - Jevremović, Aleksandar
AU  - Raić, Karlo
AU  - Alil, Ana
AU  - Dikić, Stefan
AU  - Vlahović, Milica
AU  - Martinović, Sanja
AU  - Gligorijević, Bojan
PY  - 2019
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/5963
AB  - Al/Cu konektori [ a) Al/Cu bimetalne papučice, b) Al/Cu bimetalne čaure, c) Al/Cu bimetalne završnice] nastaju kontinualnim zavarivanjem trenjem Al šipke i Cu šipke. Postupak se odvija tako što se aluminijumska šipka prethodno odsečena na potrebnu dužinu stavlja u steznu glavu koja je preko elektromagnetne spojnice i kaišnog prenosnika povezana sa pogonskim elektromotorom koji obezbeđuje rotaciju. Broj obrtaja je određen kombinacijom odgovarajućih kaišnika. Bakarna šipka, prethodno isečena na odgovarajuću dužinu se stavlja u steznu glavu koja je povezana sa hidrauličnim cilindrom koji obezbeđuje potrebni pritisak. Proces se odvija u dve faze, faza trenja i faza utiskivanja.
PB  - Tehnološko-metalurški fakultet u Beogradu, Univerzitet u Beogradu
T1  - Побољшање електро-механичких својстава Al/Cu електричних конектора смањењем интерметалног слоја, поступком редуковања времена заваривања трењем
UR  - https://hdl.handle.net/21.15107/rcub_cer_5963
ER  - 

@misc{
author = "Milašinović, Veljko and Milašinović, Dragoslav and Milašinović, Mijat and Milašinović, Nikola and Jevremović, Aleksandar and Raić, Karlo and Alil, Ana and Dikić, Stefan and Vlahović, Milica and Martinović, Sanja and Gligorijević, Bojan",
year = "2019",
abstract = "Al/Cu konektori [ a) Al/Cu bimetalne papučice, b) Al/Cu bimetalne čaure, c) Al/Cu bimetalne završnice] nastaju kontinualnim zavarivanjem trenjem Al šipke i Cu šipke. Postupak se odvija tako što se aluminijumska šipka prethodno odsečena na potrebnu dužinu stavlja u steznu glavu koja je preko elektromagnetne spojnice i kaišnog prenosnika povezana sa pogonskim elektromotorom koji obezbeđuje rotaciju. Broj obrtaja je određen kombinacijom odgovarajućih kaišnika. Bakarna šipka, prethodno isečena na odgovarajuću dužinu se stavlja u steznu glavu koja je povezana sa hidrauličnim cilindrom koji obezbeđuje potrebni pritisak. Proces se odvija u dve faze, faza trenja i faza utiskivanja.",
publisher = "Tehnološko-metalurški fakultet u Beogradu, Univerzitet u Beogradu",
title = "Побољшање електро-механичких својстава Al/Cu електричних конектора смањењем интерметалног слоја, поступком редуковања времена заваривања трењем",
url = "https://hdl.handle.net/21.15107/rcub_cer_5963"
}

Milašinović, V., Milašinović, D., Milašinović, M., Milašinović, N., Jevremović, A., Raić, K., Alil, A., Dikić, S., Vlahović, M., Martinović, S.,& Gligorijević, B.. (2019). Побољшање електро-механичких својстава Al/Cu електричних конектора смањењем интерметалног слоја, поступком редуковања времена заваривања трењем. 
Tehnološko-metalurški fakultet u Beogradu, Univerzitet u Beogradu..
https://hdl.handle.net/21.15107/rcub_cer_5963

Milašinović V, Milašinović D, Milašinović M, Milašinović N, Jevremović A, Raić K, Alil A, Dikić S, Vlahović M, Martinović S, Gligorijević B. Побољшање електро-механичких својстава Al/Cu електричних конектора смањењем интерметалног слоја, поступком редуковања времена заваривања трењем. 2019;.
https://hdl.handle.net/21.15107/rcub_cer_5963 .

Milašinović, Veljko, Milašinović, Dragoslav, Milašinović, Mijat, Milašinović, Nikola, Jevremović, Aleksandar, Raić, Karlo, Alil, Ana, Dikić, Stefan, Vlahović, Milica, Martinović, Sanja, Gligorijević, Bojan, "Побољшање електро-механичких својстава Al/Cu електричних конектора смањењем интерметалног слоја, поступком редуковања времена заваривања трењем" (2019),
https://hdl.handle.net/21.15107/rcub_cer_5963 .

TY  - JOUR
AU  - Bobić, Biljana
AU  - Jegdić, Bore
AU  - Jugović, Branimir
AU  - Stevanović, Jasmina
AU  - Gligorijević, Bojan
AU  - Murariu, Alin
PY  - 2016
UR  - http://dais.sanu.ac.rs/123456789/15962
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/3151
AB  - Causes of failure of brass condenser tubes (CuZn28Sn1) in a thermal power plant in Serbia are analysed. Results of testing by Fourier transformed infrared spectroscopy (FTIR) have indicated the presence of ammonia and nitro- gen compounds on fracture surfaces and on the inner surface of the tubes. These compounds are specific agents that cause stress corrosion cracking (SCC) in brass. Analy- sis of fracture surfaces using scanning electron microscopy (SEM) has shown the brittle transgranular fracture due to the occurrence of SCC. The resistance of brass condenser tubes to other types of corrosion, such as erosion, general and selective corrosion (dezincification) is also considered. Some procedures are proposed to reduce the risk of SCC in the brass condenser tubes.
AB  - Analizirani su uzroci pojave loma kondenzatorskih cevi od mesinga CuZn28Sn1 u jednoj termoelektrani u Srbiji. Rezultati ispitivanja metodom Furijeove transformisane infracrvene spektroskopije (FTIR) ukazuju na prisustvo amonijačnih i azotnih jedinjenja na površini loma i na unutrašnjoj površini cevi. Ta jedinjenja su specifični agensi za pojavu naponske korozije mesinga. Analiza površine loma primenom skening elektronske mikroskopije (SEM) pokazala je prisustvo krtog transkistalnog loma nastalog usled pojave naponske korozije. Razmatrana je otpornost cevi od mesinga CuZn28Sn1 prema drugim vidovima koro- zije, kao što su eroziona, opšta i selektivna korozija (decin- kacija). Predloženi su postupci za smanjenje rizika od pojave naponske korozije u kondenzatorskim cevima.
PB  - Belgrade Society for Structural Integrity and Life; IMS Institute
T2  - Structural Integrity and Life
T1  - Failures of Brass Condenser Tubes
T1  - Lomovi kondenzatorskih cevi od mesinga
VL  - 16
IS  - 1
SP  - 19
EP  - 23
UR  - https://hdl.handle.net/21.15107/rcub_dais_15962
ER  - 

@article{
author = "Bobić, Biljana and Jegdić, Bore and Jugović, Branimir and Stevanović, Jasmina and Gligorijević, Bojan and Murariu, Alin",
year = "2016",
abstract = "Causes of failure of brass condenser tubes (CuZn28Sn1) in a thermal power plant in Serbia are analysed. Results of testing by Fourier transformed infrared spectroscopy (FTIR) have indicated the presence of ammonia and nitro- gen compounds on fracture surfaces and on the inner surface of the tubes. These compounds are specific agents that cause stress corrosion cracking (SCC) in brass. Analy- sis of fracture surfaces using scanning electron microscopy (SEM) has shown the brittle transgranular fracture due to the occurrence of SCC. The resistance of brass condenser tubes to other types of corrosion, such as erosion, general and selective corrosion (dezincification) is also considered. Some procedures are proposed to reduce the risk of SCC in the brass condenser tubes., Analizirani su uzroci pojave loma kondenzatorskih cevi od mesinga CuZn28Sn1 u jednoj termoelektrani u Srbiji. Rezultati ispitivanja metodom Furijeove transformisane infracrvene spektroskopije (FTIR) ukazuju na prisustvo amonijačnih i azotnih jedinjenja na površini loma i na unutrašnjoj površini cevi. Ta jedinjenja su specifični agensi za pojavu naponske korozije mesinga. Analiza površine loma primenom skening elektronske mikroskopije (SEM) pokazala je prisustvo krtog transkistalnog loma nastalog usled pojave naponske korozije. Razmatrana je otpornost cevi od mesinga CuZn28Sn1 prema drugim vidovima koro- zije, kao što su eroziona, opšta i selektivna korozija (decin- kacija). Predloženi su postupci za smanjenje rizika od pojave naponske korozije u kondenzatorskim cevima.",
publisher = "Belgrade Society for Structural Integrity and Life; IMS Institute",
journal = "Structural Integrity and Life",
title = "Failures of Brass Condenser Tubes, Lomovi kondenzatorskih cevi od mesinga",
volume = "16",
number = "1",
pages = "19-23",
url = "https://hdl.handle.net/21.15107/rcub_dais_15962"
}

Bobić, B., Jegdić, B., Jugović, B., Stevanović, J., Gligorijević, B.,& Murariu, A.. (2016). Failures of Brass Condenser Tubes. in Structural Integrity and Life
Belgrade Society for Structural Integrity and Life; IMS Institute., 16(1), 19-23.
https://hdl.handle.net/21.15107/rcub_dais_15962

Bobić B, Jegdić B, Jugović B, Stevanović J, Gligorijević B, Murariu A. Failures of Brass Condenser Tubes. in Structural Integrity and Life. 2016;16(1):19-23.
https://hdl.handle.net/21.15107/rcub_dais_15962 .

Bobić, Biljana, Jegdić, Bore, Jugović, Branimir, Stevanović, Jasmina, Gligorijević, Bojan, Murariu, Alin, "Failures of Brass Condenser Tubes" in Structural Integrity and Life, 16, no. 1 (2016):19-23,
https://hdl.handle.net/21.15107/rcub_dais_15962 .

TY  - JOUR
AU  - Jegdić, Bore
AU  - Bobić, Biljana
AU  - Gligorijević, Bojan
AU  - Mišković-Stanković, Vesna
PY  - 2014
UR  - https://cer.ihtm.bg.ac.rs/handle/123456789/1483
AB  - Corrosion properties of an aluminium alloy 7000 series were investigated by different electrochemical methods. The alloy was subjected to the one-step and to a new two-step precipitation hardening. Polarization measurements in the 3.5 wt. % NaCl solution have shown a more positive value of the pitting potential (Epit) and a higher corrosion resistance for the two-step aged alloy. The electrochemical impedance spectroscopy (EIS) has also shown that the two-step aged alloy has better corrosion properties (higher value of polarization resistance, Rp, and lower value of double-layer capacitance, Cdl) comparing to the one-step aged alloy.
AB  - Otpornost prema koroziji aluminijumske legure serije 7000 ispitivana je primenom različitih elektrohemijskih metoda. Legura je bila podvrgnuta jednostepenom i novom dvostepenom termičkom taloženju. Polarizaciona merenja u 3,5 mas.% NaCl su pokazala da legura posle dvostepenog termičkog taloženja ima pozitivniju vrednost potencijala pitinga (Epit) i veću otpornost prema koroziji. Spektroskopija elektrohemijske impedancije (SEI) je takođe pokazala da legura posle dvostepenog termičkog taloženja ima bolju otpornost prema koroziji (veću vrednost polarizacione otpornosti, Rp i manju vrednost kapacitivnosti dvojnog sloja, Cdl) u poređenju sa legurom posle jednostepenog termičkog taloženja.
PB  - Belgrade, Serbia : Engineering Society for Corrosion
T2  - Zaštita materijala
T1  - Corrosion properties of an aluminium alloy 7000 series after a new two step precipitation hardening
T1  - Otpornost prema koroziji aluminijumske legure serije 7000 posle novog dvostepenog termičkog taloženja
VL  - 55
IS  - 4
SP  - 387
EP  - 394
DO  - 10.5937/ZasMat1404387J
ER  - 

@article{
author = "Jegdić, Bore and Bobić, Biljana and Gligorijević, Bojan and Mišković-Stanković, Vesna",
year = "2014",
abstract = "Corrosion properties of an aluminium alloy 7000 series were investigated by different electrochemical methods. The alloy was subjected to the one-step and to a new two-step precipitation hardening. Polarization measurements in the 3.5 wt. % NaCl solution have shown a more positive value of the pitting potential (Epit) and a higher corrosion resistance for the two-step aged alloy. The electrochemical impedance spectroscopy (EIS) has also shown that the two-step aged alloy has better corrosion properties (higher value of polarization resistance, Rp, and lower value of double-layer capacitance, Cdl) comparing to the one-step aged alloy., Otpornost prema koroziji aluminijumske legure serije 7000 ispitivana je primenom različitih elektrohemijskih metoda. Legura je bila podvrgnuta jednostepenom i novom dvostepenom termičkom taloženju. Polarizaciona merenja u 3,5 mas.% NaCl su pokazala da legura posle dvostepenog termičkog taloženja ima pozitivniju vrednost potencijala pitinga (Epit) i veću otpornost prema koroziji. Spektroskopija elektrohemijske impedancije (SEI) je takođe pokazala da legura posle dvostepenog termičkog taloženja ima bolju otpornost prema koroziji (veću vrednost polarizacione otpornosti, Rp i manju vrednost kapacitivnosti dvojnog sloja, Cdl) u poređenju sa legurom posle jednostepenog termičkog taloženja.",
publisher = "Belgrade, Serbia : Engineering Society for Corrosion",
journal = "Zaštita materijala",
title = "Corrosion properties of an aluminium alloy 7000 series after a new two step precipitation hardening, Otpornost prema koroziji aluminijumske legure serije 7000 posle novog dvostepenog termičkog taloženja",
volume = "55",
number = "4",
pages = "387-394",
doi = "10.5937/ZasMat1404387J"
}

Jegdić, B., Bobić, B., Gligorijević, B.,& Mišković-Stanković, V.. (2014). Corrosion properties of an aluminium alloy 7000 series after a new two step precipitation hardening. in Zaštita materijala
Belgrade, Serbia : Engineering Society for Corrosion., 55(4), 387-394.
https://doi.org/10.5937/ZasMat1404387J

Jegdić B, Bobić B, Gligorijević B, Mišković-Stanković V. Corrosion properties of an aluminium alloy 7000 series after a new two step precipitation hardening. in Zaštita materijala. 2014;55(4):387-394.
doi:10.5937/ZasMat1404387J .

Jegdić, Bore, Bobić, Biljana, Gligorijević, Bojan, Mišković-Stanković, Vesna, "Corrosion properties of an aluminium alloy 7000 series after a new two step precipitation hardening" in Zaštita materijala, 55, no. 4 (2014):387-394,
https://doi.org/10.5937/ZasMat1404387J . .